AD535 | BIOS | Booting | Bootloader | C621 | C6211 | C6415 | C671 | C6711 | C6711DSK | C6713 | CCS | Chassaing | COFF | DAT | DM64 | DM642 | DMA | DSK671 | DSK6711 | EDM | EDMA | EMIF | Emulator | EVM | EVM620 | FFT | FIR | GPIO | Halting | HPI | HWI | IDK | JTAG | LDB | LDH | LDW | Linker | LMS | LOG_printf | Matlab | McBSP | MEM_alloc | MIPS | PCI | PCM3003 | Pipeline | Profiling | QDM | Reset | ROM | RTDX | Sampling | SDRAM | Stack | TEB | THS1206 | TMS320C621 | TMS320C6416 | TMS320C6711 | TMS320C6713 | UART | Vector Table | XBUS | XDS560

Hi Claudio

Thanks for posting this qs because I have just met the same prob with the C6414.
I was wondering if you have found the drivers by getting the specific C6713 CC studio CDs that
Matt has told you?

Thanks
Ivan
>  Hi everybody,  
>I'm new in this group and I need some help...  
>I have no experience in programming dsp but now I have to do it for my  
>thesis and I have a problem.  
>  
>I have a TMS320C6713 DSK board from Spectrum Digital that can be  
>connected to the pc using USB port.  
>I read the Quick Start Installation Guide and I followed the  
>instruction but I couldn't be able to connect the board to the pc.  
>  
>Actually I found on the kit only 2 cds:  
>1. Matlab and Simulink for use with TI DSPs (free 30-day Trial)  
>2. TI Product Information - eXpressDSP - Software and Development Tools  
>I read on the Quick Start Installation Guide that there must be also  
>the C6713 DSK CodeComposerStudio CDROM, but I didn't find it.  
>Luckily I found a CodeComposerStudio v3.0 at my university department  
>and I installed it.  
>Everything seemed to go well but when I connect the USB cable into the  
>DSK board, the pc didn't find the driver on the CCS v3.0 CDROM.  
>So the pc canot recognize the DSK board. I read that the driver files  
>are "sdusbemu.inf" and sdusbemu.sys" but I didn't find them on the CDROM.  
>  
>Anybody had this problem? Can you suggest me how to fix it or where to  
>find the driver's file?  
>  
>Thank you for your help  
>Claudio  
>  
>  
>  
>  
>  
>  
>  
>     

------------------------------------

OMAP35x EVM jump-starts low-power apps
------------------------------------
The modular and extensible OMAP35x Evaluation Module (EVM) enables developers to start building
applications based on the OMAP35x architecture:http://www.DSPRelated.com/omap35x

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

Ivan,

DSKs should ship with a special DSK version of CCS.  As far as I know, the
only place to get the CD is from the manufacturer.
http://www.spectrumdigital.com/

If you purchased a new DSK, contact the distributor/authorized reseller.
If you purchased it used, you might try contacting SD if you have the
original box [with the part number label].

mikedunn
On 6/26/08, g...@yahoo.co.uk <g...@yahoo.co.uk> wrote:
>
>   Hi Claudio
>
> Thanks for posting this qs because I have just met the same prob with the
> C6414.
> I was wondering if you have found the drivers by getting the specific C6713
> CC studio CDs that Matt has told you?
>
> Thanks
> Ivan
>
> > Hi everybody,
> >I'm new in this group and I need some help...
> >I have no experience in programming dsp but now I have to do it for my
> >thesis and I have a problem.
> >
> >I have a TMS320C6713 DSK board from Spectrum Digital that can be
> >connected to the pc using USB port.
> >I read the Quick Start Installation Guide and I followed the
> >instruction but I couldn't be able to connect the board to the pc.
> >
> >Actually I found on the kit only 2 cds:
> >1. Matlab and Simulink for use with TI DSPs (free 30-day Trial)
> >2. TI Product Information - eXpressDSP - Software and Development Tools
> >I read on the Quick Start Installation Guide that there must be also
> >the C6713 DSK CodeComposerStudio CDROM, but I didn't find it.
> >Luckily I found a CodeComposerStudio v3.0 at my university department
> >and I installed it.
> >Everything seemed to go well but when I connect the USB cable into the
> >DSK board, the pc didn't find the driver on the CCS v3.0 CDROM.
> >So the pc canot recognize the DSK board. I read that the driver files
> >are "sdusbemu.inf" and sdusbemu.sys" but I didn't find them on the
CDROM.
> >
> >Anybody had this problem? Can you suggest me how to fix it or where to
> >find the driver's file?
> >
> >Thank you for your help
> >Claudio
> >
> >
> >
> >
> >
> >
> >
> >

-- 
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )