Sign in

username:

password:



Not a member?

Search motoroladsp



Search tips

Subscribe to motoroladsp



motoroladsp by Keywords

56303 | 563xx | 5680 | 56805 | 5680x | 56F80 | 56F800DEMO | 56F805 | 56f807 | 56F830 | ADC | Bootloader | Codec | CodeWarrior | CW5 | CW6 | Debugger | DSP56303 | DSP56303EVM | DSP563xx | DSP5680 | DSP56800 | DSP56807 | DSP56858 | DSP56858EVM | DSP56F803 | DSP56F805 | DSP56F807 | DSP56F80x | DSP56F826 | DSP56F827 | DSP56F8xx | EVM | FFT | Flash_over_jtag | GPIO | Interrupt | Interrupts | JTAG | LCD | Linker | MCF5307 | Metrowerks | Modulus | MSCAN | PCMaster | PWM | Quad | Rif | RTOS | SDK | SPI

Ads

Discussion Groups

See Also

Embedded SystemsFPGAElectronics

Discussion Groups | Freescale DSPs | GPIO- Timer programming

Technical discussions about Freescale (Motorola) DSPs (including the DSP56000, DSP56300, DSP56600, 56800 DSPs).

  

Post a new Thread

GPIO- Timer programming - ritu_eshar - Aug 20 17:53:00 2002

Hi all,

I am trying to program the following:
If I were to feed in a 1KHz square wave (voltage ranges between 0~3
volts) into Timer A0 channel as the input.

The output I should be able to see at say GPIO_B( pin 7),the same
frequency Square wave .

I have been using strict C without the SDK tools, as there occur
stringent timing requirements and hence am losing time (alloted to
opening of drivers etc) for my application.

Would greatly appreciate any feedback in this regard. Am a newbie to
DSP programming and C as well. Thanks for you time n patience.

Ritu.



______________________________
New Code Sharing Section now Live on DSPRelated.com. Learn about the Reward Program for Contributors here.



(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )

Re: GPIO- Timer programming - mwmann_at_motorola - Sep 3 18:07:00 2002

If you check the FAQs on Motorola's web site (at http://e-
www.motorola.com/cgi-bin/faq.cgi?kbase=dsp&prod_default=56800) and
search on the key words "simple peripheral drivers", you will see
some software examples of how to drive GPIO pins using one of the
quad timers. Non SDK and SDK compliant versions are provided.

--- In motoroladsp@y..., "ritu_eshar" <ritu_eshar@y...> wrote:
> Hi all,
>
> I am trying to program the following: >
> If I were to feed in a 1KHz square wave (voltage ranges between 0~3
> volts) into Timer A0 channel as the input.
>
> The output I should be able to see at say GPIO_B( pin 7),the same
> frequency Square wave .
>
> I have been using strict C without the SDK tools, as there occur
> stringent timing requirements and hence am losing time (alloted to
> opening of drivers etc) for my application.
>
> Would greatly appreciate any feedback in this regard. Am a newbie
to
> DSP programming and C as well. Thanks for you time n patience.
>
> Ritu.


______________________________
Start your Android Ice Cream Sandwich development on TI's AM35x Sitara ARM Cortex-A8 processor today.



(You need to be a member of motoroladsp -- send a blank email to motoroladsp-subscribe@yahoogroups.com )