DSPRelated.com

hex2asm.exe

Started by miww...@aol.com in TMS320c3x19 years ago 1 reply

hi there, is there anyone who can help me out with a copy of hex2asm.exe. It looks, like TI had stopped ftp-support for c3x-files. ...

hi there, is there anyone who can help me out with a copy of hex2asm.exe. It looks, like TI had stopped ftp-support for c3x-files. Thanks in advance, Michael


FIR on C33 DSK Help

Started by josemvarona in TMS320c3x19 years ago 1 reply

Hello. I purchased the C33 DSK for a Real-time DSP course, and modified some code found in this post, and using the PCM3003.asm...

Hello. I purchased the C33 DSK for a Real-time DSP course, and modified some code found in this post, and using the PCM3003.asm provided with the kit, to develop a low pass FIR filter. Now, when I run the code I get a garbled signal along all frequency ranges. I tested the Fs(LRCIN) with an oscilloscope to determine whether it was correct, a


Re: Yahoo group for FreePCB open source PCB layout

Started by Keith Larson in TMS320c3x19 years ago 1 reply

Hi, and thanks This may fall into the 'way cool dude' catagory! And, I noticed that Ivex libraries are supported.  I...

Hi, and thanks This may fall into the 'way cool dude' catagory! And, I noticed that Ivex libraries are supported.  I went down the Ivex path because at the time it was the cheap and simple way


Emulator and Software recommendations...

Started by Gene Breniman in TMS320c3x19 years ago 1 reply

I am graduating from my VC33 university DSK board up to my own design (again using the tms320v33). Does any one have any...

I am graduating from my VC33 university DSK board up to my own design (again using the tms320v33). Does any one have any recommendations for emulators and supporting software for this environments (debug and software development)? I would like to maximize functionality


XDS510PP_PLUS with Code COmposer on Windows XP Pro

Started by kk7p in TMS320c3x19 years ago 3 replies

Hi! I purchased the latest version (4.10.36) of CCS for the TMS320VC33. It runs in simulator mode just fine. I also...

Hi! I purchased the latest version (4.10.36) of CCS for the TMS320VC33. It runs in simulator mode just fine. I also purchased an XDS510PP_PLUS and instazlled the latest drivers from the SXPectrum Digital website. When I try to configure CCS to accep


Boot loading doubts in C3x DSP

Started by janarthanan n in TMS320c3x19 years ago 1 reply

Dear sir, I am doing a project using DSPc3x interfaced with SRAM. I came through a problem while using C3x processor without...

Dear sir, I am doing a project using DSPc3x interfaced with SRAM. I came through a problem while using C3x processor without using emulator to Download the program to DSP. What steps i have to take for Boot Loading Program?(I am just writing my program hex code to program memory).


ARE and AWE....

Started by Gene Breniman in TMS320c3x19 years ago 1 reply

I seem to be a little confused. I am attempting to develop a daughterboard for the VC33 university DSK. I can't seem to get...

I seem to be a little confused. I am attempting to develop a daughterboard for the VC33 university DSK. I can't seem to get the ARE and AWE strobes to work. I see them for reads and writes to 0x9FFFFF (I know that this overlaps on-board FPGA), but not for reads and


VC33 DSK

Started by eng_murat in TMS320c3x19 years ago 1 reply

Hi all, I've recently bought a VC33 DSK. I've setup the portio driver for the paralel port and setup the dsk & compiler...

Hi all, I've recently bought a VC33 DSK. I've setup the portio driver for the paralel port and setup the dsk & compiler package that came with the DSK (I'm using WinXP). No the actual question comes. When I run the dsktest.exe it runs normaly and I can see the fft a


Re: [FixedPointDSP] Current Trends in TI HW,Tools & Training

Started by Bhooshan Iyer in TMS320c3x19 years ago

Hi Indrajit- The link that i sent in that mail came split in two different lines in the page. I have posted the complete link here...

Hi Indrajit- The link that i sent in that mail came split in two different lines in the page. I have posted the complete link here including the file name inside the angled braces, so pls use this complete link on you browser instead. Let me know if there are any further difficulties


Starter Kit TMS320C3x in Windows XP

Started by Miszael Montiel in TMS320c3x19 years ago 5 replies

Hi !!! I made an application program in Windows 98, but it does not work in Windows XP, do not work the programs that come...

Hi !!! I made an application program in Windows 98, but it does not work in Windows XP, do not work the programs that come with the StarterKit.I need Algun controller to be able to connect the StarterKit with the PC. Thanks Miszael.


Ask a Question to the DSPRelated community

To significantly increase your chances of receiving answers, please make sure to:

  1. Use a meaningful title
  2. Express your question clearly and well
  3. Do not use this forum to promote your product, service or business
  4. Write in clear, grammatical, correctly-spelled language
  5. Do not post content that violates a copyright