AD535 | BIOS | Booting | Bootloader | C621 | C6211 | C6415 | C671 | C6711 | C6711DSK | C6713 | CCS | Chassaing | COFF | DAT | DM64 | DM642 | DMA | DSK671 | DSK6711 | EDM | EDMA | EMIF | Emulator | EVM | EVM620 | FFT | FIR | GPIO | Halting | HPI | HWI | IDK | JTAG | LDB | LDH | LDW | Linker | LMS | LOG_printf | Matlab | McBSP | MEM_alloc | MIPS | PCI | PCM3003 | Pipeline | Profiling | QDM | Reset | ROM | RTDX | Sampling | SDRAM | Stack | TEB | THS1206 | TMS320C621 | TMS320C6416 | TMS320C6711 | TMS320C6713 | UART | Vector Table | XBUS | XDS560

I need an emulator for 6713. What I want is a particular emulator which is
able to show me all pins in order to test my daugther card because I'm not sure
of the particular function of each pinout.
Thank you.

______________________________
Start your Android Ice Cream Sandwich development on TI's AM35x Sitara ARM Cortex-A8 processor today.



(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

giuseppe,
 
see comments below.
----- Original Message ----
From: g...@libero.it
To: c...@yahoogroups.com
Sent: Monday, July 3, 2006 9:28:28 AM
Subject: [c6x] Emulator for 6713
I need an emulator for 6713. What I want is a particular emulator which is able
to show me all pins in order to test my daugther card because I'm not sure of
the particular function of each pinout.
Emulators for TI DSPs are all basically the same.  They fall into 2 classes,
XDS510 [basic emulation, low to moderately priced] and XDS560 [faster and more
expensive, supports HS-RTDX, upgradeable to support new features].
The emulators provide basic debugging [hw & sw breakpoints, step, run,
halt], memory and register access, and access to advanced emulation hardware
features on devices that support it.  Any additional debugging features, like
profiling, are built on top of these capabilities.
W.R.T. the daughtercard pin functionality, there is no subtitute for
understanding the DSP data sheet and the schematics of the host card [most of
the daughtercard pins are just buffered signals directly from the DSP.  The only
way that I know to troubleshoot these signals is with a logic analyzer or scope.
 I am sure that if you run into problems with a specific signal or set of
signals that someone will be able to help you.
mikedunn

Thank you. 
 

______________________________
Start your Android Ice Cream Sandwich development on TI's AM35x Sitara ARM Cortex-A8 processor today.



(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

thank you for the reply. Maybe I have been not very clear. The problem is
that I'm projecting a daugther card and what I want is a simulator (like Matlab
or something else) which is able to rapesent all my components (all DSP pin and
other component) in order to simulate my entire project before to do it.

thank you

______________________________
New Code Sharing Section now Live on DSPRelated.com. Learn about the Reward Program for Contributors here.



(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

Guiseppe-

> thank you for the reply. Maybe I have been not very clear. The problem is
> that I'm projecting a daugther card and what I want is a simulator (like
> Matlab or something else) which is able to rapesent all my components
> (all DSP pin and other component) in order to simulate my entire project
> before to do it.

Can MATLAB DSK board simulations include an arbitrary "EMIF port"
block? 
An arbitrary "McBSP port" block?  If so then maybe you can do
something
along the lines of what you're looking for.

In any case, this sounds like a great introduction for you to the real
world of engineering.  If it was easy and everything could be simulated
then anyone could do it!  But it's not.  Many times DSP engineers end up
in the lab with scope and analyzer trying to figure things out, as Mike
indicated.  Hope you like lab work :-)

-Jeff

______________________________
New Code Sharing Section now Live on DSPRelated.com. Learn about the Reward Program for Contributors here.



(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

thank you for the reply. Maybe I have been not very clear. The problem is
that I'm projecting a daugther card and what I want is a simulator (like Matlab
or something else) which is able to rapesent all my components (all DSP pin and
other component) in order to simulate my entire project before to do it.

thank you

______________________________
New Code Sharing Section now Live on DSPRelated.com. Learn about the Reward Program for Contributors here.



(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )