Sign in
Search adsp
Subscribe to adsp
adsp by Keywords
AD1819 | AD7332 | ADSP-2106 | ADSP-21060 | ADSP-21065L | ADSP-2116 | ADSP-21160M | ADSP-2181 | ADSP-218x | ADSP-219 | ADSP-2199 | ADSP219 | BF531 | BF532 | BF533 | BF535 | Blackfin | FFT | JTAG | LDF | SDRAM | SHARC | SPORT | UART | VDSP++ | VisualDSP
Sponsor
Discussion Groups
See Also
Discussion Groups | Analog Devices DSPs
Technical discussions related to Analog Devices DSPs (including Blackfin, TigerSHARC, SHARC and ADSP-21xx DSPs).
Search Results for "sport"
ADSP 219x SPORT disable/enable [2 Articles]
nickolayorekhov - Feb 1 2009
Hello! We're using SPORT in multichannel autobuffer mode, SCLK and
TFS/RFS are generated externally.
After some special signal becomes high (let's call it RESET)
SCLK/TFS/RFS ... 
SPORT of SHARC [2 Articles]
Ralf Heuser-Lindner - May 12 2000
I have a question about the TFS signal of an
SPORT in an ADSP 21061:
I set up the TFS of SPORT 1 as follows:
Internally generated (ITFS = 1),
data independen... EZKIT 21160 SPORT [3 Articles]
Roger - Oct 4 2003
Hello,
Do someone know, if the SPORT-Connectors tolerate 5V TTL-Levels ???
I want to connect the SPORT to an 5V-Device. Is this possible??
Thank's a lot for... SPORT Hang on 21065L
ryanhalter - Jun 23 2003
I am using the ADSP21065L chip and right now just implementing a
simple sport transfer between a PC serial port and the DSP chip on a
custom board(with a RS-232 Tra... Re: SPORT Hang on 21065L
canb...@yahoo.co.in - May 25 2007
>
>
>
> I am using the ADSP21065L chip and right now just implementing a
> simple sport transfer between a PC serial port and the DSP chip on a
> custom board... SPORT VisualDSP++ Interrupt in 2191
sumi_d18 - Dec 29 2002
Hello,
Could anyone please let me know if there is a C function call to
initialize the SPORT in 2191 EZKIT. Also, what is the 'sig' value in
the interrupt func... AD1854 problem with BF537 EZ kIt Lite
isni...@gmail.com - Aug 7 2008
Hello Everyone,
I am developing an audio application using Blackfin BF537 EzKit lite. I have some problems with DAC 1854 Sport interface. I want to pass the audio data samples v... SPORT PROBLEM on ADMCF 326
srinivas ph - Jun 26 2003
hello every one out there,
can anyone help me with
the configuration of the sport of admcf 326. nothing
seem to works. i want to know if the boot code
disables ... several question in sport0,please!
zhangzs0422 - Oct 26 2004
the first:in the hardware manual----Writing to a SPORT¡¯s SPx_TX
register readies the SPORT for transmission.After the first bit of a
word has been transferre... sport comm between adsp2181, bf533 [2 Articles]
ashr...@rediffmail.com - Jun 1 2009
hi all
Am trying to implement sport comm between ADSP2181 and BF533.
My aim is to send memory contents of adsp2181 to bf533 memory via sport.
On 2181 i have disabled codec to ... Sport0 Rx Interrupts die. Need help! [2 Articles]
n_ga...@mail.ru - Aug 8 2007
I use ADSP2191 Sport0 in multichannel mode (H.100) with autobuffering DMA
TFS/RFS external, SCLK external ... 8,192 mhz
I need to enable disable and reenable again Rx.
After b... Programming AD1836
makarandpurohit2005 - Dec 1 2006
Hello,
We have a buffer of 1152*2 bytes,which will be filled often and
which needs to be written to the DAC. We have configured the DAC for
the sampling freq. of 48KHz.... sport communication
ashr...@rediffmail.com - Mar 3 2009
hi friends
i would like to implement sport comm using bf533.can any one give me a sample code that writes data out of sport1 into a memory location.
I initialised all the requir... serial with SPORT on ADSP-21261 work wrong!
verd...@email.it - Jan 23 2006
Hi,
I have implemented on ADSP-21261 a serial tx rx by use of sport, how suggested in the application note EE191:
At rx I set the clock of the SPORT for oversampling t... SPORT DMA Chaining for pingpong buffer [2 Articles]
hifijp2002 - Oct 1 2003
Hi all
I am coding audio multi channel input and output by 21161's SPORT DMA
chaining for pingpong buffer.
I want to code as possible as interrupt less program. ... compatibility between adsp2181 and bf533 [5 Articles]
ashr...@rediffmail.com - Jun 8 2009
Hi friends
ADSP 2181 and BF533 are not compatible. ADSP2181 is a 5V logic(TTL)
while BF533 is a 3.3V logic device.
If i need to connect ADSP2181 sport to BF533 sport is it eno... how to transfer data thru SPORT [2 Articles]
menaka - Aug 4 2004
Dear All,
I am a beginner in ADSP-BF532.I am using Blackfin summit ICE and
visual dsp++3.0 software.
how to transfer the data through SPORT&UART.what is VDK.
ho... Re: Help regarding Sport and DMA [2 Articles]
sink...@gmail.com - Feb 17 2006
Hi,
I am kind of new to this ADSP....
I am working on the ADSP BF533 EZ-kit lite example
"Audio talk through" .....
In the C code they have set the SLEN=24,since the
codec(... SPORT as SPI slave
djthurin - Aug 11 2004
Hi,
I've been trying to use a SHARC (21065 and 21262) SPORT as a SPI
slave. I have observed that when I receive data, it is right
shifted by a couple of bits (... BF533 SPORT TDM [3 Articles]
brad...@yahoo.com - Aug 1 2006
I want to connect 3 BF533s processors together using the SPORT in TDM. I wanted to make sure my thoughts were correct regarding the connections. In order to receive and transmit ... Sport communication
ashr...@rediffmail.com - Jun 3 2009
hi everybody,
I tried to establish sport comm between adsp2181 and BF533.
could not succeed.
I tested separately both 2181 and BF and are working fine.
I tried using loopback m... glueless RS232 interface to SPORT0 on 21065L
robmcgurrin - Oct 23 2006
Hi all,
I'm trying to implement a glueless RS232 interface to SPORT0 on my=20
21065L. My code is based on the ee-191 engineer to engineer=20
note, "Implementing a Glueless UA... Help regarding Sport and DMA
shwetha shwetha - Oct 22 2004
Hi,
I am kind of new to this ADSP....
I am working on the ADSP BF533 EZ-kit lite example
"Audio talk through" .....
In the C code they have set the ... adt Sport and DMA [3 Articles]
shwetha shwetha - Oct 25 2004
Hi,
I am kind of new to this ADSP....
I am working on the ADSP BF533 EZ-kit lite example
"Audio talk through" .....
In the C code they have set the ... Connecting ADSP21065L [2 Articles]
hannes_schuster - Dec 19 2001
Hello
I want to connect 3 DSP over the SPORT.
Is there any information available how to connect them, and how to
Program the SPORTS.
Is it possible to loa... ADSP2191 Interrupt in C [5 Articles]
sumithra anand - Dec 31 2002
Could anyone please let me know if there is a C
function call to
initialize the SPORT in 2191 EZKIT. Also, what is the
'sig' value in
the interrupt function for... Sport driver
cottonking2000 - Jun 3 2003
Has anyone done a sport driver for an MP3 player to the AC 97 chip?
If so need advice. May just send out RAW format but looking to do a
MP3 codec - decoder on th... Test for loop back in 21262 [3 Articles]
abhi...@wipro.com - May 18 2006
hello all,
can any one tell me how to do loop back programing and how to set hardware for this in ADSP 21262.
i tried to configure SPORT0 for tx. and SPORT 1 to rx. but i am ge... i want to confirm something in sport£¡
zhangzs0422 - Nov 18 2004
in the spx_statr there is a txs and a rxs bit,my question is that if
i send a data by sport does the txs bit is full and when the data is
send the txs is empt... Simulating SPORT DMA on 65L [4 Articles]
andor_bariska - Jan 19 2004
Hi all,
I'm getting some unexpected results from the following setup, and
perhaps someone has an idea why.
I am simulating a 65L program. The simulator uses... SPORT
Hany Ferdinando - Sep 30 2003
Hi all,
I used two ADSP-21992 boards, they are connected via SPORT. I would like to
send data from one board to the other. To detect the incoming data, I used
... SPORT for modem plz have a lookSTEV holle,Jaac [2 Articles]
ajax...@yahoo.co.in - Apr 8 2005
hello every budy.
i wanted to use sport0 for setting the modem of seimens company fpr the GSM use .which uses AT comands.
one simple task
alreday it connected... 21161'SPORT DMA work strange in VDSP3.0 Simulator
hifijp2002 - May 12 2003
Hi
I test SPORT DMA multichannel mode and Chaining of ADSP21161N in
VDSP3.0 Simulator.
I set SP0,SP1,SP2,SP3 of Stream in Simulator.
SP0,SP1 DMA is good.
S... SPORT in TDM mode
s.mo...@gmail.com - Apr 21 2009
Hi,
I am new to SHARC and I am using ADSP-21369. I was wondering if anyone could provide some example codes for SPORT in TDM mode for ADSP-21369.
Thanks,
... using sport.h with EZlite kit 2189m
bart bart - Apr 23 2001
Hello,
I have a question recarding the sport.h header file on
the EZlite kit ADSP-2189m.
If I use sport_start(0) or sport_write(0,0x55) I get
an expression erro... SPORT-UART communication with TxFs
steh...@hotmail.com - Mar 28 2007
Hi,
I am tying to communicate with a UART device though my SPORT. My TxFs and RxFs are connected, also the clock is generated by the DSP and fowwloed by the UART device.
What I ... SPORT talkthru questions.
Hanley, Tom - Jul 1 2001
Hello,
Is there a way to modify the SPORT talkthru example that comes with
the EZLAB board to just do sound out? At the moment I have a MAFE expansion
card set up... Related SPORT and SCLK frequency.. [2 Articles]
Thirumalesh - May 25 2006
Hii,
Why we want to generate the SPORT external clock must always be less than the
SCLK frequency? If i generate external clock is more than SCLK, what will happend?
Let m... ADSP21161 EZ-kit SPORT problems... [2 Articles]
Öhgren, Ulf - Jul 3 2003
Hi,
I've recently started up my 'ADSP21161N EZ-LITE' development kit. When I try
to use the serial port the serial port interrupt is continously triggered
and ... 21065L Sport interrupt held off? [3 Articles]
John Henry - Mar 20 2006
I have an instance where I intermittently lose sport data.
I am using an AKM codec that interleaves two channels into sport 0 on
the 21065L. This works perfectly. I get 16 sets o...