Sign in
Search c6x
Subscribe to c6x
c6x by Keywords
AD535 | BIOS | Booting | Bootloader | C621 | C6211 | C6415 | C671 | C6711 | C6711DSK | C6713 | CCS | Chassaing | COFF | DAT | DM64 | DM642 | DMA | DSK671 | DSK6711 | EDM | EDMA | EMIF | Emulator | EVM | EVM620 | FFT | FIR | GPIO | Halting | HPI | HWI | IDK | JTAG | LDB | LDH | LDW | Linker | LMS | LOG_printf | Matlab | McBSP | MEM_alloc | MIPS | PCI | PCM3003 | Pipeline | Profiling | QDM | Reset | ROM | RTDX | Sampling | SDRAM | Stack | TEB | THS1206 | TMS320C621 | TMS320C6416 | TMS320C6711 | TMS320C6713 | UART | Vector Table | XBUS | XDS560
Discussion Groups
Discussion Groups | TMS320C6x | CCS Bring up through JTAG for C6415
Technical discussions about the TI C6000 DSPs (including the c62x, c64x and c67x DSPs).
CCS Bring up through JTAG for C6415 - gururajb2 - Apr 24 4:20:00 2003
|
hi all, I am facing problem in bringing up CCS through JTAG for C6415 .Since all conections to JTAG header is less than 6 inchs i am not using any signal buffering. Pls inform any other precautions are to be taken for JTAG. Thanks in advance. -- gururaj |
|
|
(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )
CCS Bring up through JTAG for C6415 - gururajb2 - Apr 24 5:11:00 2003
|
hi, I am using customized C6415 board for some product.I am using JTAG for debugging.We made Following connections for JTAG header and DSP 1.TRST is pulled down and connected to DSP and Header 2.4,8,10,12 pins of JTAG header is conneced to GROUND. 3.12 and 13 pins of Header is puuled up and connected to DSP EMU0 and EMU1 pins 4.TCK_RET and TCK(9 and 10 pins of Header)shorted and connected DSP respective pins 5.TDI and TDO (3 aND 7 PINS of Header)pulled up and connected to DSPs respective pins. 6.TMS (pin no 1 of header) is directly connected to DSP. But we r not able bring up CCS through JTAG emulator.Pls inform me if any problem in the above hardware connections and also send u r comments. Thanks in advance. -- gururaj |
(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )
RE: CCS Bring up through JTAG for C6415 - Gabriel Drenger - May 14 6:09:00 2003
|
We had the same problem . The problem was the change of the DSP silicon revision from 1.03 to 1.1 - we had to change the CCS 2.12 driver Gabriel Drenger -----Original Message----- From: gururajb2 [mailto:] Sent: Thursday, April 24, 2003 6:21 AM To: Subject: [c6x] CCS Bring up through JTAG for C6415 hi all, I am facing problem in bringing up CCS through JTAG for C6415 .Since all conections to JTAG header is less than 6 inchs i am not using any signal buffering. Pls inform any other precautions are to be taken for JTAG. Thanks in advance. -- gururaj _____________________________________ |
(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )