AD535 | BIOS | Booting | Bootloader | C621 | C6211 | C6415 | C671 | C6711 | C6711DSK | C6713 | CCS | Chassaing | COFF | DAT | DM64 | DM642 | DMA | DSK671 | DSK6711 | EDM | EDMA | EMIF | Emulator | EVM | EVM620 | FFT | FIR | GPIO | Halting | HPI | HWI | IDK | JTAG | LDB | LDH | LDW | Linker | LMS | LOG_printf | Matlab | McBSP | MEM_alloc | MIPS | PCI | PCM3003 | Pipeline | Profiling | QDM | Reset | ROM | RTDX | Sampling | SDRAM | Stack | TEB | THS1206 | TMS320C621 | TMS320C6416 | TMS320C6711 | TMS320C6713 | UART | Vector Table | XBUS | XDS560

Hi, I use a C6713 DSPor and CCS 2.21. When using DSP/BIOS config, I found I
can't set up DMA channel.

If I right click "DMA_channel0" in "DMA Resource Manager", and choose
"Properties", the "Open DMA Channel" checkbox is gray. If I insert a new
dmaCfg in "DMA Configuration Manager", all options (except the "add
comments" option) of the newly added dmaCfg are gray. Could somebody tell me
why? Thank you.

Xuchen

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

Got the answer, C6713 has no DMA. What a mistake;-)

Xuchen

  _____  

From: c...@yahoogroups.com [mailto:c...@yahoogroups.com] On Behalf Of
yaoxuchen
Sent: Sunday, July 01, 2007 8:54 AM
To: c...@yahoogroups.com
Subject: [c6x] Can't check the "Open DMA Channel" option in DSP/BIOS config

Hi, I use a C6713 DSPor and CCS 2.21. When using DSP/BIOS config, I found I
can't set up DMA channel.

If I right click "DMA_channel0" in "DMA Resource Manager", and choose
"Properties", the "Open DMA Channel" checkbox is gray. If I insert a new
dmaCfg in "DMA Configuration Manager", all options (except the "add
comments" option) of the newly added dmaCfg are gray. Could somebody tell me
why? Thank you.

Xuchen

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

open the settings of CCS 2.0, and check if you really selected the C6713.
You must have set another processor, that has no DMA.
Check also that you use the XDS560 driver.

Regards

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

Xu Chen-

> Got the answer, C6713 has no DMA. What a mistake;-)

C6x device with no DSP?  TI couldn't sell too many of those!

Go to this page:

  http://focus.ti.com/docs/prod/folders/print/tms320c6713.html

and look for:

  o Enhanced Direct-Memory-Access (EDMA) Controller
   (16 Independent Channels)

-Jeff

>   _____
>
> From: c...@yahoogroups.com [mailto:c...@yahoogroups.com] On Behalf Of
> yaoxuchen
> Sent: Sunday, July 01, 2007 8:54 AM
> To: c...@yahoogroups.com
> Subject: [c6x] Can't check the "Open DMA Channel" option in DSP/BIOS config
>
> Hi, I use a C6713 DSPor and CCS 2.21. When using DSP/BIOS config, I found I
> can't set up DMA channel.
>
> If I right click "DMA_channel0" in "DMA Resource Manager", and choose
> "Properties", the "Open DMA Channel" checkbox is gray. If I insert a
new
> dmaCfg in "DMA Configuration Manager", all options (except the "add
> comments" option) of the newly added dmaCfg are gray. Could somebody tell me
> why? Thank you.
>
> Xuchen

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )

Oh, Sorry. I mean C6713 has no DMA devices but EDMA devices. So I can check
the "Open EDMA Channel" option but can't check the "Open DMA Channel"
option.

Thank you for your link!

Xuchen

-----Original Message-----
From: Jeff Brower [mailto:j...@signalogic.com] 
Sent: Monday, July 02, 2007 11:56 PM
To: Yao Xu Chen
Cc: c...@yahoogroups.com
Subject: RE: [c6x] Can't check the "Open DMA Channel" option in DSP/BIOS
config

Xu Chen-

> Got the answer, C6713 has no DMA. What a mistake;-)

C6x device with no DSP?  TI couldn't sell too many of those!

Go to this page:

  http://focus.ti.com/docs/prod/folders/print/tms320c6713.html

and look for:

  o Enhanced Direct-Memory-Access (EDMA) Controller
   (16 Independent Channels)

-Jeff

>   _____
>
> From: c...@yahoogroups.com [mailto:c...@yahoogroups.com] On Behalf Of
> yaoxuchen
> Sent: Sunday, July 01, 2007 8:54 AM
> To: c...@yahoogroups.com
> Subject: [c6x] Can't check the "Open DMA Channel" option in DSP/BIOS
config
>
> Hi, I use a C6713 DSPor and CCS 2.21. When using DSP/BIOS config, I found
I
> can't set up DMA channel.
>
> If I right click "DMA_channel0" in "DMA Resource Manager", and choose
> "Properties", the "Open DMA Channel" checkbox is gray. If I insert a
new
> dmaCfg in "DMA Configuration Manager", all options (except the "add
> comments" option) of the newly added dmaCfg are gray. Could somebody tell
me
> why? Thank you.
>
> Xuchen

(You need to be a member of c6x -- send a blank email to c6x-subscribe@yahoogroups.com )