Multi-Decimation Stage Filtering for Sigma Delta ADCs: Design and Optimization
A Matlab toolbox streamlines the design and optimization of multi-stage decimation filters for sigma-delta ADCs. MSD-toolbox automates stage-count and decimation-factor selection, generates Parks-McClellan equiripple FIR coefficients, and iteratively selects coefficient quantization to meet in-band noise constraints. It accepts sigma-delta bitstream stimuli for spectral and intra-stage analysis, includes cost estimation routines, and is published open-source on MathWorks with examples and a dissertation reference.
Canonic Signed Digit (CSD) Representation of Integers
Canonic Signed Digit (CSD) encoding slashes the number of nonzero bits in integer coefficients, enabling multiplierless FIR filters implemented with shifts and adds. This post uses MATLAB code to demonstrate CSD rules, show how negative values work, and plot the distribution of signed digits as bit width changes. It finishes with practical techniques to minimize signed digits per coefficient for area and power efficient filter designs.
Matlab Code to Synthesize Multiplierless FIR Filters
Learn how to build multiplierless FIR lowpass filters in Matlab using Canonic Signed-Digit coefficients. The post explains converting Parks-McClellan floating-point taps to scaled integers, then to exact CSD digits, and includes two m-files that search maintap scaling to minimize signed digits while preserving the filter response. Practical notes cover external gain compensation, the 2/3 full-scale CSD limit, and sensitivity to pass/stop edges.
Digital PLL's -- Part 2
Neil Robertson builds a Z-domain model of a second-order digital PLL with a proportional-plus-integral loop filter, then derives closed-form formulas for KL and KI from the desired loop natural frequency and damping. The post explains the s → (z - 1)/Ts approximation, shows how to form the closed-loop IIR CL(z) for step and frequency responses, and highlights when the linear Z-domain model falls short of nonlinear acquisition behavior.
Digital PLL's -- Part 1
A hands-on introduction to time-domain digital phase-locked loops, Neil Robertson builds a simple DPLL model in MATLAB and walks through the NCO, phase detector, and PI loop filter implementations. The post uses phase-in-cycles arithmetic to show how the phase accumulator, detector wrapping, and loop filter interact, and it contrasts linear steady-state behavior with the nonlinear acquisition seen when initial frequency error is large. Part 2 will cover frequency-domain tuning of the loop gains.
A poor man's Simulink
Markus Nentwig built a compact glue layer that embeds NGSPICE into Octave to cosimulate continuous-time circuits and digital control. The article walks through an RC lowpass example, the MEX-based Octave interface, and the breakpoint-driven cosimulation flow, showing how adaptive SPICE integration handles asynchronous and time-triggered events. It presents a practical, low-cost alternative to Simulink for tightly coupled analog-digital system design.
Spline interpolation
Markus Nentwig provides a cookbook for segmented cubic spline interpolation that turns scattered or noisy data into efficient fixed-point functions. The article shows how to build third-order polynomial segments with explicit value and slope control via basis functions, solve scaling factors by least-squares in Octave/Matlab, and export coefficients for Verilog RTL evaluation using the Horner scheme and practical fixed-point tips.
'z' as in 'Zorro': Frequency Masking FIR
Markus Nentwig shows an efficient way to build steep wideband FIR filters by combining upsampled and complementary stages, then masking their spectra. He provides a Matlab and Octave design program that uses a generic least-squares optimizer to place coefficients, letting you explore filter sizes and oversampling while cutting computational cost significantly compared to a conventional symmetric FIR.
FIR sideways (interpolator polyphase decomposition)
Markus Nentwig presents a compact way to implement a symmetric FIR interpolator by rethinking the usual tapped delay line. The 1:3 polyphase example uses separate delay lines per coefficient to skip multiplies on known zeros and exploit symmetry, cutting multiplications substantially; a Matlab/Octave demo and notes on ASIC-friendly implementation are included to help evaluate real-world cost tradeoffs.
Design of an anti-aliasing filter for a DAC
If you need a practical way to design an anti-aliasing filter for a DAC, this post delivers an Octave/Matlab script that numerically optimizes a Laplace-domain transfer function for linear phase and arbitrary magnitude. The routine models the DAC sample-and-hold sinc response, compensates group delay automatically, and can include an optional multiplierless FIR equalizer. An example shows a 5.4 dB objective improvement and reduced analog Q for easier implementation.
Setting Carrier to Noise Ratio in Simulations
Setting the right Gaussian noise level is easy once you know the math. This post derives simple, practical equations to compute noise density and the rms noise amplitude needed to achieve a target carrier to noise ratio at a receiver output. It shows how to get the noise-equivalent bandwidth from a discrete-time filter, how to compute N0 and sigma, and includes a MATLAB set_cnr function to generate the noise vector.
Radio Frequency Distortion Part II: A power spectrum model
Markus Nentwig presents a power-spectrum model that predicts RF nonlinear distortion from spectral power values instead of time-domain signals. The model computes distortion as repeated convolutions with a frequency-reversed replica and uses an FFT/IFFT trick with real-valued arithmetic for very high efficiency, making it suitable for system-level simulations and interference-aware radios. It is accurate for OFDM-like, Gaussian-amplitude signals when spectral binning is sufficiently fine; narrowband cases require denser bins.
Fitting Filters to Measured Amplitude Response Data Using invfreqz in Matlab
This post is a redirect notice for a code snippet now hosted elsewhere. If you were looking for the invfreqz example on fitting a filter to measured amplitude response data, this page simply points you to the new location and asks you to update your bookmark.
Design IIR Band-Reject Filters
This post walks through designing IIR Butterworth band-reject filters and provides two MATLAB synthesis functions, br_synth1.m and br_synth2.m. br_synth1 accepts a null frequency plus an upper -3 dB frequency, while br_synth2 takes lower and upper -3 dB frequencies. The author demonstrates an example where a 2nd-order prototype yields a 4th-order H(z), prints b and a coefficients, and plots the response using freqz.
Feedback Controllers - Making Hardware with Firmware. Part 9. Closing the low-latency loop
This article demonstrates combining DSP and feedback-control on an Intel Cyclone floating-point FPGA to build low-latency closed-loop circuit emulators and controllers. Using a single floating-point biquad at 1.6 Msps, an IFFT multi-tone 4.096 ms capture for wideband measurement, and MATLAB references for verification, the author achieves sub-nanosecond timing insight and applies DSP phase compensation to cancel about 100 pF of PCB parasitics.
ADC Clock Jitter Model, Part 2 – Random Jitter
Neil Robertson shows how to simulate ADC sample-clock random jitter in Matlab, moving from band-limited Gaussian noise to wideband and close-in phase noise. The post highlights practical artifacts such as aliasing of wideband clock noise, the 20*log10 dependence of jitter sidebands on input frequency, and why cubic interpolation plus a custom noise_filter produces accurate rms and spectral results engineers can trust.
Update to a Narrow Bandpass Filter in Octave or Matlab
Paul Lovell presents an updated, compact Octave/Matlab implementation of a narrow bandpass FIR that runs about four times faster and uses float32 to cut processing cost. The design combines a single matrix IFIR stage with three moving-sum (RRS) stages per baseband, auto-calculates the IFIR expansion factor, and adds easier parameter setup plus WAV I/O and FFT plots. A TensorFlow Colab demo is also provided.
The Phase Vocoder Transform
Treating the phase vocoder as a continuous transform, this post frames PV(x,α,β) as a bijection on signal space and derives the domain constraints needed for an inverse mapping. It uses geometric intuition and group-theory analogies to explain negative and zero scalings, then brings the idea back to DSP to show how aliasing and phase artifacts appear. The Laroche and Dolson consistency measure D_M plus MATLAB experiments are used to compare classic and identity phase-locking reconstructions.
An Efficient Lowpass Filter in Octave
Paul Lovell presents an efficient linear-phase lowpass FIR implemented in Octave, built as a Matrix IFIR with two matrix band-edge shaping stages followed by three recursive running-sum stages. The design reshapes input blocks into matrices to exploit interpolation structure and uses cumsum-based moving sums for speed. For a 200 Hz cutoff at 48 kHz the five-stage example ran about 15 times faster than a single-stage FIR.
Canonic Signed Digit (CSD) Representation of Integers
Canonic Signed Digit (CSD) encoding slashes the number of nonzero bits in integer coefficients, enabling multiplierless FIR filters implemented with shifts and adds. This post uses MATLAB code to demonstrate CSD rules, show how negative values work, and plot the distribution of signed digits as bit width changes. It finishes with practical techniques to minimize signed digits per coefficient for area and power efficient filter designs.
Bank-switched Farrow resampler
Markus Nentwig proposes a bank-switched variant of the Farrow resampler that breaks each impulse-response segment into multiple sub-segments, enabling accurate interpolation with lower-order polynomials and fewer multiplications per output. This trades increased total coefficient storage for computational savings. The post explains the concept, connects it to polyphase FIR interpolation, and provides Matlab/Octave and C example code for practical evaluation.
Interpolator Design: Get the Stopbands Right
In this article, I present a simple approach for designing interpolators that takes the guesswork out of determining the stopbands.
Simulink-Simulation of SSB demodulation
This post walks through Simulink models that implement SSB demodulation and modulation, using Richard Lyons' phasing method as a foundation. It shows practical models for simple carrier multiplication and for the phasing method with cosine and -sin paths plus Hilbert filtering, and it highlights sampling, decimation, filter choices, and delay alignment to make the techniques work in simulation.
Python number crunching faster? Part I
Christopher Felton walks through simple benchmarks comparing raw Python, numpy, and PyPy for numeric workloads, and shares what surprised him about performance. He shows that idiomatic Python optimizations such as list comprehensions and built-ins plus the PyPy JIT can sometimes beat a numpy approach for small tests, and explains why native PyPy numpy progress matters for scientific users.
Setting Carrier to Noise Ratio in Simulations
Setting the right Gaussian noise level is easy once you know the math. This post derives simple, practical equations to compute noise density and the rms noise amplitude needed to achieve a target carrier to noise ratio at a receiver output. It shows how to get the noise-equivalent bandwidth from a discrete-time filter, how to compute N0 and sigma, and includes a MATLAB set_cnr function to generate the noise vector.
Least-squares magic bullets? The Moore-Penrose Pseudoinverse
Markus Nentwig walks through a practical way to remove power-line hum from measurements using the Moore-Penrose pseudoinverse. He builds a harmonic basis, computes pinv(basis) to get least-squares coefficients, and reconstructs and subtracts the hum, with a ready-to-run Matlab example. The post highlights limits and performance: basis-like signal components will be removed, and accuracy improves with the square root of sample count.
Modelling a Noisy Communication Signal in MATLAB for the Analog to Digital Conversion Process
Practical signal modeling treats receiver noise as a fixed power source, not something tied to the transmitted waveform. Parth demonstrates why using MATLAB's awgn(sig,SNR,'measured') can misrepresent an analog front end and provides a short function that scales your signal so the added AWGN produces the desired receiver noise variance. This prepares realistic inputs for upcoming ADC simulations.
Generating Partially Correlated Random Variables
Designing signals to match a target covariance is simpler than it sounds. This post shows how to build partially correlated complex signals by hand for the two-signal case, then generalizes to N signals using the Cholesky decomposition. Short MATLAB examples demonstrate the two-line implementation and the article highlights numerical caveats when a covariance is only positive semidefinite.
Multi-Decimation Stage Filtering for Sigma Delta ADCs: Design and Optimization
A Matlab toolbox streamlines the design and optimization of multi-stage decimation filters for sigma-delta ADCs. MSD-toolbox automates stage-count and decimation-factor selection, generates Parks-McClellan equiripple FIR coefficients, and iteratively selects coefficient quantization to meet in-band noise constraints. It accepts sigma-delta bitstream stimuli for spectral and intra-stage analysis, includes cost estimation routines, and is published open-source on MathWorks with examples and a dissertation reference.
Radio Frequency Distortion Part II: A power spectrum model
Markus Nentwig presents a power-spectrum model that predicts RF nonlinear distortion from spectral power values instead of time-domain signals. The model computes distortion as repeated convolutions with a frequency-reversed replica and uses an FFT/IFFT trick with real-valued arithmetic for very high efficiency, making it suitable for system-level simulations and interference-aware radios. It is accurate for OFDM-like, Gaussian-amplitude signals when spectral binning is sufficiently fine; narrowband cases require denser bins.
