----- Forwarded Message ---- From: Chsekhar Prattipati To: i...@gmail.com Sent: Friday, May 23, 2008 10:19:58 AM Subject: Re: [c6x] Re:...

----- Forwarded Message ---- From: Chsekhar Prattipati To: i...@gmail.com Sent: Friday, May 23, 2008 10:19:58 AM Subject: Re: [c6x] Re: C6727 bootloader help Hi Peter ? thanks for your reply. im using flexds emulator from DSPR. The EEPROM(SERIAL) we are using is connected to DSP through I2C bus. im having a doubt whether SECTION_LOAD command can be used to load data from

I am a newbie in DS prcoessors and have been assigned a project on video/image processing using TMS320DM6437(da vinci) processor..after doing...

I am a newbie in DS prcoessors and have been assigned a project on video/image processing using TMS320DM6437(da vinci) processor..after doing the installations that came along with the cds i find that when i click code composer it gives me a message saying error initialising emulator etc...i tried correcting it with my prof by trying ona different machine ,reinstalling but i vain..what cud b...

Hi, all. I have a problem with a JTAG header. There is a 60 pin JTAG header in DSK for TMS320C6416T (Spectrum Digital). I've checked...

Hi, all. I have a problem with a JTAG header. There is a 60 pin JTAG header in DSK for TMS320C6416T (Spectrum Digital). I've checked whether the 60 pin header works properly using XDS560R JTAG Emulator (14 pin) and 14 pin to 60 pin connector. However, when I ran the Code Composer Studio IDE 3.3, an error message showed up as follow: ----------------------------------------- Error c...

i have my own specific board with dsp ti c6713 if i connect to my board with blackhawk lan560 jtag emulator i can send data from dsp to...

i have my own specific board with dsp ti c6713 if i connect to my board with blackhawk lan560 jtag emulator i can send data from dsp to host using rtdx and using high speed rtdx if i replace the modem in xds560r i can only use rtdx the hsrtdx stucks at at postcfg.s62 in the line : ------------------------- HWI_Obj 1, HWI_RESERVED1, 3, _function, _monitor, _addr, _dataType, _oper...

Hi, all. I'm designing the custom board using TMS320C6416T DSP. I want to run the program on the custom board with JTAG emulator and...

Hi, all. I'm designing the custom board using TMS320C6416T DSP. I want to run the program on the custom board with JTAG emulator and CCS. Is it possible to do this with 'No boot' Mode? My design includes no flash rom, HPI or PCI.

Hi. I've made a custom board using TMS320C6416T. Boot mode is host boot and the board has no HPI or PCI. When I connected the target...

Hi. I've made a custom board using TMS320C6416T. Boot mode is host boot and the board has no HPI or PCI. When I connected the target board to the CCS with XDS560 JTAG emulator, the following error message showed up: ------------------------------------------------------------------- Error connecting to the target: Error 0x80000240/-1147 Fatal Error during: Initialization, OCS, I...

B Casne- > I forgot to mention in my original post: We eliminated the GEL files, > and incorporated the necessary EMIF initialization from...

B Casne- > I forgot to mention in my original post: We eliminated the GEL files, > and incorporated the necessary EMIF initialization from there into > the user_init called by the bios before it calls _main. I would not do this. We've encountered issues before with DSP/BIOS 'doing things' with memory prior to user_init(), so placing EMIF init there may not have the desired fail-safe eff

Hi again, I probably succeed to install correctly windows drivers and now device performs the reset via its tool, giving: "SEED USB2.0 XDS510...

Hi again, I probably succeed to install correctly windows drivers and now device performs the reset via its tool, giving: "SEED USB2.0 XDS510 CARD IS RESET, HARDWARE VERSION 1" I installed SEED drivers for CCS but now I've problems with CCS setup. I tried to connect TWO different boards, both with TMS320C6424 (C64x+) with direct JTAG connection. A board was working and the other is brand new t...

hello moto~~ a joke first~:) i got the same problem with the c6720 emulation operation just like what peter described.the run button works,but...

hello moto~~ a joke first~:) i got the same problem with the c6720 emulation operation just like what peter described.the run button works,but the code just can`t load into the target curretly.here`s the asm code displayed in the asm window after the EMULATOR set connected in the ccs.the first line is where the green arrow pointed to. ?00001DDC 00008000 NOP 5 00001

After having the emulator problem solved,I start to work in programming the PLL and the Mcasp register.The PLL work has been done. when...

After having the emulator problem solved,I start to work in programming the PLL and the Mcasp register.The PLL work has been done. when configring the MCASP port ,there one part I dont quite understand how it works,that is ,the FORMAT CONTROL UNIT.According to the SPRU878B file,this unit has two registors use to control the transmit and recieve data format named as X/RFMT and X/RMASK. for ex...

In a hardware design with c6713, I want to use xds560r as emulator as you known. My design is different with dsk6713, therefore how can I used...

In a hardware design with c6713, I want to use xds560r as emulator as you known. My design is different with dsk6713, therefore how can I used xds560r? What changes must be down in setup CCS? Appreciate for any support. Regards Zahra

Hi, I have also the same problem but with TMS3206716 DSK. It doesn't work also for me. I have uninstalled all components and CCS v3.1 and...

Hi, I have also the same problem but with TMS3206716 DSK. It doesn't work also for me. I have uninstalled all components and CCS v3.1 and installed at first CCS v3.3 and then this you propose of Spectrum Digital. Do you know if it has to do with the operating system? I use Windows XP SP3. The error it shows me is: Error initializing emulator I/O Port = 540 Board Name: DSK6416 ...

Hi, I will have to work on a custom board with davinci tms320dm6446 processor on it. I am a bit confused regarding the emulators which i will...

Hi, I will have to work on a custom board with davinci tms320dm6446 processor on it. I am a bit confused regarding the emulators which i will have to use. My questions are following : 1) Will i need an emulator (spectrum digital, 20 pin cti, xds510 or xds560) for downloading my code for the processor and also for burning the flash? I am a bit confused that are these emulators ( xds56...

Dear Sir, We have designed our custom board around TMS320DM6446 DSP+CPU and have bought XDS560R USB emulator from Spectrum Digital,...

Dear Sir, We have designed our custom board around TMS320DM6446 DSP+CPU and have bought XDS560R USB emulator from Spectrum Digital, Alongwith TI CCS3.3 (we bought CCS3.3 alongwith XDS560r from spetrum digital). Follwing are our hardware jumper settings for our board: COUT0 = 0 COUT1 = 1 COUT2 = 1 COUT3 = 1 YOUT[4:0] = 1111 JTAG EMU0 and EMU1 pins are connected with DSP EMU0 a...

Greeting Has anyone ever used the TI TMS470 chip with the XDS510 and CCS?? I connect my XDS510 to the TI TMS470. In CCS the emulator connects...

Greeting Has anyone ever used the TI TMS470 chip with the XDS510 and CCS?? I connect my XDS510 to the TI TMS470. In CCS the emulator connects to the target board but I can't read any memory address at all. I am not sure if I connect the Jtag in the right way (I connected it as I connect to the TMS320C6722), Does anyone have a schematic or can give me a hand on this issue? Thanks in advance. ...

Hi Peter, i´m using the emulator XDS510 USB PLUS from Spectrum Digital. _____________________________________

Hi Peter, i´m using the emulator XDS510 USB PLUS from Spectrum Digital. _____________________________________

Hello, I've problem connecting the target via CCS 3.3 . I use JTAG adapter to connect to target in which I set the switches to default...

Hello, I've problem connecting the target via CCS 3.3 . I use JTAG adapter to connect to target in which I set the switches to default state(ie. All OFF state) It give the following error: Error connecting to the target: Error 0x80000240/-180 Fatal Error during: Initialization, OCS, This error was generated by TI's USCIF driver. SC_ERR_CTL_NO_TRG_POWER The con

Hello, I've problem connecting the target via CCS 3.3 . I use JTAG adapter to connect to target in which I set the switches to default...

Hello, I've problem connecting the target via CCS 3.3 . I use JTAG adapter to connect to target in which I set the switches to default state(ie. All OFF state) It give the following error: Error connecting to the target: Error 0x80000240/-180 Fatal Error during: Initialization, OCS, This error was generated by TI's USCIF driver. SC_ERR_CTL_NO_TRG_POWER The contro

All- The original link given for the "LT430" XDS510-compatible JTAG emulator (subject of this thread) was on a website labeled Litian Co...

All- The original link given for the "LT430" XDS510-compatible JTAG emulator (subject of this thread) was on a website labeled Litian Co (Harbin, CHN). The website hasn't been working for a couple of days now... does anyone know if the site has moved? -Jeff Michael Dunn wrote: > > pco73, > > see multiple comments in line below. > > mikedunn > > On Sun, Jun 28, 2009 at 8:51

I am using DM6446 and xds560 emulator. Can I use ARM's assemble language to debug ARM in CCS?? I write a simple program in CCS ...

I am using DM6446 and xds560 emulator. Can I use ARM's assemble language to debug ARM in CCS?? I write a simple program in CCS using ARM's assemble language. But when compile it , I get mang errors in the output window of CCS. I just want to use ARM's assemble language to read and write ARM's register. Is there some document I can refer to?? _______...