AD535 | BIOS | Booting | Bootloader | C621 | C6211 | C6415 | C671 | C6711 | C6711DSK | C6713 | CCS | Chassaing | COFF | DAT | DM64 | DM642 | DMA | DSK671 | DSK6711 | EDM | EDMA | EMIF | Emulator | EVM | EVM620 | FFT | FIR | GPIO | Halting | HPI | HWI | IDK | JTAG | LDB | LDH | LDW | Linker | LMS | LOG_printf | Matlab | McBSP | MEM_alloc | MIPS | PCI | PCM3003 | Pipeline | Profiling | QDM | Reset | ROM | RTDX | Sampling | SDRAM | Stack | TEB | THS1206 | TMS320C621 | TMS320C6416 | TMS320C6711 | TMS320C6713 | UART | Vector Table | XBUS | XDS560

Hi Folks,

My organization just purchased a new DM6446 EVM from spectrum digital. 
They told that this board supports their old XDS510USB JTAG which we 
already possess. But the MSP340 JTAG JTAG connector of the EVM does not 
match the JTAG connector we have of XDS510USB.

So my query is:

1. Doses this board at all supports the XDS510USB JTAG?
2. As you already know JTAG is a very costly hardware so can you suggest 
me any way out of this trouble?

Thanking you all in advance,

-- 
With Regards,
Nilanjan Goswami.

Check Out Industry's First Single-Chip, Multi-Format, Real-Time HD Video Transcoding Solution
for Commercial & Consumer End Equipment: www.ti.com/dm6467

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

Hi Nilanjan,

You might want to ask Spectrum Digital about a small adapter board that they
designed to connect 2x7 0.1' emulator connector to 2x10 0.05' Davinci JTAG
connector on the EVM. Regarding MSP430, it uses the same 2x7 0.1' connector,
but you might need an adapter as well, because pins on the xds510 might not
correspond to the signals on the MSP430 JTAG connector; you will need to check
this. Again, ask Spectrum Digital's support. You might also want to ask some 
help from your local hardware engineers. (I asked my colleagues and they
helped me a lot! :)

I use an xds510 emulator (www.sauris.de) with an adapter to debug Davinci and 
it works reasonably fine.

Rgds,

Andrew

> Subject: JTAG Problem for DM6446
> Posted by: "Nilanjan Goswami" n...@cal.interrasystems.com nilanjangoswami
> Date: Fri Feb 29, 2008 4:24 am ((PST))
>
> Hi Folks,
>
> My organization just purchased a new DM6446 EVM from spectrum digital.
> They told that this board supports their old XDS510USB JTAG which we
> already possess. But the MSP340 JTAG JTAG connector of the EVM does not
> match the JTAG connector we have of XDS510USB.
>
> So my query is:
>
> 1. Doses this board at all supports the XDS510USB JTAG?
> 2. As you already know JTAG is a very costly hardware so can you suggest
> me any way out of this trouble?
>
> Thanking you all in advance,
>
> -- 
> With Regards,
> Nilanjan Goswami.
>
Check Out Industry's First Single-Chip, Multi-Format, Real-Time HD Video Transcoding Solution
for Commercial & Consumer End Equipment: www.ti.com/dm6467

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

Nilanjan,

On Sat, Mar 1, 2008 at 8:31 AM, Andrew Nesterov
<a...@techemail.com> wrote:

>  Hi Nilanjan,
>
>  You might want to ask Spectrum Digital about a small adapter board that
> they
>  designed to connect 2x7 0.1' emulator connector to 2x10 0.05' Davinci JTAG
>  connector on the EVM. Regarding MSP430, it uses the same 2x7 0.1'
> connector,
>  but you might need an adapter as well, because pins on the xds510 might not
>  correspond to the signals on the MSP430 JTAG connector; you will need to
> check
>  this.

FYI - ask far as I know, the MSP430 is in another universe.  The last
time that debugged an MSP430 system, I needed a separate emulator and
debugger software.

mikedunn

> Again, ask Spectrum Digital's support. You might also want to ask
> some
>  help from your local hardware engineers. (I asked my colleagues and they
>  helped me a lot! :)
>
>  I use an xds510 emulator (www.sauris.de) with an adapter to debug Davinci
> and
>  it works reasonably fine.
>
>  Rgds,
>
>  Andrew
>
>  > Subject: JTAG Problem for DM6446
>  > Posted by: "Nilanjan Goswami" n...@cal.interrasystems.com
> nilanjangoswami
>  > Date: Fri Feb 29, 2008 4:24 am ((PST))
>
>  >
>  > Hi Folks,
>  >
>  > My organization just purchased a new DM6446 EVM from spectrum digital.
>  > They told that this board supports their old XDS510USB JTAG which we
>  > already possess. But the MSP340 JTAG JTAG connector of the EVM does not
>  > match the JTAG connector we have of XDS510USB.
>  >
>  > So my query is:
>  >
>  > 1. Doses this board at all supports the XDS510USB JTAG?
>  > 2. As you already know JTAG is a very costly hardware so can you suggest
>  > me any way out of this trouble?
>  >
>  > Thanking you all in advance,
>  >
>  > --
>  > With Regards,
>  > Nilanjan Goswami.
>  >
>  

-- 
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
Check Out Industry's First Single-Chip, Multi-Format, Real-Time HD Video Transcoding Solution
for Commercial & Consumer End Equipment: www.ti.com/dm6467

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )