56303 | 563xx | 5680 | 56805 | 5680x | 56F80 | 56F800DEMO | 56F805 | 56f807 | 56F830 | ADC | Bootloader | Codec | CodeWarrior | CW5 | CW6 | Debugger | DSP56303 | DSP56303EVM | DSP563xx | DSP5680 | DSP56800 | DSP56807 | DSP56858 | DSP56858EVM | DSP56F803 | DSP56F805 | DSP56F807 | DSP56F80x | DSP56F826 | DSP56F827 | DSP56F8xx | EVM | FFT | Flash_over_jtag | GPIO | Interrupt | Interrupts | JTAG | LCD | Linker | MCF5307 | Metrowerks | Modulus | MSCAN | PCMaster | PWM | Quad | Rif | RTOS | SDK | SPI

DSP56858EVM   [5 Articles]

Hello all of you, I'm new in using MOTOROLA DSPS, so i'd like to get a DSP56858EVM or 52EVM but I don't know who can sell me taht modules here in Mexico City, so, i...

DSP56858EVM Codec

OK. I have the codec running both at the independent and dependent level on a DSP56858EVM. I am really looking to strip this driver down to a two sample depth (one ...

DSP56858EVM bootloading

Hi, How do I go about programing the DSP56858EVM board so that I can run a program without using the metroworks debugger? i've managed to make a .s file but don't...

CCS: Cable disconneted, codewarrior and dsp56858evm   [2 Articles]

We have been trying to connect the dsp56858evm to the computer using codewarrioir via a parallel port cable. We are continuously receiving the following error: CCS: Cable ...

Info on Codewarrior USB Tap

Hello: I am looking for a connection to a Freescale 56858 that will work with Codewarrior’s debugger. Currently we are talking to the DSP56858EVM through its parallel port ...

IIR filter usage with DSP56858EVM   [3 Articles]

Hello, I am new to the group as well as to the Motorola DSP56858EVM. I am trying to implement a simple IIR filter, but it is not working properly (i.e. the cut...

ElectricalFeaturesEVM56858   [2 Articles]

Hi all, I´m develping an audio aplicattion using the DSP56858EVM, now I want to connect an amplifier at the line-in of the EVM to work with voice signals from a ...

Clock frequency   [2 Articles]

I guess the operating clock frequency for DSP56858EVM by default is 120MHz. If yes, Can it be increased more than 120Mhz? If no, how can it be operated at maximum f...

DSP56858EVM - Can't get SPI boot to work.   [4 Articles]

DSP56858EVM - Can't get SPI boot to work. Hello all, I am trying to execute the Second Stage SPI Bootloader Demo in the SDK using a DSP56858EVM boa...

DSP56858EVM, CW6.0 & SDK2.0E   [2 Articles]

Have just received my EVM, copy of CW6.0 (patched to 6.0.1) and SDK2.0E. Following th instructions in the targetting manual, I get to 1.2.4 Step 3 (execute a builda...

codec example in Embedded SDK for DSP56800E

hi I have installed the embedded sdk along with dSP56858EVM. I opened the codec.mcp project. I was able to build the project sucessfully but didn't find the de...

56858 second stage serial bootloader

Hello, I have been trying to get the second stage SPI serial bootloader to work on the DSP56858EVM using the example from Precessor Expert. After much hair pulling it looks a...

RE: NewMicros JTAG

Message I have been using the New Micros JTAG 14-Pin cable for about a month now without a problem.  I am using it with my DSP56858EVM.  The only thing that ...

RE: Codewarrior V7.2 56800 / E Can't debug.

Codewarrior V7.2 56800 / E Can't debug. Hi again,       Just in case any of you guys have similar problems, it turns out that the inbuilt para...

[DSP56858EVM] LCD ??

Does anyone know what type of LCD I can (should) use on the DSP56858EVM? Thanx --- Robert Wood <> wrote: > Having replaced the HVD230 with a 82C250 and do...

need an Efficient Codec Interface method for 56858EVM

Hello, I'm currently trying to get an algorithm to run in real-time, but I am running out of MIPs. Here are the specifics and I appreciate any suggestions offe...

Something to ponder

Actually just wondering, have the dsp56858evm board and actually wondering how to access the speaker and microphone inputs and outputs, just want to pass da...

Re: Codewarrior 6 - Steals the parallel port?   [3 Articles]

I have noticed that using the printer port with the DSP56858EVM does seem to "scramble" the port and/or driver so that itno longer recognizes my printer.  I use a switc...

56F8322 programming

Dear forum members, I'm new to DSP programming. I'm unable to program my DSP processor, and posting this message after extensive (i hope!) search in the internet. But, I coul...

RE: jtag command converter   [4 Articles]

Message I have been using the JTAG-Cable-14P from New Micros http://www.newmicros.com   for months now without a problem.  I've used it wit...

RE: MC56F8300DSK Problem   [3 Articles]

Message Hello, I am using DSP56858EVM and originally I also got the same error message.  I would keep trying and usually by the third or fourth t...