DSPRelated.com

programming boot flash on a C6747 board

Started by Jason in TMS320c6x13 years ago 1 reply

I'm currently programming the boot flash on a C6747 EVM board by placing the device in a special boot mode that allows the boot program to be...

I'm currently programming the boot flash on a C6747 EVM board by placing the device in a special boot mode that allows the boot program to be loaded via the C6747's UART/RS232 port. The C6747 rom code somehow sends this to the SPI EPROM (flash?) chip. When this is done, I set the boot mode to be from the SPI EPROM and magically the code boots and runs. That's great, but we're going to be mo...


EDMA Source Index overzise:0xffff

Started by mile in TMS320c6x13 years ago 1 reply

Dear Guys, Thanks your help in advance. Now I met one question about EDMA transfer data as follows. I want to transfer one whole...

Dear Guys, Thanks your help in advance. Now I met one question about EDMA transfer data as follows. I want to transfer one whole column pixels from external memory image (size: 32*98304(R*C) )to internal memory,every pixels takes up2 bytes. I set the following parameters for EDMA: config.opt = 0x00100004 | (Inttcc <


Reading HPIC on dsk6713

Started by mich...@oit.edu in TMS320c6x13 years ago 4 replies

Hi, I am trying to read the HPIC register on the 6713 (dsk board). \ Here is what I am doing on the host side: 1. Setting HCNTL1:0 to 00;...

Hi, I am trying to read the HPIC register on the 6713 (dsk board). \ Here is what I am doing on the host side: 1. Setting HCNTL1:0 to 00; HRW' to 1 (read); HHWIL to 0 (1st read) 2. HCS' goes low and stays that way for both reads 2. HDS1' Tied High, HDS2' used as strobe I am reading off an 8 bit port on the host, as only the bottom 4 bits of the HPIC register are relevant. My ...


The DSP runs at very low speed

Started by Coskun AYYILDIZ in TMS320c6x13 years ago 3 replies

Hi everyone, I am using DM3730 (having C64X+ in it) to run a simple for loop. What I see is that the DSP is running at very very low...

Hi everyone, I am using DM3730 (having C64X+ in it) to run a simple for loop. What I see is that the DSP is running at very very low speed. I am using Blackhawk USB560 BP emulator and EVAL version of CCSv4 (without BIOS). I runnnig the following piece of code. #include #include void main() { int i, s1, s2, t; s1 = time(NULL); for(i = 0; i < 100000000;


Hello world project using TMS320C6472-EVM board

Started by nejm...@gmail.com in TMS320c6x13 years ago

Hello , I tried to run a hello world on TMS320C6472-EVM board using XDS100USB emulator and code composer studio V4 "CCS V4" I debug the...

Hello , I tried to run a hello world on TMS320C6472-EVM board using XDS100USB emulator and code composer studio V4 "CCS V4" I debug the active project; but when I click the run button, this message is appeared "C64XP_0: RTDX: RTDX program mode is JTAG" and it doesn't affich "hello world". I didn't understand where is the problem :in the target configuration or not. So please,could you giv...


Using IMGLIB

Started by Coskun AYYILDIZ in TMS320c6x13 years ago 1 reply

Hi all, I am trying to use the IMGLIB library in my project. I do the following things: 1) I downloaded and installed...

Hi all, I am trying to use the IMGLIB library in my project. I do the following things: 1) I downloaded and installed c64plus-imglib_2_02_00_00.exe in my computer. 2) I linked imglib2.I64P in my project. 3) I created a dummy c file to use "any" imglib function. I chose IMG_sobel_3x3_8(in_image, out_image, cols, rows) and included the header file IMG_sobel_3x3_8.h file. The C file seems...


Problem debugging the C64x+ in OMAP3530

Started by Coskun AYYILDIZ in TMS320c6x13 years ago 10 replies

Hi everyone, I am using ccsv4 and blackhawk usb560 bp emulator to debug a hello_world application on the DSP side of OMAP3530 in beagle...

Hi everyone, I am using ccsv4 and blackhawk usb560 bp emulator to debug a hello_world application on the DSP side of OMAP3530 in beagle board. I have problems debugging. First, in order to release the DSP out of reset, I connected to the ARM side, built the app and hit the debug bug. In the console I saw the following error messages: 1) Trouble Reading Register ETM_ID: Error 0x...


need help regarding DSK c6713 kit

Started by "G.M Laghari" in TMS320c6x13 years ago 1 reply

I am working on a real-time DSP in which three DSK kits each connected with a PC and signal processing will be done on DSK kits.Each DSK kit...

I am working on a real-time DSP in which three DSK kits each connected with a PC and signal processing will be done on DSK kits.Each DSK kit also will be connected with each other then data will be send from one DSK kit to another DSK kit and result will be diplay in MATLAB running on PCs. How can we connect three DSK kits with each other? Do i will need daughter cards for connecting each...


problem with using clock() and printf()

Started by unic...@yahoo.com in TMS320c6x13 years ago 23 replies

Hi,all, when use the following .cmd and .c files, and load the generated .out file, I encountered an error: "Error: Error 0x0000000C/-2044 Error...

Hi,all, when use the following .cmd and .c files, and load the generated .out file, I encountered an error: "Error: Error 0x0000000C/-2044 Error during: Register, Break Point, No breakpoint at 0x00006F60 Trouble Removing Breakpoint with the Action "Terminate Program Execution" at 0x6f60: Error 0x00000008/-1076 Error during: Break Point, Cannot set/verify breakpoint at 0x00006F60" If the pr...


looking for evm board

Started by gone...@yahoo.com in TMS320c6x13 years ago 1 reply

Hola all i am looking for a EVM board , which has PCI 2040 bridge chip on . Kindly plz provide the link and anyother better...

Hola all i am looking for a EVM board , which has PCI 2040 bridge chip on . Kindly plz provide the link and anyother better alternative thanx Waiting for a reply Grt day all _____________________________________


Ask a Question to the DSPRelated community

To significantly increase your chances of receiving answers, please make sure to:

  1. Use a meaningful title
  2. Express your question clearly and well
  3. Do not use this forum to promote your product, service or business
  4. Write in clear, grammatical, correctly-spelled language
  5. Do not post content that violates a copyright