DSPRelated.com

TMS320VC5509

Started by kumarabhi123 in TMS320c55x19 years ago 1 reply

THANK'S FOR THE HEPL ON THE UART.. I am new to TMS320VC5509 progamming. Can any one tell me 1. What are...

THANK'S FOR THE HEPL ON THE UART.. I am new to TMS320VC5509 progamming. Can any one tell me 1. What are the basic requirements for proting a code into the processor(S/w and Hardware). 2. Where should i start from , i mea


Interrupts on TMS320VC5509 EVM

Started by gms_reddy in TMS320c55x21 years ago

Hello, I am working with G.729AB now. I am trying to implement G.729AB with MCBSP interrupts on TMS320VC5509 EVM board (spectrum...

Hello, I am working with G.729AB now. I am trying to implement G.729AB with MCBSP interrupts on TMS320VC5509 EVM board (spectrum digital). When I try to implement with interrupts, the CCS (ver. 2.1) hangs and displays a message like this: Trouble Halting Target CPU: Proce


migrating from tms320vc5507 to tms320vc5509

Started by psyfusioncuki_13 in TMS320c55x16 years ago

Hello! I would like to get help about changing a processor in a design. My task would be to redesign a product with another dsp. The current...

Hello! I would like to get help about changing a processor in a design. My task would be to redesign a product with another dsp. The current setup uses a TMS320VC5507PGE processor, my question is that what technical modifications should be made if i have to change it to a TMS320VC5509PGE? I'm concerned about pin assignment, voltage levels and interface differences. Also I would like to know i...


the available frequency for c55 DSKs

Started by ahma...@yahoo.com in TMS320c55x16 years ago

Hi, Do you know the maximum available frequency for following bords: 1- DSK for tms320vc5510A 2- DSK for tms320vc5509 3- EVM for...

Hi, Do you know the maximum available frequency for following bords: 1- DSK for tms320vc5510A 2- DSK for tms320vc5509 3- EVM for tms320vc5502 for example for tms320c554cst the board frequency is 14.78*8=118MHz while the DSP can work on 120MHz. I mean the 118MHz in above boards. Regards


Ethernet interface with 5509

Started by kumarabhi123 in TMS320c55x19 years ago

Hello friends ... I want to interface the wiznet W3100A with the TMS320VC5509 controller. Is it possible to do so.I was...

Hello friends ... I want to interface the wiznet W3100A with the TMS320VC5509 controller. Is it possible to do so.I was going through W3100A data sheet there it was written [ The chip offers Intel and Motorola MCU (8051, i386, 6811 tested) bus interface,] , do


USB Connect/Disconnect

Started by sylvio_nanoptix in TMS320c55x19 years ago 1 reply

Hi Everyone, Yet another USB dilemna with the TMS320VC5509. I am currently using the USB Driver from DDK 1.1 and I am...

Hi Everyone, Yet another USB dilemna with the TMS320VC5509. I am currently using the USB Driver from DDK 1.1 and I am having problems getting the USB device to reconnected if I unplug and replug the USB cable. Basically, if I unplug the USB cable I can't


Trouble using interrupts on TMS320VC5509 EVM

Started by lars...@gmail.com in TMS320c55x18 years ago

Hi! I'm using timer 0 interrupt to sample data from an external ADC via McBSP1. The problem is that the interrupt routine only runs a...

Hi! I'm using timer 0 interrupt to sample data from an external ADC via McBSP1. The problem is that the interrupt routine only runs a limited number of times and then the program goes out of line. The CCS displays the error message: "Processor communication timeout". I'm also experiencing that variables in the .bss section are being overwritten by some unk


Re: Re: TMS320VC5509A EMIF problem (due to PLL unstability I guess)???

Started by dpn...@dsp-bg.info in TMS320c55x18 years ago

Hi Michael, Thank you for this information. I think that there is a problem in the PLL design of C5509A. It is good that I manage to get...

Hi Michael, Thank you for this information. I think that there is a problem in the PLL design of C5509A. It is good that I manage to get 186MHz stable operation as I described. Regards Mitko ----- Original Message ----- From: "Michael Schuster" To: ; Sent: Monday, June 26, 2006 5:05 PM Subject: Re: [c55x] Re: TMS320VC5509


Hardware Extensions on C5509

Started by Maneesh Gupta in TMS320c55x22 years ago

Hi, My name is Maneesh Gupta and I am currently working on development of an application on TMS320CC55x. This application...

Hi, My name is Maneesh Gupta and I am currently working on development of an application on TMS320CC55x. This application makes use of C5509/C5510 Hardware Extensions. I am testing this code on TMS320VC5509 Revision D Board. The hardware accelerator code for "


TMS320VC5509 DSK, USB Data Transfer Inconsistency

Started by mgor...@yahoo.com in TMS320c55x17 years ago 1 reply

Hello, I am a grad student working on a DSP project for research and I haven't had much experience with DSP's and as such have run into a bit of...

Hello, I am a grad student working on a DSP project for research and I haven't had much experience with DSP's and as such have run into a bit of a stumbling block. I am currently using the TMS320VC5509A evaluation board from Spectrum Digital and I am attempting to get USB communication running between the board and the pc. I have downloaded the sample USB code from Spectrum Digital listed below, ...


TMS320vc5509 MMC/SD File layer suggestion

Started by peejayblack in TMS320c55x20 years ago 3 replies

Anyone The 5509 supports MMC/SD. Has anyone implimented this? Any suggestions on a file system layer. I want to be able ...

Anyone The 5509 supports MMC/SD. Has anyone implimented this? Any suggestions on a file system layer. I want to be able to read the card from a COT's card reader on my PC. 5509 MMC/SD File layer suggestion Phil Black