I have just switched from using the standard USB interface to EZLite Kit (Blackfin) to using JTAG (summit ice). And now I am...

I have just switched from using the standard USB interface to EZLite Kit (Blackfin) to using JTAG (summit ice). And now I am experiencing problems when I try to write to external memory. I have tried to access external memory by following trials: o Loading parts of the program

We're searching for a low cost JTAG emulator. Anybody an idea where we can find it? Thanks -- IMail Server for Windows NT....

We're searching for a low cost JTAG emulator. Anybody an idea where we can find it? Thanks -- IMail Server for Windows NT. Evaluation version. Copyright (c) 1995-98 Ipswitch, Inc. http://www.ipswitch.com/

Hi, Anyone has an example on using of jtag for data communication ? Thanks

Hi, Anyone has an example on using of jtag for data communication ? Thanks

hi, I was trying the Demo program PRIMEX on my ADSP 21160M EZ Lite Board. When using Parallel Port to download, everything...

hi, I was trying the Demo program PRIMEX on my ADSP 21160M EZ Lite Board. When using Parallel Port to download, everything works fine. But when I switch to JTAG emulator ICE, it seems the program is downloaded. But when I ran the program, the LED didn't light up.

hi friends, iam using ADSP 2191 ICE. Iam facing some problems while using ADSP2191 Emulator. 1)if i open ADSP 2191 in emulator...

hi friends, iam using ADSP 2191 ICE. Iam facing some problems while using ADSP2191 Emulator. 1)if i open ADSP 2191 in emulator mode,after connecting JTAG to target board it shows the error 0x8000 4005 from this mode of selection,i can't enter into emulatormode. for entering into emulator mode,first i should enter into simulato

Hi, I have a custom board with BF534 processor and spansion flash. When try to load the flash driver onto the board. I get the following...

Hi, I have a custom board with BF534 processor and spansion flash. When try to load the flash driver onto the board. I get the following error. "JTAG scan failed- check target power and emulator connection. Cannot load memory when target is running. error loading section "L1_code" to target." sometimes I get the following error as well. " Unable to halt processor, JTAG communication failed...

Hi! we have a Custom BF532 Board, which is working properly.......Newly we have soldered a new board of same PCB , the Board is not detected by...

Hi! we have a Custom BF532 Board, which is working properly.......Newly we have soldered a new board of same PCB , the Board is not detected by ICE.... ICE test is failing at step 4 "Determining Scan Path Length" Telling No devices Detected in the chain...... I don't have much Idea abt JTAG.....I didn't understand How to debug it...This PCB is already working properly....... Generally wh...

hi friends, how to transfer the data from system hard disk to ADSP-BF533 processor's SDRAM using JTAG emulator? regards, ...

hi friends, how to transfer the data from system hard disk to ADSP-BF533 processor's SDRAM using JTAG emulator? regards, meiyazhagan

Hi. In the ADSP-21262 datasheet (Rev B) is it stated that the TCK line (used for JTAG port) "must be asserted (pulsed low) after power-up or...

Hi. In the ADSP-21262 datasheet (Rev B) is it stated that the TCK line (used for JTAG port) "must be asserted (pulsed low) after power-up or held low for proper operation of the ADSP-21262". However, in the ADSP-21262 EZ-KIT LITE schematic diagram it is pulled- up to mantain a high when you just run the DSP without JTAG intervention. Of course the TRST* must be held down after power-up bu...

I wrote a small code in adsp2191 and that code is building properly in simulator. If i use emulator to connect to the target through JTAG...

I wrote a small code in adsp2191 and that code is building properly in simulator. If i use emulator to connect to the target through JTAG CONNECTOR,the code build message will comes and immediatly in the output window i am receiving the following ERROR  message,            

XL101-ICE Universal Serial Bus Emulator for Analog Devices JTAG DSPs The XL101-ICE system is a Universal Serial Bus(USB)- based...

XL101-ICE Universal Serial Bus Emulator for Analog Devices JTAG DSPs The XL101-ICE system is a Universal Serial Bus(USB)- based DSP emulator. This emulator provides a portable solutiondesigned to support Analog Devices (ADI) JTAG DSPs. The XL101- ICE emulator provides a simple, effic

contact me!

contact me!

I have extra JTAG emulators for sale. Please email me at s...@yahoo.com for more information. Sachin

I have extra JTAG emulators for sale. Please email me at s...@yahoo.com for more information. Sachin

Hi we are using adsp21364 for our audio processing application Is there any USB EZ extender which can be connected through ...

Hi we are using adsp21364 for our audio processing application Is there any USB EZ extender which can be connected through JTAG interface Regards saju s

some time when my jtag connector can't communicate with my target board ,often this led is in red. ...

some time when my jtag connector can't communicate with my target board ,often this led is in red.

Hi, --- saravana karthikeyan <> wrote: > > Dear andres > I am using ADSP-BF532 in my project. > > I have JTAG-Emulator...

Hi, --- saravana karthikeyan <> wrote: > > Dear andres > I am using ADSP-BF532 in my project. > > I have JTAG-Emulator and visual DSP++ > 3.1version. Good setup! > Flash-AM 29LV004BT.what is the proce

Got to make a decision on what type of EPROM to use on the board. I was going to follow the EZLITE kit and use the AM29LV081B but that means it...

Got to make a decision on what type of EPROM to use on the board. I was going to follow the EZLITE kit and use the AM29LV081B but that means it must be either programmed before being soldered to the board, or I need a JTAG programmer. The latter is a possibility, but what of the conventional alternative of a socket and a big DIL package? Would there be any problems with the extra track lengt...

Hello, Saravana Mmhhh.... seems lik you have custom board, don't you? Well. Do you have JTAG emulator and VisualDSP++? If so,...

Hello, Saravana Mmhhh.... seems lik you have custom board, don't you? Well. Do you have JTAG emulator and VisualDSP++? If so, you can load your data into the DSP internal memory for testing purposes, and then create a bootloader (a program which reads the data to be

Hi,I newly made a board using ADSP-21262. The Pcb has four layers including power plane and ground plane. The HPPCI emnlator can find out there is...

Hi,I newly made a board using ADSP-21262. The Pcb has four layers including power plane and ground plane. The HPPCI emnlator can find out there is 1 device in the JTAG chain. However, it fails to go into VDSP due to

(i'll be working with Blackfin) pretty damn expensive stuff. last year i did a project with TI DSP and the software and...

(i'll be working with Blackfin) pretty damn expensive stuff. last year i did a project with TI DSP and the software and hardware didn't come to as much as either of these alone. so i'm wondering if there are any other emulators (really JTAG programmers) that work with VDSP++..