Hi Everyone, I know that MATLAB can convert direct form filters to biquads/SOS DF2 form. I wanted to know if there are any other softwares...

Hi Everyone, I know that MATLAB can convert direct form filters to biquads/SOS DF2 form. I wanted to know if there are any other softwares which can do that. Kindly let me know if anyone knows about any other software. Thanking You Megha --------------------------------- Yahoo! oneSearch: Finally, mobile search that gives answers, not web links.

I use tms320vc549, I have some problems in bootloader and PLL mode, my=20 problems are: 1- In spru131 =E2=80" part 8.5 =E2=80" table 8.15 (Clock...

I use tms320vc549, I have some problems in bootloader and PLL mode, my=20 problems are: 1- In spru131 =E2=80" part 8.5 =E2=80" table 8.15 (Clock mode): when I use = crystal=20 for clocking, which of =E2=80=9Cwith external source=E2=80=9D or =E2=80=9Cw= ith oscillator=20 enabled=E2=80=9D is true? And Does my DSP act by =E2=80=9COption 1=E2=80=9D or =E2=80=9COption2=E2=80= =9D? 2- In spru28...

Hi, I design a board including a TMS320VC5416 and an Am29LV160D (Delay 70ns) flash memory. I connect Data and Address buses of DSP to the flash...

Hi, I design a board including a TMS320VC5416 and an Am29LV160D (Delay 70ns) flash memory. I connect Data and Address buses of DSP to the flash directly and make control signals of flash with MSTRB#, and R/W# of DSP. I observe control signals, data and address buses of flash and all of them it seems are correct; However, I can?t write in a specific position since when I read the position I

Vijay- > didnt even watch the 'To' dropbox! for last 2 times....apologies for that. > > I dont have a debugger :( (programming is thru...

Vijay- > didnt even watch the 'To' dropbox! for last 2 times....apologies for that. > > I dont have a debugger :( (programming is thru SPI bootloader)and > simulaur is not helpful in this matter... > > so i am planning to inspect the example files and thier disassembly > > lets see.... Your manager (or Prof) has to get you a JTAG emulator. There's no way you can be assigned to de

Vijay- > well the basic problem is, CCS is using the registers 0x01, 02....for > passing paramaters when a C fuction is called. i confirmed...

Vijay- > well the basic problem is, CCS is using the registers 0x01, 02....for > passing paramaters when a C fuction is called. i confirmed this by > looking at the dissasembly, after loading the code in CCS.so i thought > that based on the CPL bit state[in application code] the CCS will > decide what to use, stack or relative address, during compilation and > create the code accordingly.

All, hi I design a relatively simple board consisting of a TMS320VC5416, a Flash memory, and a FPGA. I use the Flash to place my...

All, hi I design a relatively simple board consisting of a TMS320VC5416, a Flash memory, and a FPGA. I use the Flash to place my code. To program the flash, I declare it external in data space (DROM = 0). I connect the data and address buses directly from DSP to the Flash memory. Further, I make OE, WE, and CE signals of the Flash using MSTRB#, DS# and R/W# signals of DSP. The MSTRB#,...

Vijay- > Thanks for your help! > If I understand right, you mean to say that > > 1) CCS itself will set the CPL bit during compilation...

Vijay- > Thanks for your help! > If I understand right, you mean to say that > > 1) CCS itself will set the CPL bit during compilation so that the > code produced, will use stack[far address] instead of relative[near] > address to pass parameters CCS assumes the CPL bit is set when compiling C code. It won't do anything to clear CPL. See my comments below about boot code. > 2) My

Vijay- > I work on 5402 dsp and face a strange problem in CCS(ver 3.1). That > was a old project which never used interrupts. Both C and asm...

Vijay- > I work on 5402 dsp and face a strange problem in CCS(ver 3.1). That > was a old project which never used interrupts. Both C and asm files > are there. C for main\algorithm\logic and asm for low level drivers. > No interupt was used in that project. > > Now i want to add a timer interrupt and came to know [thru Simulator] > that when a C funtion is called with parameters, CCS use

hi all i want to use serial eeprom programming mode for 5416 what part number do you recommend for serial...

hi all i want to use serial eeprom programming mode for 5416 what part number do you recommend for serial eeprom ---------------------------------------------------------- ___________________________________________________________ New Yahoo! Mail is the ultimate force in competitive emailing. Find out more at the Yahoo! Mail Championships. Plus: play games and win prizes. http://uk.rd.y...

Hello, I'm trying to implement a cascading iir and here's my code for the first second order z transform. I'm I going about this correctly?...

Hello, I'm trying to implement a cascading iir and here's my code for the first second order z transform. I'm I going about this correctly? My output is good till a particular value and then it starts having problems. Any help or links to a good example would be great! Thanks, Grant float b[3] = {1,2,1}; float a[3] = {1,-1.9985996261556458,0.99952100328066507}; float y[151]={0}; ...