AD535 | BIOS | Booting | Bootloader | C621 | C6211 | C6415 | C671 | C6711 | C6711DSK | C6713 | CCS | Chassaing | COFF | DAT | DM64 | DM642 | DMA | DSK671 | DSK6711 | EDM | EDMA | EMIF | Emulator | EVM | EVM620 | FFT | FIR | GPIO | Halting | HPI | HWI | IDK | JTAG | LDB | LDH | LDW | Linker | LMS | LOG_printf | Matlab | McBSP | MEM_alloc | MIPS | PCI | PCM3003 | Pipeline | Profiling | QDM | Reset | ROM | RTDX | Sampling | SDRAM | Stack | TEB | THS1206 | TMS320C621 | TMS320C6416 | TMS320C6711 | TMS320C6713 | UART | Vector Table | XBUS | XDS560

Ivan,

I use some different emulators, but not Spectrum Digital.

see comments below.

On Thu, Jul 10, 2008 at 8:08 AM, Ivan <g...@yahoo.co.uk> wrote:
> Hi Mike,
>
> I would like to ask something that has bothered me for a while and
> has been hindering me from progressing my project.
>
> Previously, when I used the Code Composer Studio v 3.1 I could use
> the USB jtag emulator built into the 6416T board instead of buying
> the real emulator, and for this to work was due to the fact that the
> driver and the neccessary XML file was already installed, in these
> locations:
>
> C:\CCStudio_V3.1\drivers\import\dsk6416.ccs
> C:\CCStudio_V3.1\drivers\TargetDB\drivers\sdgo6416dsk_11.xml
>
<mld>
You may need to copy another file - I don't know which one, but
someone who has done this may help.
>
> I've been trying to add these files into the same directory
> locations but for the CCStudio v3.3, because I also want to emulate
> using USB jtag emulator but with the higher version of CC, and
> currently CC v3.3 doesn't have instaled the neccessary 'board'
> listed in its setup window. The pdfs told me to copy the files and
> import them in the CC setup. I was able to File->import the above
> copied files. However I get this error after closing the setup and
> starting up CC:
>
> Error initializing emulator
>
> I/O Port = 540
>
> Board Name: DSK6416
> Cpu Name: DSP_C64xx
>
> Abort:          Close Code Composer Studio.
> Retry:          Try to initialize the emulator again.
> Ignore:         Ignore the initialization error and start
>                potentially without target debugging access.
> Diagnostic:     Run diagnostic utility.
>
> which means I couldn't connect.
>
> I have seen many people in this forum who have the same error but
> their causes are very different. Is there something I have forgotten
> to do?

<mld>
SD may have updated their drivers from CCS 3.1 to 3.3. Check their
website for updates.

Does SDconfig run?? [their 'diagnostic utility']

If all else fails, you can:
1. Configure CCS 3.1, save the configuration, and copy the
/cc/bin/brddat/ccbrd0.dat text] file.
2. Configure CCS 3.3, save the configuration, and copy the
/cc/bin/brddat/ccbrd0.dat text] file.
3. Check the file differences.

Please post your questions to the group, not me directly

mikedunn

>
> Thanks
> Ivan

-- 
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )