Hi I want to extract only y data from sframe0 (which is in UYVY 4:2:2 format) in Video inout example and save it. Please help me in this...

Hi I want to extract only y data from sframe0 (which is in UYVY 4:2:2 format) in Video inout example and save it. Please help me in this regard. Thankyou.

Hi all, I am using adsp 2188 and need to compare two 32bits numbers. I have both the numbers in 4 16 bit regs. I want to know the most optimized...

Hi all, I am using adsp 2188 and need to compare two 32bits numbers. I have both the numbers in 4 16 bit regs. I want to know the most optimized way of comparing them, as I can only compare 16 bits at a time (as it is a 16 bit processor). I have a solution in mind but it is taking a lot of extra conditions, compare the msbs first. if msbs are equal, (note that the lsbs are supposed to be un...

Hi, I am trying to interface ADSP21364 with codec AD1938 through serial port. But not able to configure AD1938 through SPI. AD1938...

Hi, I am trying to interface ADSP21364 with codec AD1938 through serial port. But not able to configure AD1938 through SPI. AD1938 has 24 bit control registers and SPI of ADSP only supports 16 and 32 bit word length is there any problem with this ? If anyone knows the configuration of control registers of codec ADF1938 please help me Regards

Hi, I have written already about this problem. But here I am trying to give more details as to what problems I am encountering. I have a...

Hi, I have written already about this problem. But here I am trying to give more details as to what problems I am encountering. I have a custom board with BF534 processor. I am using VDSP++5.0 update2 software with 90 day test drive license. We are getting a few errors when we are trying to connect our target board. I have given the list of errors which I am encountering. I have also given th...

HI I am using ADSP-21065L and encounter with the following error /////////////// ERROR DURING COMPILATION ///////////////// 24467 bytes...

HI I am using ADSP-21065L and encounter with the following error /////////////// ERROR DURING COMPILATION ///////////////// 24467 bytes eliminated in processor 'p0' For more details, see 'linker_log.xml' in the output directory. [Error li1040] ".\INS30.LDF":149 Out of memory in output section 'seg_imu' in processor 'p0' Total of 0x2a5 word(s) were not mapped. For more details, s...

Hi, I have a custom board with BF534 processor and spansion flash. When try to load the flash driver onto the board. I get the following...

Hi, I have a custom board with BF534 processor and spansion flash. When try to load the flash driver onto the board. I get the following error. "JTAG scan failed- check target power and emulator connection. Cannot load memory when target is running. error loading section "L1_code" to target." sometimes I get the following error as well. " Unable to halt processor, JTAG communication failed...

Hello How can I return from an interruption working in C Code? In other words: what's the equivalent to RTI or RETI (assembler) in C Code? I'm...

Hello How can I return from an interruption working in C Code? In other words: what's the equivalent to RTI or RETI (assembler) in C Code? I'm searching in the documentation and in forum but I don't find anything. Thanks you for all your help Eduardo Méndez

Hello I'm new using VisualDSP and Tigersharcs TS101. I've to implement with Linkports an little comunication protocol between two TS101, but I...

Hello I'm new using VisualDSP and Tigersharcs TS101. I've to implement with Linkports an little comunication protocol between two TS101, but I don't know exactly what are the steps to configure the comunication. Any of you know what are the steps? I only know that I must start activating "global HW interrupts". Thanks you for all your help Eduardo MÉNDEZ

Hi all , Could Flash be programed with out ICE , Like boot the Blackfin from SPI and then program the flash from SPI . -- Thanking...

Hi all , Could Flash be programed with out ICE , Like boot the Blackfin from SPI and then program the flash from SPI . -- Thanking you With best regards and wishes Vatsa

Hello, all. New to the board. Also new to the SHARC simulator. I'm looking for some code examples that will help me set up the 21062 serial...

Hello, all. New to the board. Also new to the SHARC simulator. I'm looking for some code examples that will help me set up the 21062 serial ports for use in the simulator. From what I've been able to gather from the documentation, the only way to read/write data from/to files when using the simulator is via the serial ports. I need to establish periodic interrupts, read several values into ...