Hi all I want to receive 70 MHz PM+BPSK modulated signal. Video bandwidth:138 kHz Modulation index for PM: 1.2 radian Subcarrier...

Hi all I want to receive 70 MHz PM+BPSK modulated signal. Video bandwidth:138 kHz Modulation index for PM: 1.2 radian Subcarrier frequency of BPSK:65536 Hz. I have been using Matlab /Simulink and TMS320C6713 DSK. 1. I need suitable ADC daughtercard for C6713 DSK. 2. What is the sampling rate according to this spec.s? How can I calculate? I want to proof my calculation method. ...

Hello Everyone, I am currently trying to disply the graph for "adaptIDFIR" (chap 7 of DSP and Applications with the C6713 and C6416 by Rulph...

Hello Everyone, I am currently trying to disply the graph for "adaptIDFIR" (chap 7 of DSP and Applications with the C6713 and C6416 by Rulph Chassaing) but it doesn't graph anything. I am not sure whether windowing option I did was not correct or there's certain options that I missed. I'm using C6713 board. the program was succesfully built but after loading the program when i wanted ...

Hi I noticed that for the C6713/3B DSP there is an internal configurable PLL to generate various clock speeds for DSP core...

Hi I noticed that for the C6713/3B DSP there is an internal configurable PLL to generate various clock speeds for DSP core as well as peripherals. Knowing that, is it of any advantage to route the CLKOUT2/CLKOUT3 pins to ECLKIN of EMIF instead of using the int

Hello, I bought Dr Chassaing's book in 'low price edition' version (available in Indian subcontinent at affordable rates) but it turns out...

Hello, I bought Dr Chassaing's book in 'low price edition' version (available in Indian subcontinent at affordable rates) but it turns out that it does not have the CD-ROM. Ofcourse I bought the book for learning the c6713 kit as I already know & teach DSP using Li Tan's, Ifeacher's and Proakis' book for that. So, I'd appreciate it very much if you can send me the CD rom files ...

Hi all, We develop a TMS320C6713 board. The C6713 code has been tested using XDS510usb JTAG emulator and everything is O.K....

Hi all, We develop a TMS320C6713 board. The C6713 code has been tested using XDS510usb JTAG emulator and everything is O.K. To finalize our system, we switch to HPI boot loading and load the C6713 code using HPI. In the preliminary stages of our code, we

Hi all, my name is alex and I have some problem with c6713 edma. I'm trying to run a project taken from the chapter 5 of the ppt presentation...

Hi all, my name is alex and I have some problem with c6713 edma. I'm trying to run a project taken from the chapter 5 of the ppt presentation by Naim Dahnoun...the project is built correctly but i can't see the output from the codec when I run the .out file. please can someone help me? thank you

PLEASE CAN YOU HELP ME ABOUT a C code for PWM in C6713 DSK because this is my project subject I couldnt find if you can help me I am waiting...

PLEASE CAN YOU HELP ME ABOUT a C code for PWM in C6713 DSK because this is my project subject I couldnt find if you can help me I am waiting your messages or e-mails...(TOO IMPORTANT FOR ME)!! I am a electrics & electronics engineering student... VERY URGENT!!

Hi, I have interfaced a 12-bit ADC with C6713 DSP. How can I scale the output to see the amplitude of the output signal same as of input...

Hi, I have interfaced a 12-bit ADC with C6713 DSP. How can I scale the output to see the amplitude of the output signal same as of input signal ? For example, Amplitude = 2 Vp_p with 5KHz frequency ? I want to run ADC for 5 minutes or more and save all the sampled values in a file to examine them in Matlab ? Can you please tell me how could I do it ? Waiting for your help. BR, B...

the voltage on the c6711-dx-pin was approx. 3,3v, changes to zero and then starts the data-transfer. but now on the c6713-dsk,...

the voltage on the c6711-dx-pin was approx. 3,3v, changes to zero and then starts the data-transfer. but now on the c6713-dsk, it`s always zero, but the DR-pin of the c6713-dsk`s is always 3,3v like the c6711, so when i connect these pins, the voltage is approx. 1,7v with no changing

hi all ! my prof gave me a job to program the C6713-DSK to receive music at the LINE_IN and to transmit it via the McBSP0 or...

hi all ! my prof gave me a job to program the C6713-DSK to receive music at the LINE_IN and to transmit it via the McBSP0 or 1-port to another C6713-DSK -McBSP and finally transmit it to those LINE_OUT. but do i understand the technical reference right, that i can use t

dear ladies and gentlemen ! i need a code to service three C6713-DSKs via EDMA/McBSP in the time division multiplex mode. ...

dear ladies and gentlemen ! i need a code to service three C6713-DSKs via EDMA/McBSP in the time division multiplex mode. because of no time i want to ask if somebody could do it for me, for payment, of course. plz contact me via my privat email-adress. sinc

I tried to run C code generated by using Simulink and Real Time Workshop on Digital Spectrum DSK C6713. I am using CCS 3.3 , Matlab (14P3),...

I tried to run C code generated by using Simulink and Real Time Workshop on Digital Spectrum DSK C6713. I am using CCS 3.3 , Matlab (14P3), Real Time Workshop ver 6. I was able to generate ANSI C successfully. The simulink model I used have only two blocks "Line In C6713 ADC" block directly connected to "Line Out C6713 DAC" with DSKC6713 Traget Preference block. This model suppose to tra...

I tried to run C code generated by using Simulink and Real Time > Workshop on Digital Spectrum DSK C6713. I am using CCS 3.3 , Matlab >...

I tried to run C code generated by using Simulink and Real Time > Workshop on Digital Spectrum DSK C6713. I am using CCS 3.3 , Matlab > (14P3), Real Time Workshop ver 6. I was able to generate ANSI C > successfully. The simulink model I used have only two blocks "Line In > C6713 ADC" block directly connected to "Line Out C6713 DAC" with > DSKC6713 Traget Preference block. This model suppo

Hi folks, I attended the TI Developers Conference last week and picked up the C6713 DSK. This included the DSK version of CCStudio...

Hi folks, I attended the TI Developers Conference last week and picked up the C6713 DSK. This included the DSK version of CCStudio 2.21. I was told at one of the workshops that this version of CCStudio was limited in size of executables that could be produced. My question: What are the l

Dear All I am using c6713 dsk with CCS software. it's sampling frequency minimum 8KHz , max 99KHz & 256 FFT point. I want to process real signal...

Dear All I am using c6713 dsk with CCS software. it's sampling frequency minimum 8KHz , max 99KHz & 256 FFT point. I want to process real signal 0.5Hz to 10 Hz. Is it possible to process or do FFT for this frequency band ? If not, how can i do it ... Your kind help will be highly appreciated. Regards Gopal Sarkar, Kolkata _____________________________________

Hi all, my graduate project is Speech Recognition one. i need to connect my DSK c6713 with matlab simulink. i use matlab 2007b and CCS...

Hi all, my graduate project is Speech Recognition one. i need to connect my DSK c6713 with matlab simulink. i use matlab 2007b and CCS 3.1 there is always an error. and seems like something messing i don't know what?although we follow the steps in MathWork site. by searching we found that's we need ( a daughtercard for the DSK ) witch have serial ports. is that true? prntscr for...

hello everyone,i'm currently having quite a hard time with a certain issue.. i have a laptop equipped with windows Vista and i have bought...

hello everyone,i'm currently having quite a hard time with a certain issue.. i have a laptop equipped with windows Vista and i have bought the C6713 and have installed all the necessary software. and windows does indeed recognize the hardware and says that it is installed properly but the strange thing is that whenever i run the C6713 Diagnostics tool or the Code Composer Studio,it never rea...

Hey Gustl, i am having a problem initializing the I2C module on the C6713 DSK and i really need your help we are sending an address to a...

Hey Gustl, i am having a problem initializing the I2C module on the C6713 DSK and i really need your help we are sending an address to a camera (SLAVE) to change format settings, resolution, frame rate and so on, so we send the address and then the apprpriate data value to that register for the change I see that you have code which follows the same initialization proc, but can you please t...

Hey Gustl, i am having a problem initializing the I2C module on the C6713 DSK and i really need your help we are sending an address to a...

Hey Gustl, i am having a problem initializing the I2C module on the C6713 DSK and i really need your help we are sending an address to a camera (SLAVE) to change format settings, resolution, frame rate and so on, so we send the address and then the apprpriate data value to that register for the change I see that you have code which follows the same initialization proc, but can you please

Hello, I am very new to DSP and the C6713, but I seem to be picking it up pretty fast. I have a question regarding the...

Hello, I am very new to DSP and the C6713, but I seem to be picking it up pretty fast. I have a question regarding the connection of SDRAM and a Flash chip to the C6713. The Spectrum Digital DSK board uses an Altera PLD as the glue logic. I am designing a board that uses