Fwd: Connecting between C6713 DSK HPI and HyperTerminal | TMS320C6x

Oops, I failed to copy the group.

mikedunn

Omnia,

On 6/11/08, omnia.mostafa21 <o...@yahoo.com> wrote:
> mikedunn,
>
> first of all, thanks for your reply
>
> My Grad Project is a Speech Recognition One, I convert the Voice into
> Text.
> to display the text , I'll use the HyperTerminal.
> i didn't know haw can i do that using the Kit directly .. by search i
> found a IEEE paper .. the author had solve this Problem using that HW
> (TMS320C6713 dsk HPI Daughtercard).. and a print screen for the output
> on the HyperTerminal was include on that paper ..
>
> and the Authors ( developers) established site for the DSP :
> http://www.educationaldsp.com/stockproduct_dsk6xxxhpi.htm
>
> So, i'm working in that part depending on that research.
> _ Yes, I send ASCII for the HyperTerminal (the word)
>
> _ the Program i'm trying to Run .. suppose to display the character
> (1) on the HyperTerminal ..

1. Are you running an example program that was provided by eDSP??
If not, I suggest that you run and understand the examples before you
try to do anything else.
> _ when i'm trying to Connect the CCS to the Kite while the HPI is
> connect .. it's give an error msg , the there is NO Target connect
> once i disconnect the HPI .. the CCS connect .

2. Did you install the 2 pin power connector on your DSK??
If yes, does the LED blink with the operating mode??

>
> _ i don't know if there another way to display the output (Words) from
> the DSP on my PC .

3. There are 2 ways to perform your output - 'push' the output from
the DSP [DSP Services] or 'pull' the output from the PC [Host
Services]. The documentation looks like DSP Services [what it sounds
like you are planning to use] will be limited to about 4 K chars/sec.

BTW, since I have had a few questions on eDSP and did some
investigation.  The owner of the company is very much a 'good guy' and
has been very active in making DSPs more usable to students since the
6211 DSK came out several years ago.  Judging from the providing
documentation, I have great confidence that the provided software will
work well for its intended use.  I mention this because there some
products out there that provide very little useful
software/documentation.
[This reflects my personal opinion and I am not affiliated with eDSP].

mikedunn
>
> i'll be grateful  if someone help me in that
>
> Thanks in advanced ..
>
> Omnia M.
> --- In c...@yahoogroups.com, "Michael Dunn" <mike.dunn.001@...> wrote:
> >
> > Omnia,
> >
> > On 6/11/08, omnia.mostafa21 <omnia.mostafa21@...> wrote:
> > >
> > >   Hi All,
> > >
> > > I have a DSP C6713DSK and its HPI DaughterCard .. i want to read from
> > > the USB on the HyperTerminal .
> > >
> >
> > I have never used this daughtercard [I am not sure who made it].
> >
> > The manufacturer should have provided information [and ideally one
> or more
> > example programs] on the data format that is required to be sent to the
> > endpoint buffer [or details on a higher level protocol if that is
> used] to
> > implement memory reads and writes.
> >
> > I think that the HyperTerminal only sends/receives ASCII data which
> might be
> > a problem.
> >
> > Check your documentation and post the HPI/USB daughtercard
> manufacturer so
> > that maybe someone else with the same board might help.
> >
> >
> >
> >    The CCS 3.3 can't connect with the DSK while the HPI is connected to
> > > it, even if its enable switch is off.
> > >
> >
> > I don't understand this. I cannot think of any reason that CCS
> should not
> > connect with the HPI/USB board in place [unless there is something wrong
> > with it].
> >
> >    in the Instruction .. the steps is :
> > > 1. Download the program using CCS, but do not run.
> > > 2. Press and release the reset button on the DSK6713HPI daughtercard.
> > > 3. Run the program from CCS.
> > >
> >
> > What program are you downloading??  What is it supposed to do??
> >
> >    but it's not executable .. i don't know where is the problem ?!!
> > >
> >
> > What does this mean?? Do you get some error message??
> >
> > mikedunn
> >
> >
> >
> >    would anyone kindly tell me how can i read from the HPI (USB) on th
> > > HyperTerminal ??
> > >
> > > Thanks in advanced ..
> > >
> > > Omnia Mostafa.
> > >
> > >
> > >
> >
> >
> >
> > --
> > www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
> 

--
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
-- 
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php

------------------------------------

OMAP35x EVM jump-starts low-power apps
------------------------------------
The modular and extensible OMAP35x Evaluation Module (EVM) enables developers to start building
applications based on the OMAP35x architecture:http://www.DSPRelated.com/omap35x
(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )
Sign in

Search c6x

Subscribe to c6x

c6x by Keywords

Discussion Groups

Discussion Groups | TMS320C6x | Fwd: Connecting between C6713 DSK HPI and HyperTerminal

Fwd: Connecting between C6713 DSK HPI and HyperTerminal - Michael Dunn - Jun 11 18:41:44 2008
