i met the same problem in flash programing tms320F28335 using \"TMS320F28335 Flash API V1.01\" in CCS 3.354.1 with example along with the api...

i met the same problem in flash programing tms320F28335 using \"TMS320F28335 Flash API V1.01\" in CCS 3.354.1 with example along with the api release. following are codes slice from the example file: \" .............. /*------------------------------------------------------------------ Check the version of the API Flash_APIVersion() returns the version in floating point. Fla...

Hi All,, I am running my application at 128Mhz system clock out rate on Flash. Is it SCI module support for 5 Mbps baudrate for communicating...

Hi All,, I am running my application at 128Mhz system clock out rate on Flash. Is it SCI module support for 5 Mbps baudrate for communicating another SCI module in F2812.? One more thing is can i have the maximum baudrate of SCI module supports, Thanks in advance Regarsd, Srinu!!! OMAP35x EVM jump-starts low-power apps The modular and extensible OMAP35x Evaluation Module (EVM...

Hi, I have defined few constants like #define conversion 0.534 #define x 25 #define format 666.66667 If i run my program and see the...

Hi, I have defined few constants like #define conversion 0.534 #define x 25 #define format 666.66667 If i run my program and see the values of the variables it was wrong, hence it gave _IQ(conversion) in watch window to view the value, it shows that 'identifier not found : conversion' in the value column of watch window. Why it is? Then how can i ensure that, it has taken defined valu...

Hi all, When i run my program in RAM or Flash memory, it branches to illegal ISR routine. compilation and build is ok. No errors appeared. but...

Hi all, When i run my program in RAM or Flash memory, it branches to illegal ISR routine. compilation and build is ok. No errors appeared. but if i run my program again, it shows the status as running,but no output. what is the reason for it? Has anyone faced this thing before? Please help Thanks OMAP35x EVM jump-starts low-power apps The modular and extensible OMAP35x Evaluation ...

I'm trying to use SCI port on TMS320F2812 as UART with FIFO enabled. The idea of having FIFO is to reduce the interrupt burden for every...

I'm trying to use SCI port on TMS320F2812 as UART with FIFO enabled. The idea of having FIFO is to reduce the interrupt burden for every character. If received characters are less than FIFO size and receive line is idle for a long time then those characters are stuck in FIFO. Processor won't get interrupt for those characters until FIFO gets full. > From my experience with different UART

Hi all, May I know which capture units corresponds to which PWMs of EVA and EVB? I know that EVA has 3 capture units, CAP1, 2 and 3. Similarly...

Hi all, May I know which capture units corresponds to which PWMs of EVA and EVB? I know that EVA has 3 capture units, CAP1, 2 and 3. Similarly for EVB CAP4, 5 and 6 and time base can be chosen based on the values in CAPCONA/B registers. Incase, if I would like to use CAP1 for capturing the rising edge of CMPR1 and CAP2 for capturing the rising edge of CMPR3, How do I ensure that? Can any one ...

Hi, I am connecting F2812 and wish to run my program in flash memory. I have included F2812.cmd file, i have also included memcopy.c,...

Hi, I am connecting F2812 and wish to run my program in flash memory. I have included F2812.cmd file, i have also included memcopy.c, CSMpasswords.asm files. I have connected JP7 jumper to 1-2 position for booting from Flash. i have initialised the following. extern Uint16 RamfuncsLoadStart; extern Uint16 RamfuncsLoadEnd; extern Uint16 RamfuncsRunStart; MemCopy(&RamfuncsLoadStart, &R...

Hi, I Have the F2812eZdsp and XDS510USB. i am trying to connect eZdsp (spectrum digital)via XDS510USB, the error message was found is ""your...

Hi, I Have the F2812eZdsp and XDS510USB. i am trying to connect eZdsp (spectrum digital)via XDS510USB, the error message was found is ""your ccs does not support the target cruel orchid: you are using ccs3.1 or 3.3? kajan DSP: Device driver name:"C:\CCstudio_V3.1\drivers\sdgo28Xusb.dvr" Could you help me anybody to connect to the eZdsp?? regards, Kajan. OMAP35x EVM jump-starts ...

hi all. i am facing a problem regarding to the tms320f2812 dsp chip.when i give a power supply 12V, the current increase to 1A and the dsp...

hi all. i am facing a problem regarding to the tms320f2812 dsp chip.when i give a power supply 12V, the current increase to 1A and the dsp chip become hot. and how to solve it?will it affected to the board? before this, the current is 0.6A but when i try to power up the board yesterday, the current increase to 1A and the dsp chip become hot. i have no idea why it become like that. i have dis...

Hello all I am trying to use hyper terminal to flash code into F2810 chip. We are trying to develop own interface for serial flash. I use the...

Hello all I am trying to use hyper terminal to flash code into F2810 chip. We are trying to develop own interface for serial flash. I use the pdf from TI website as reference http://focus.ti.com/lit/an/spraaq2/spraaq2.pdf I was able to lock the baud rate and when I send the kernel (CKFA.bin) file , I get checksum error and also it says Flash already erased.I even changed the checksum in the ...