Hi everyone
I have a problem with flash programing, I have my F2812 custom board and run my
program in internal ram then it's work good. i use xds510 emulator,
now i want to load my code into flash for stand alone working.
the problem is my code runnning but some peripheral not work in this
mode,ADC_ISR and T0_ISR are work but SCI and SPI not work, i track my code and
saw SCI and SPI ISR running but no data send to output,
I readed all ti document about flash programing but dont understand why.
 some of my initialize code and my CMD here,

i'm really confused, thank you for your attention.
-----------------------------------------------------------------------
=======================================================================
extern Uint16 CodefuncsLoadStart;
extern Uint16 CodefuncsLoadEnd;
extern Uint16 CodefuncsRunStart;

extern Uint16 econstLoadStart;
extern Uint16 econstLoadEnd;
extern Uint16 econstRunStart;

#pragma CODE_SECTION(Automatic, "Codefuncs");
#pragma CODE_SECTION(HandleMode, "Codefuncs");
#pragma CODE_SECTION(PosRead, "Codefuncs");
#pragma CODE_SECTION(MasterCheck, "Codefuncs");
#pragma CODE_SECTION(SpeedCheck, "Codefuncs");

#pragma CODE_SECTION(SciaRx_isr, "ramfuncs");
#pragma CODE_SECTION(SciaTx_isr, "ramfuncs");
#pragma CODE_SECTION(ScibRx_isr, "ramfuncs");
#pragma CODE_SECTION(ScibTx_isr, "ramfuncs");
#pragma CODE_SECTION(SpiRx_isr, "ramfuncs");
#pragma CODE_SECTION(SpiTx_isr, "ramfuncs");
#pragma CODE_SECTION(Adc_isr, "ramfuncs");
#pragma CODE_SECTION(T1int_isr, "ramfuncs");
-----------------------------------------------------------------------
=======================================================================
main{
	InitSysCtrl();

	DINT;
	InitPieCtrl();
	IER = 0x0000;
	IFR = 0x0000;
	InitPieVectTable();
	EALLOW;
	PieVectTable.RXAINT = &SciaRx_isr;
	PieVectTable.TXAINT = &SciaTx_isr;

	PieVectTable.RXBINT = &ScibRx_isr;
	PieVectTable.TXBINT = &ScibTx_isr;

	PieVectTable.SPITXINTA = &SpiTx_isr;
	PieVectTable.ADCINT = &Adc_isr;
	PieVectTable.TINT0 = &T1int_isr;
	EDIS;

	MemCopy( &RamfuncsLoadStart, &RamfuncsLoadEnd, &RamfuncsRunStart);
	MemCopy( &econstLoadStart, &econstLoadEnd, &econstRunStart);
	MemCopy( &CodefuncsLoadStart, &CodefuncsLoadEnd,
&CodefuncsRunStart);
	InitFlash();

	InitGpio();
//	InitECan();
//	ECanConfig();
	InitSci();
	InitSpi();
	InitCpuTimers();
	InitAdc();
	Config_ADC_EVA();

	GpioDataRegs.GPDSET.bit.GPIOD0 = 1;
	GpioDataRegs.GPDSET.bit.GPIOD1 = 1;
	
	GpioDataRegs.GPDCLEAR.bit.GPIOD0 = 1;
	GpioDataRegs.GPDCLEAR.bit.GPIOD1 = 1;
		
//	InitXIntrupt();
	for(i=0;i<16;i++){	Receivedata[i] = 0x00;}

// Configure CPU-Timer 0 to interrupt every second:
// 100MHz CPU Freq, 1 second Period (in uSeconds)
//	ConfigCpuTimer(&CpuTimer0, 150, 100000);

	ConfigCpuTimer(&CpuTimer0, 150, 250);// int 250 uS
	StartCpuTimer0();

	PieCtrlRegs.PIECRTL.bit.ENPIE = 1;   // Enable the PIE block
//	PieCtrlRegs.PIEIER6.bit.INTx1=1;   //Enable SPI Rx int
	PieCtrlRegs.PIEIER6.bit.INTx2=1;   //Enable SPI Tx int
	PieCtrlRegs.PIEIER1.bit.INTx6 = 1;	//Enable ADC int
	PieCtrlRegs.PIEIER1.bit.INTx7 = 1;   //Enable Timer0 Int
//	PieCtrlRegs.PIECRTL.bit.ENPIE = 1;   // Enable the PIE block
	PieCtrlRegs.PIEIER9.bit.INTx3=1;     // PIE Group 9, INT3 //Enable SciB Rx
	PieCtrlRegs.PIEIER9.bit.INTx4=1;     // PIE Group 9, INT4 //Enable SciB Tx

	PieCtrlRegs.PIEIER9.bit.INTx1=1;     // PIE Group 9, INT3 //Enable SciB Rx
	PieCtrlRegs.PIEIER9.bit.INTx2=1;     // PIE Group 9, INT4 //Enable SciB Tx

	//	PieCtrlRegs.PIEACK.bit.ACK9 = 1;

	IER |= M_INT1;
	IER |= M_INT6;
	IER |= M_INT9;
	EINT;     // Enable Global Interrupts
-------------------------------------

_____________________________________