AD535 | BIOS | Booting | Bootloader | C621 | C6211 | C6415 | C671 | C6711 | C6711DSK | C6713 | CCS | Chassaing | COFF | DAT | DM64 | DM642 | DMA | DSK671 | DSK6711 | EDM | EDMA | EMIF | Emulator | EVM | EVM620 | FFT | FIR | GPIO | Halting | HPI | HWI | IDK | JTAG | LDB | LDH | LDW | Linker | LMS | LOG_printf | Matlab | McBSP | MEM_alloc | MIPS | PCI | PCM3003 | Pipeline | Profiling | QDM | Reset | ROM | RTDX | Sampling | SDRAM | Stack | TEB | THS1206 | TMS320C621 | TMS320C6416 | TMS320C6711 | TMS320C6713 | UART | Vector Table | XBUS | XDS560

I am using the Imaging Development Kit (IDK) from TI but I have the
following problem,when I tray to run the loaded project to the
TMS320C6711 IDK I got nothing on the screen connected to the IDK, and
when I halt the processor I got the following message

"
Trouble Halting Target CPU
Error 0x80000020/-1070
Fatal Error during Execution
An unknown error prevented the emulator from accessing the processor
in a timely fashion It is recommended to RESET EMULATOR. This will
disconnect each target from the emulator The targets should then be
power cycled or hard reset followed by an emureset and reconnect to
each target_ I have to reset all the system , and reload the project then reload &
Run , sometimes I have to do that for many times and sometimes I got
the result from the first try.
Any Help?



(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

It sounds like your program has run away to somewhere bad. I would make the
program smaller and smaller, until it works. Then add things back in. Also,
if that does not work, maybe there are some register or EMIF settings that
are not correct.

Regards,

Robert

> -----Original Message-----
> From: c6x@c6x@... [mailto:c6x@c6x@...] On
> Behalf Of aganoun
> Sent: Friday, November 25, 2005 8:26 AM
> To: c6x@c6x@...
> Subject: [c6x] Problem with IDK
>
> I am using the Imaging Development Kit (IDK) from TI but I
> have the following problem,when I tray to run the loaded
> project to the
> TMS320C6711 IDK I got nothing on the screen connected to the
> IDK, and when I halt the processor I got the following message
>
> "
> Trouble Halting Target CPU
> Error 0x80000020/-1070
> Fatal Error during Execution
> An unknown error prevented the emulator from accessing the
> processor in a timely fashion It is recommended to RESET
> EMULATOR. This will disconnect each target from the emulator
> The targets should then be power cycled or hard reset
> followed by an emureset and reconnect to each target_ > I have to reset all the system , and reload the project then
> reload & Run , sometimes I have to do that for many times and
> sometimes I got the result from the first try.
> Any Help? >
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.362 / Virus Database: 267.13.8/184 - Release
> Date: 11/27/2005
--
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.1.362 / Virus Database: 267.13.8/184 - Release Date: 11/27/2005





(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )