Forums More c3x
Capability of VC33
inhi! i'm new with VC33... i want to know, can it be use for LPF(low pass filter), Hilbert Transform? thanks, regards, Christian
hi! i'm new with VC33... i want to know, can it be use for LPF(low pass filter), Hilbert Transform? thanks, regards, Christian
what happens when VC33 is in MCBL and there is no BL program
Hi, I am using TMS320VC33 in MCBL mode.But till now we haven't done any boot loader programs, as we are in the initial stages of programming.We...
Hi, I am using TMS320VC33 in MCBL mode.But till now we haven't done any boot loader programs, as we are in the initial stages of programming.We are simply writing some code for adc, dac etc for testing purposes.Initially it was fine. But nowadays we find some kind of degradation in the performance of DSP in the sense that,after we run the program twice or thrice the dsp stops responding.hard...
erratic behaviour-code composer
inHi, I am new to this platform. I am using the tms320vc33. I am using code composer version.4.10.36 I have written an inialization code in...
Hi, I am new to this platform. I am using the tms320vc33. I am using code composer version.4.10.36 I have written an inialization code in (C and asm) for dsp. When I startup, the cpu registers are showing some default values and not zero. If I start to trace with these values, at the end of some function calls the trace goes to some unspecified location. But if I make the cpu regist...
How to declare 8-bit or 16-bit data in C31.?
inHi, I am using C31 processor , if i decalare "unsigned char" data or "unsigned short" , the code composer shows 32-bit assigned to it . Is it...
Hi, I am using C31 processor , if i decalare "unsigned char" data or "unsigned short" , the code composer shows 32-bit assigned to it . Is it possible to decalare 8-bit or 16-bit data type for the C31.? Also if two memories one 8-bit wide and another 16-bit are externallay attached to the C31, and if i want to move 8-bit memory data into 16-bit memory data what would be the efficient way to...
Defining array in memory other than .bss
inHi, i want to memory map an array variable in a external memory at specicific location. My memory DPR is maped at address 0x5000000 and...
Hi, i want to memory map an array variable in a external memory at specicific location. My memory DPR is maped at address 0x5000000 and i want to declare an array at address 0x5000033 suppose unsigned int myarray[100]; How can i memory map it at address 0x5000033.? Regards. N a j a m
Problems stepping in CC and vector definitions
inI've been given this new board to bring up. I see two problems (maybe they're related). The board features external RAM mapped from address...
I've been given this new board to bring up. I see two problems (maybe they're related). The board features external RAM mapped from address 0. The DSP is configured to run in Microprocessor mode for now during debugging and just load directly to RAM from the XDS510USB JTAG emulator. The connection to the board seems to be fine and I can manipulate values in RAM. 1. I cannot step....
cyrstal frequency and H1/H3 frequency
inhello friends here,I want to know what error with my new broad.:20MHz crystal feed to Xin and Xout pins,but the H1/H3 is a sine wave of 100MHz(I...
hello friends here,I want to know what error with my new broad.:20MHz crystal feed to Xin and Xout pins,but the H1/H3 is a sine wave of 100MHz(I thought it should be 50MHz) with a DC offset,H1=1.2sin(2*3.14*100MHz*t),please tell me why,thanks.
Instruction Set Simulator?
inHi, I was wondering if anyone knew of an instruction set simulator for the VC33? I can only find ISSs for the c5x and c6x...
Hi, I was wondering if anyone knew of an instruction set simulator for the VC33? I can only find ISSs for the c5x and c6x DSPs. Thanks, Jenny
Data Page Pointer (DP Register), TMS320VC33 DSP
inHello everyone, I am currently trying to debug a TMS320VC33 DSP target (my own design) board with the help of the XDS510PP (Plus) emulator and...
Hello everyone, I am currently trying to debug a TMS320VC33 DSP target (my own design) board with the help of the XDS510PP (Plus) emulator and Code Composer (version 4.10.36). I have downloaded the relevant drivers from the Spectrum Digital website and have established communications between the XDS510PP emulator and the target board, i.e. I can load and step through code as expected. My pro...
some basic doubts about the vc33 dsk
inhi, i'm a newbie with tms320vc33 dsk , and i would like to know : 1) is it possible for me to alternate between assembly language and C...
hi, i'm a newbie with tms320vc33 dsk , and i would like to know : 1) is it possible for me to alternate between assembly language and C language within a same source code. if yes, how? 2) the software included ( im using version 2.02) has up to 20 application files (dsk3a, dsk3d, dsk3win, dsk3osc, to name a few). so far, i'm only using DSK3DW, which is stated as the debugger. what are the ot...
Ask a Question to the DSPRelated community
To significantly increase your chances of receiving answers, please make sure to:
- Use a meaningful title
- Express your question clearly and well
- Do not use this forum to promote your product, service or business
- Write in clear, grammatical, correctly-spelled language
- Do not post content that violates a copyright