56303 | 563xx | 5680 | 56805 | 5680x | 56F80 | 56F800DEMO | 56F805 | 56f807 | 56F830 | ADC | Bootloader | Codec | CodeWarrior | CW5 | CW6 | Debugger | DSP56303 | DSP56303EVM | DSP563xx | DSP5680 | DSP56800 | DSP56807 | DSP56858 | DSP56858EVM | DSP56F803 | DSP56F805 | DSP56F807 | DSP56F80x | DSP56F826 | DSP56F827 | DSP56F8xx | EVM | FFT | Flash_over_jtag | GPIO | Interrupt | Interrupts | JTAG | LCD | Linker | MCF5307 | Metrowerks | Modulus | MSCAN | PCMaster | PWM | Quad | Rif | RTOS | SDK | SPI

Trying to retarget from RAM to FLASH. CW IDE doesnt give me a choice of Flash (Ram doesnt show up either, just M56800) I mucked around a bit. Started new projects etc.. in order to hit on a combo that would give me the choice of FLASH but it didnt happen. I went thru some documentation from the starter class motorola gave, resetting jumpers on the evm etc but still couldnt retarget. Followed the advice of a couple of guys that were nice enough to respond. Still no dice. Using CW ver 3.5, IDE ver 4.06 Happy developing Joe McCarron

(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )

Have you installed SDK 2.3 for DSP56800. If you use SDK stationery, I am sure it gives you two choices: External RAM or Flash. C.W. --- Joe McCarron <> wrote: > Trying to retarget from RAM to FLASH. CW IDE doesnt > give me a choice of Flash (Ram doesnt show up > either, just > M56800) I mucked around a bit. Started new projects > etc.. in > order to hit on a combo that would give me the > choice of FLASH > but it didnt happen. > > I went thru some documentation from the starter > class motorola > gave, resetting jumpers on the evm etc but still > couldnt retarget. > > Followed the advice of a couple of guys that were > nice enough > to respond. Still no dice. > > Using CW ver 3.5, IDE ver 4.06 > > Happy developing > Joe McCarron __________________________________

(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )

There is no FAQ for this forum that I am aware of, so please bear with me if this question is out of place. Is this the right forum to look for a consultant for a DSP56807 related project? Thanks Luis Villa

(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )

Luis, I have worked with a company called Lectronix in Lansing, Michigan, USA and found them to be an excellent resource for both hardware and software design. Check out their site. http://www.lectronix.biz/ Terry Litinas Project Engineer ITW Balance Engineering 1731 Thorncroft Troy, Mi. 48084 Ph: (248)643-2876 Fx: (248)643-2888 -----Original Message----- From: LuisST [mailto:] Sent: Tuesday, May 20, 2003 7:00 PM To: Subject: [motoroladsp] Is this also a forum for commercial requests? There is no FAQ for this forum that I am aware of, so please bear with me if this question is out of place. Is this the right forum to look for a consultant for a DSP56807 related project? Thanks Luis Villa _____________________________________ /groups.php3

(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )

Motorola provides a list of registered design and consultant companies. Please visit the following link: http://e-www.motorola.com/webapp/sps/site/dap.search.framework?DAP_NEXT_ SCREEN=SEARCH Leonard -----Original Message----- From: LuisST [mailto:] Sent: Tuesday, May 20, 2003 4:00 PM To: Subject: [motoroladsp] Is this also a forum for commercial requests? There is no FAQ for this forum that I am aware of, so please bear with me if this question is out of place. Is this the right forum to look for a consultant for a DSP56807 related project? Thanks Luis Villa _____________________________________ /groups.php3

(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )

Are you looking for a US based consulting firm. One company called FSI system (http://www.fsisys.com/)in Rochester, New York, has done a lot of 807 related projects for other parties. C.W. --- LuisST <> wrote: > There is no FAQ for this forum that I am aware of, > so please bear with me if > this question is out of place. > > Is this the right forum to look for a consultant for > a DSP56807 related > project? > > Thanks > > Luis Villa __________________________________

(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )