entry point _c_int00

Started by prajumokeri May 7, 2003

Hi,
I have just started with code composer & dsk5402.I am trying to
interface an FPGA kit with dsk5402 through rs232 interface.These are
the problems I,m facing
1.I can't include headerfiles such as "type.h","board.h","uart.h" etc
Whenever I am trying to include these files the message "cannot
include file "(filename.h)" " appears
2.Error "Undefined symbols" appears when using functions such as
'uart_write_reg()','uart_read_reg()' etc
3.Warning entry point"_c_int00" referenced but not defined appears

Can anyone help me solving these problems?

Thanking in advance..
Praju



Hi prajumokeri,

Have you set the path for the include files in Project->Options ?

Martin.

On Wednesday 07 May 2003 08:18, prajumokeri wrote:
> Hi,
> I have just started with code composer & dsk5402.I am trying to
> interface an FPGA kit with dsk5402 through rs232 interface.These are
> the problems I,m facing
> 1.I can't include headerfiles such as "type.h","board.h","uart.h" etc
> Whenever I am trying to include these files the message "cannot
> include file "(filename.h)" " appears
> 2.Error "Undefined symbols" appears when using functions such as
> 'uart_write_reg()','uart_read_reg()' etc
> 3.Warning entry point"_c_int00" referenced but not defined appears
>
> Can anyone help me solving these problems?
>
> Thanking in advance..
> Praju >
> _____________________________________
> Note: If you do a simple "reply" with your email client, only the author of
> this message will receive your answer. You need to do a "reply all" if you
> want your answer to be distributed to the entire group.
>
> _____________________________________
> About this discussion group:
>
> To Join: Send an email to
>
> To Post: Send an email to
>
> To Leave: Send an email to
>
> Archives: http://www.yahoogroups.com/group/c54x
>
> Other Groups: http://www.dsprelated.com > ">http://docs.yahoo.com/info/terms/






On Wed, 7 May 2003, prajumokeri wrote:

>
> Hi,
> I have just started with code composer & dsk5402.I am trying to
> interface an FPGA kit with dsk5402 through rs232 interface.These are
> the problems I,m facing
> 1.I can't include headerfiles such as "type.h","board.h","uart.h" etc
> Whenever I am trying to include these files the message "cannot
> include file "(filename.h)" " appears

You must specify where is the header files location. You can set this
using build option. If you install CCS in c:\ti then then the header files
are in C:\ti\c5400\dsk5402\include.

> 2.Error "Undefined symbols" appears when using functions such as
> 'uart_write_reg()','uart_read_reg()' etc

> 3.Warning entry point"_c_int00" referenced but not defined appears
>

I think your problem is: forgot to add the librariy in the project.
If you want to use DSK library (using functions to access DSK peripherals)
you must include C:\ti\c5400\dsk5402\lib\dsk5402.lib in your project.

The third problem is because you didn't include run time library
C:\ti\c5400\cgtools\lib\rts.lib in your project.

Cheers
> Can anyone help me solving these problems?
>
> Thanking in advance..
> Praju >
> _____________________________________
> Note: If you do a simple "reply" with your email client, only the author of
this message will receive your answer. You need to do a "reply all" if you want
your answer to be distributed to the entire group.
>
> _____________________________________
> About this discussion group:
>
> To Join: Send an email to
>
> To Post: Send an email to
>
> To Leave: Send an email to
>
> Archives: http://www.yahoogroups.com/group/c54x
>
> Other Groups: http://www.dsprelated.com > ">http://docs.yahoo.com/info/terms/




On Wed, 7 May 2003, prajumokeri wrote:

>
> Hi,
> I have just started with code composer & dsk5402.I am trying to
> interface an FPGA kit with dsk5402 through rs232 interface.These are
> the problems I,m facing
> 1.I can't include headerfiles such as "type.h","board.h","uart.h" etc
> Whenever I am trying to include these files the message "cannot
> include file "(filename.h)" " appears

You must specify where is the header files location. You can set this
using build option. If you install CCS in c:\ti then then the header files
are in C:\ti\c5400\dsk5402\include.

> 2.Error "Undefined symbols" appears when using functions such as
> 'uart_write_reg()','uart_read_reg()' etc

> 3.Warning entry point"_c_int00" referenced but not defined appears
>

I think your problem is: forgot to add the librariy in the project.
If you want to use DSK library (using functions to access DSK peripherals)
you must include C:\ti\c5400\dsk5402\lib\dsk5402.lib in your project.

The third problem is because you didn't include run time library
C:\ti\c5400\cgtools\lib\rts.lib in your project.

Cheers
> Can anyone help me solving these problems?
>
> Thanking in advance..
> Praju >
> _____________________________________
> Note: If you do a simple "reply" with your email client, only the author of
this message will receive your answer. You need to do a "reply all" if you want
your answer to be distributed to the entire group.
>
> _____________________________________
> About this discussion group:
>
> To Join: Send an email to
>
> To Post: Send an email to
>
> To Leave: Send an email to
>
> Archives: http://www.yahoogroups.com/group/c54x
>
> Other Groups: http://www.dsprelated.com > ">http://docs.yahoo.com/info/terms/


Hi prajumokeri,

Have you set the path for the include files in Project->Options ?

Martin.

On Wednesday 07 May 2003 08:18, prajumokeri wrote:
> Hi,
> I have just started with code composer & dsk5402.I am trying to
> interface an FPGA kit with dsk5402 through rs232 interface.These are
> the problems I,m facing
> 1.I can't include headerfiles such as "type.h","board.h","uart.h" etc
> Whenever I am trying to include these files the message "cannot
> include file "(filename.h)" " appears
> 2.Error "Undefined symbols" appears when using functions such as
> 'uart_write_reg()','uart_read_reg()' etc
> 3.Warning entry point"_c_int00" referenced but not defined appears
>
> Can anyone help me solving these problems?
>
> Thanking in advance..
> Praju >
> _____________________________________
> Note: If you do a simple "reply" with your email client, only the author of
> this message will receive your answer. You need to do a "reply all" if you
> want your answer to be distributed to the entire group.
>
> _____________________________________
> About this discussion group:
>
> To Join: Send an email to
>
> To Post: Send an email to
>
> To Leave: Send an email to
>
> Archives: http://www.yahoogroups.com/group/c54x
>
> Other Groups: http://www.dsprelated.com > ">http://docs.yahoo.com/info/terms/





Hi,
I have just started with code composer & dsk5402.I am trying to
interface an FPGA kit with dsk5402 through rs232 interface.These are
the problems I,m facing
1.I can't include headerfiles such as "type.h","board.h","uart.h" etc
Whenever I am trying to include these files the message "cannot
include file "(filename.h)" " appears
2.Error "Undefined symbols" appears when using functions such as
'uart_write_reg()','uart_read_reg()' etc
3.Warning entry point"_c_int00" referenced but not defined appears

Can anyone help me solving these problems?

Thanking in advance..
Praju