Armin,
1. Please send your requests to the c6x group, not to me directly. We
want to give others a chance to learn.
2. I suggest that you download [and use] the following documents from TI:
TMS320C6000 Imaging Developer’s Kit (IDK) Video Device Driver User’s
Guide - Literature Number: SPRU499 December 2000
TMS320C6000 Imaging Developer’s Kit (IDK) User’s Guide Literature
Number: SPRU494A September 2001
3. This product was released about 12-13 years ago. With CCS v3.3, you
probably do not complete C++ support - TI phased it in during this time,
but I am pretty sure that most C++ features - except templates - were
supported.
4. RE: "also i cant write main function in c++ language". When you have
a problem, it is customary to include a short example function that
demonstrates the problem and to include a specific description of the
problem, like the code below gets 'compiler error 911'.
mikedunn
On 8/16/2013 7:39 AM, Armin Nemati wrote:
> yes, i have a camera that it connect to the
daughtercard,
> i want to capture video and display that video on the other monitor, i
> use the vcard.lib and vcap.c and vdis.c and i attach the header file
> to project but the ccs cant recognize the functions.this is my
> problem,also i cant write main function in c++ language,do you have
> any information about that main functions?
>
>
> *From:* mikedunn
> *To:* Richard Williams
> *Cc:* Jeff Brower ; Armin Nemati
> ; c...
> *Sent:* Friday, August 16, 2013 9:16 AM
> *Subject:* Re: [c6x] Re: ccs6711 with imaging daughter card
>
> Armid & Richard,
>
> TI had a 'kit' that packaged the DSK and video card together [I
don't
> remember if the DSK was 6711 or 6416]. It was called the IDK [Imaging
> Development Kit] and it originally shipped with a fair amount of
> imaging software including at least one functional imaging
> application. I think that the IDK was a precursor [or early version]
> of the surveillance sw. If you have this sw, you may hold back on
> upgrading - the original sw is over 10 years old and you may have
> problems trying to use it with new tools. I am pretty sure that TI
> has the documentation - there were a few manuals specific to the IDK,
> but I doubt that they have the sw.
>
> mikedunn
>
> On 8/15/2013 3:48 PM, Richard Williams wrote:
>> Armid,
>>
>> Which imaging daughter card do you have?
>>
>> Are you saying that your project is to receive some video
>> then forward that video to some output
>> so it can be viewed on an external monitor?
>>
>> Do I have a correct understanding of your project?
>>
>> This may be a good place to start searching for info:
>>
>>
>> This may be a good place to get info on the 6711 DSP:
>>
>>
>> you will want to download/install the latest set of development and
>> debug tools
>> for the 6711.
>> (compiler, linker, assembler, debugger)
>>
>> Have you downloaded the document that describes your imaging daughter
>> card?
>>
>> also spru494.pdf
>> also spru495.pdf
>>
>> Have you downloaded the CSL library for the 6000 series of T.I. DSPs?
>>
>> Have you downloaded the CSL source code header files?
>>
>> Are you going to use the BIOS or code everything yourself?
>>
>> The above will seem like a LOT of reading/learning to do, but once
>> the basics
>> are learned, then the rest is relatively simple.
>>
>> I hope this helps to get you started.
>>
>> R. Williams
>>
>> ---------- Original Message -----------
>> From: "Jeff Brower"
>> >
>> To: "Armin Nemati"
>> >
>> Cc: c...
>> Sent: Thu, 15 Aug 2013 15:15:02 -0500 (CDT)
>> Subject: [c6x] Re: ccs6711 with imaging daughter card
>>
>> > Armin-
>> >
>> > Please post to the group.
>> >
>> > -Jeff
>> >
>> > > i am starter student
>> > > i want to drive dsk6711 with ccsv3.3
>> > > i have drivers
>> > > i have an imaging daughter card too
>> > > i want a project to run that daughter card and see the video that
>> the camera
>> had captured.
>> > > can you help me?please answer me
>> > >
>> > >
"'"'"""'""""""""""""""""""""""""""""""""""""""""""""""""'""""""
>> > >
>> > > Sincerity
>> > >
>> > > --------------------
>> > > Armin Nemati
>> > > MSC- Digital Electronic
>> > > Iran University of Science & Technology (IUST)
>> > > 13185.768, Tehran, Iran
>> > >
>> > > E:a...@elec.iust.ac.ir
>>
>> > > Skype: Armin Nemati
>> > >
>> > >
"'"'"""'""""""""""""""""""""""""""""""""""""""""""""""""'""""""
>> > >
>> > >
>> > >
>> > > ________________________________
>> > > From: Jeff Brower
>> >
>> > > To: Shiva >
>> > > Cc: c...
>> > > Sent: Wednesday, August 14, 2013 10:58 PM
>> > > Subject: Re: [c6x] ccs version 4
>> > >
>> > >
>> > > Shiva
>> > >
>> > >> I used to work with code composer studio V3.1, but now
>> > >> i want to start using ccs v4. I found it different from
>> > >> v3.1 and i could not run the program on it. i just
>> > >> could build the program. would you please help me about
>> > >> how to run a program on ccs v4?
>> > >
>> > > Would suggest that you use CCS5, as that is the current supported
>> version,
>> and fixes numerous bugs with v4. That is
>> > > your processor type? Also do you have an EVM or DSK board? If
>> so, what type?
>> > >
>> > > -Jeff
>> ------- End of Original Message -------
>>
>
