Sign in
Search motoroladsp
Subscribe to motoroladsp
motoroladsp by Keywords
56303 | 563xx | 5680 | 56805 | 5680x | 56F80 | 56F800DEMO | 56F805 | 56f807 | 56F830 | ADC | Bootloader | Codec | CodeWarrior | CW5 | CW6 | Debugger | DSP56303 | DSP56303EVM | DSP563xx | DSP5680 | DSP56800 | DSP56807 | DSP56858 | DSP56858EVM | DSP56F803 | DSP56F805 | DSP56F807 | DSP56F80x | DSP56F826 | DSP56F827 | DSP56F8xx | EVM | FFT | Flash_over_jtag | GPIO | Interrupt | Interrupts | JTAG | LCD | Linker | MCF5307 | Metrowerks | Modulus | MSCAN | PCMaster | PWM | Quad | Rif | RTOS | SDK | SPI
Discussion Groups
Discussion Groups | Freescale DSPs | DSP56F807 - DSPCOMMPARALLEL
Technical discussions about Freescale (Motorola) DSPs (including the DSP56000, DSP56300, DSP56600, 56800 DSPs).
DSP56F807 - DSPCOMMPARALLEL - Lionel Degoutte - Aug 27 7:41:00 2003
|
Hello, We have The evaluation board DSP56F807 EVM-1 with codewarrior 5.2. We have bought the command converter DSPCOMMPARALLEL. When I try to use it with the evaluation board, I have a message : "FLASH PROGRAMMING FAILED". On the evaluation board, I put a jumper on JG4 to disable U9. Is it normal ? If not, what can i do ? Thanks in advance for any suggestions. Lionel |
|
|
(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )
Re: DSP56F807 - DSPCOMMPARALLEL - Charlie W - Aug 27 15:59:00 2003
|
You are correct. All Motorola DSP56F80x/2x EVMs have on-board command converter. If you use stand alone JTAG command converter, you must put jumper on JG4. C.W. --- Lionel Degoutte <> wrote: > Hello, > > We have The evaluation board DSP56F807 EVM-1 with > codewarrior 5.2. We have > bought the command converter DSPCOMMPARALLEL. > When I try to use it with the evaluation board, I > have a message : "FLASH > PROGRAMMING FAILED". > On the evaluation board, I put a jumper on JG4 to > disable U9. > Is it normal ? If not, what can i do ? > > Thanks in advance for any suggestions. > > Lionel __________________________________ |
|
|
(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )
Re: DSP56F807 - DSPCOMMPARALLEL - isierra95 - Aug 27 19:18:00 2003
|
Lionel, When you are using the DSPCOMMPARALLEL you have to make sure that you have JG4 jumpered. If you don't have it jumpered then the only way that you could connect to the board would be through the parallel port connector on the board. -Irene --- In , Charlie W <charliewtx@y...> wrote: > You are correct. All Motorola DSP56F80x/2x EVMs have > on-board command converter. If you use stand alone > JTAG command converter, you must put jumper on JG4. > > C.W. > --- Lionel Degoutte <ldegoutte@r...> wrote: > > Hello, > > > > We have The evaluation board DSP56F807 EVM-1 with > > codewarrior 5.2. We have > > bought the command converter DSPCOMMPARALLEL. > > When I try to use it with the evaluation board, I > > have a message : "FLASH > > PROGRAMMING FAILED". > > On the evaluation board, I put a jumper on JG4 to > > disable U9. > > Is it normal ? If not, what can i do ? > > > > Thanks in advance for any suggestions. > > > > Lionel > > > > > > __________________________________ |
(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )