CSL debugging

Started by Chad Albrecht in TMS320c55x16 years ago 1 reply

Is it possible to get (or compile) the 5509 CSL for source (C) debugging in CCS 2.20? I am investigating the support of SD cards by ...

Is it possible to get (or compile) the 5509 CSL for source (C) debugging in CCS 2.20? I am investigating the support of SD cards by the MMC/SD controller. Thanks! Chad


c5509a usb csl

Started by dona...@knudsenengineering.com in TMS320c55x12 years ago 1 reply

Hi Group, I'm trying to send data through a usb in endpoint to a host pc using a linked list. I've been through spru511 backwards and forwards,...

Hi Group, I'm trying to send data through a usb in endpoint to a host pc using a linked list. I've been through spru511 backwards and forwards, and have also looked at the csl source, and I'm still not clear on a couple of points. It would save me a lot of experimentation if someone knew the answers. Specifically: 1. There appear to be three places I can put the byte count - as a postTransaction...


35184784-Re: SYSR address {ID:4791636}

Started by Anonymous in TMS320c55x18 years ago

Perry,     We have verified that what you have found is correct, this is a bug in the CSL.  We'll put this in our next...

Perry,     We have verified that what you have found is correct, this is a bug in the CSL.  We'll put this in our next release of CSL.        We further apologize for any inconvenience this bug has


C5502 UART

Started by d_nacarino in TMS320c55x11 years ago 1 reply

Hi, I am new to the DSS C55x series from TI and I am trying to interface the C5502 with a PC using the UART. I bought the evaluation board...

Hi, I am new to the DSS C55x series from TI and I am trying to interface the C5502 with a PC using the UART. I bought the evaluation board and they show an example code with their BSL. The problem is I want to make use of the CSL and there's nothing about it in terms of examples... Does anyone have an example code on How setup the CSL for the UART on the C5502.. Any code would be appr...


Setting Interrupts without using CSl Libraries

Started by souj...@gmail.com in TMS320c55x13 years ago

Hi, I am working on 5502 processor.I would like to know do use interrupts without using CSl libraries.suppose i have an external interrupt which...

Hi, I am working on 5502 processor.I would like to know do use interrupts without using CSl libraries.suppose i have an external interrupt which i want to continuously poll how do i go about .how do i enable the interruptsand write the code using C code. In the command file I am allocating Memory section as follows : Memory{ VECS: o=0xFFFF00 l=0x000100 } Section{ .vectors> VECS


C5502 CSL Module Support in cdb file

Started by salleehh in TMS320c55x16 years ago

Hi All My freinds>> I have a module of EVM5502 and I use CCS in my devlopment So, My CCS version is latest version from...

Hi All My freinds>> I have a module of EVM5502 and I use CCS in my devlopment So, My CCS version is latest version from TI Update Advisor v2.21 BUT, but the cdb files of c5502 not including any of CSL Module just a list of System......Input/Output


Linking problem with the c5505 CSL...

Started by znll...@gmail.com in TMS320c55x10 years ago 4 replies

Buliding a simple main as this: #include "csl_i2c.h" void main(){ CSL_I2cSetup i2cSetup; I2C_setup(&i2cSetup); } even if I...

Buliding a simple main as this: #include "csl_i2c.h" void main(){ CSL_I2cSetup i2cSetup; I2C_setup(&i2cSetup); } even if I linked the csl header in the build properties, I obtain three errors: errors encountered during linking; "prova.out" not built Linking failed. Check the Console window for details. unresolved symbol _I2C_setup, first referenced in ./main.obj .....


Regarding EMIF Configeration...

Started by malik_arjun_rcr in TMS320c55x18 years ago

Hi all, I am Unable Configure the EMIF using CSL Library.or Using Bios Cnfig file usin GUI configeration.. IF anyone knows...

Hi all, I am Unable Configure the EMIF using CSL Library.or Using Bios Cnfig file usin GUI configeration.. IF anyone knows about this pls Send me details .. 1>How to Configure EMIF using CSL Lib.. 2> How to Configure EMIF using Bios GUI Cnfigeration...


Setting the codec on the TMS320VC5505 ezDsp USB Stick

Started by znll...@gmail.com in TMS320c55x10 years ago 5 replies

I'm trying to create a simple project in which I set the aic3204's registers through the I2c interface by using the CSL. I've tried to learn from...

I'm trying to create a simple project in which I set the aic3204's registers through the I2c interface by using the CSL. I've tried to learn from the aic3204 project in CCS and from the examples in the CSL, but I still have a problem: when the program calls the function I2C_write is generated an error. Debugging I found that the error is generated when the function waits for the codec to pull down...


5509A - Using CSL MMC Module for DMA Transfers

Started by smiffoz in TMS320c55x11 years ago

Hi all, I am trying to connect an SD Card to a 5509A via a McBSP configured for MMC operation using the MMC CSL. I can successfully read...

Hi all, I am trying to connect an SD Card to a 5509A via a McBSP configured for MMC operation using the MMC CSL. I can successfully read and write sectors from/to the SD Card, and retrieve the SD Card status registers, so I think my physical interface is ok. In order to increase my bandwidth, I'd like to utilise the DMA Controller to handle the transfers to/from the SD Card. Th...


C55xx CSL 2.31.00.5 - DMA addressing changed again!

Started by Paul Pignon in TMS320c55x15 years ago 4 replies

We recently upgraded the CSL to 2.31.00.5. This broke code which had been working for month

We recently upgraded the CSL to 2.31.00.5. This broke code which had been working for month


SD card reading problem

Started by ysha...@yahoo.com in TMS320c55x11 years ago

I use TI csl example of SD card in my firmware all codes are correct but i read sth that is not right. what's the problem? ...

I use TI csl example of SD card in my firmware all codes are correct but i read sth that is not right. what's the problem? thanks y...@yahoo.com


DRAM Access

Started by farooq nasim in TMS320c55x16 years ago 1 reply

I am trying to access DRAM interfaced with EMIF in C5510 using DMA with CSL. I have modified the example dma1 that do the same for...

I am trying to access DRAM interfaced with EMIF in C5510 using DMA with CSL. I have modified the example dma1 that do the same for internal SRAM. My code is attached but it does not work. Can anybody tell me what is wrong. Regards Farooq


GPIO module

Started by Ang Teik Boon in TMS320c55x13 years ago

Does anybody know how to use GPIO module in the TMS320vc5510 chip support library module?thanks i am currently having a problem on that..i do...

Does anybody know how to use GPIO module in the TMS320vc5510 chip support library module?thanks i am currently having a problem on that..i do not how to use the csl module. Please help me..with some snippet coding of GPIO initialization..thanks.


mcbsp interrupt problem

Started by in TMS320c55x12 years ago

Hi all,I'm trying to write a program use the receive interrupr in the omap5912 mcbsp1 in the dsp side.I use the CSL in my program,but when the...

Hi all,I'm trying to write a program use the receive interrupr in the omap5912 mcbsp1 in the dsp side.I use the CSL in my program,but when the interrupt occur,it seems that the interrupt services routine don't execute and I can't find what led to that ,any idea about the problem was appreciate.


USB Audio on C5509

Started by Lance Ralph in TMS320c55x17 years ago

Has anyone successfully implemented an audio interface on the 5509 using the USB API in the CSL? We've been unable to locate any...

Has anyone successfully implemented an audio interface on the 5509 using the USB API in the CSL? We've been unable to locate any sample code and have had limited success with our implementations.


T3 reg corrupted; How to find out whodunnit?

Started by David Rick in TMS320c55x15 years ago 4 replies

I'm looking for ideas on how to find a particularly elusive bug. The target is a C5509A using DSP/BIOS, CSL, and DSPlib. ...

I'm looking for ideas on how to find a particularly elusive bug. The target is a C5509A using DSP/BIOS, CSL, and DSPlib. I have a task written in C that runs forever. The compiler has used the T3 register to store an array offset. It initializes T3 prior to t


USB problem

Started by Anonymous in TMS320c55x15 years ago 4 replies

I am developing the USB of C5509. I have configured the USB using the CSL USB and then I have activate the USB module: ...

I am developing the USB of C5509. I have configured the USB using the CSL USB and then I have activate the USB module: USB_init(USB0, cfgArray, 0x80); USB_ConnectDev(USB0) What need I do when the PC send the RESET command? Could anyone help me with a


Regd the DAT_MODULE Functions

Started by Nikhil S. Parvatikar in TMS320c55x16 years ago

Hi C55x group, I am finding it difficult to tranfer data using the DAT Module of the CSL. I am trying to do it for the C5510...

Hi C55x group, I am finding it difficult to tranfer data using the DAT Module of the CSL. I am trying to do it for the C5510 DSK. In my project I have included the csl_dat.h file In the project options i have used the -d"CHIP_5510PG1_0" and include


Re: I2C on 5502

Started by Wei Li in TMS320c55x12 years ago

As you mentioned that DSP is a slaver. Then it's not the problem of 5502 but rather other IC, the master. Wei --- In c...@yahoogroups.com,...

As you mentioned that DSP is a slaver. Then it's not the problem of 5502 but rather other IC, the master. Wei --- In c...@yahoogroups.com, Behrooz Daneshkhah wrote: > > Hi > I don't see anything on Scope.No clock.No data. Even when running CSL > sample code for C5502! > > Behrooz > --- iewil2000 wrote: > > > Did you look at the scope to see