Sign in

username:

password:



Not a member?

Search c6x



Search tips

Subscribe to c6x



c6x by Keywords

AD535 | BIOS | Booting | Bootloader | C621 | C6211 | C6415 | C671 | C6711 | C6711DSK | C6713 | CCS | Chassaing | COFF | DAT | DM64 | DM642 | DMA | DSK671 | DSK6711 | EDM | EDMA | EMIF | Emulator | EVM | EVM620 | FFT | FIR | GPIO | Halting | HPI | HWI | IDK | JTAG | LDB | LDH | LDW | Linker | LMS | LOG_printf | Matlab | McBSP | MEM_alloc | MIPS | PCI | PCM3003 | Pipeline | Profiling | QDM | Reset | ROM | RTDX | Sampling | SDRAM | Stack | TEB | THS1206 | TMS320C621 | TMS320C6416 | TMS320C6711 | TMS320C6713 | UART | Vector Table | XBUS | XDS560

Discussion Groups

Discussion Groups | TMS320C6x | Install JTAG??

Technical discussions about the TI C6000 DSPs (including the c62x, c64x and c67x DSPs).

  

Post a new Thread

Install JTAG?? - dibyendu mondal - Feb 10 16:24:00 2005




Hi all

Today I get JTAG xds510pp_plus but I have find a problem to install it.

I have the system:
______________
|C6x DSP board |<----- Printer port ----->PC and the new one:
______________
|C6x DSP board | (<---) JTAG Interface(??) --- Printer port ----->PC(??)

so have I use 2 Printer port to connect JTAG,DSP and PC ?

DSP <--->JTAG
\ /
\ /
? PC ?

or I should disconnect the Printer port connection from DSP ?

Suggest me please Thanking you
Regards
Dibyendu Mondal





(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

Re: Install JTAG?? - Mike Dunn - Feb 10 21:44:00 2005

Dibyendu,
 
I am not sure if you have 1 or 2 DSP boards...
 
If you have only 1 and it is a 6711 DSK-
For using CCS only you need
PC_par_port->xds510pp_plus->dsp_board.
 
If you are using a windoze program to communicate with the DSK through HPI, you can use your original setup only [the xds510pp_plus does have better performance]
or you must use 2 par ports
PC_par_port_1->dsp_board [HPI]
PC_par_port_2->xds510pp_plus->dsp_board [JTAG]
When you hook up the pp_plus to the JTAG connector, it will disable the CCS/JTAG connection on port 1.
 
If you you have two DSP boards, then you will need 2 parallel ports [or purchase a USB or PCI emulator].
 
mikedunn

dibyendu mondal <d...@yahoo.co.in> wrote:


Hi all

Today I get JTAG xds510pp_plus but I have find a problem to install it.

I have the system:
______________
|C6x DSP board |<----- Printer port ----->PCand the new one:
______________
|C6x DSP board | (<---) JTAG Interface(??) --- Printer port ----->PC(??)

so have I use 2 Printer port to connect JTAG,DSP and PC ?

DSP <--->JTAG
\ /
\ /
? PC ?

or I should disconnect the Printer port connection from DSP ?

Suggest me pleaseThanking you
Regards
Dibyendu Mondal

<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/c6x/

<*> To unsubscribe from this group, send an email to:
c...@yahoogroups.com

<*





(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )