DSPRelated.com

Failed Software Reset: Error 0x00000028/-1076

Started by z_11...@yahoo.com in TMS320c6x15 years ago 2 replies

In a new design with C6713, connecting to CCS is successful, Oscillator and capacitors, some required resistor and EMI filter and buffer of...

In a new design with C6713, connecting to CCS is successful, Oscillator and capacitors, some required resistor and EMI filter and buffer of emulator assembled on board due to test and debug be easier. No external flash or SDRAM assembled and emulator is xds560. during a simple program, when loading .cinit to 0x2960 one error occurred:? data verification failed at 0x2960 please verify targ


TCI6488 JTAG emulation conection problem.

Started by jeev...@yahoo.co.in in TMS320c6x14 years ago 1 reply

Hi All, Our board(Product) has TCI6488 processor. We have a blackhawk JTAG emulator. we have installed the CCS V3.3 with SR12 patch and...

Hi All, Our board(Product) has TCI6488 processor. We have a blackhawk JTAG emulator. we have installed the CCS V3.3 with SR12 patch and installed the JTAG driver. While we are trying to open the emulator debugger and tried to connect to the target it shows the below error message. Error connecting to the target: Error 0x80002240/-183 Fatal Error during: Initialization, OCS, Control, Thi...


Error message when I profile a loop using a emulator.

Started by Li Bing in TMS320c6x19 years ago

Hi, all DSP friends. I am using XDS510PP emulator connected with a DSP board. I have a code which can be run successfully on the...

Hi, all DSP friends. I am using XDS510PP emulator connected with a DSP board. I have a code which can be run successfully on the target DSP. When I try to profile a loop, enable a loop in the profile setup. An error message appeared as following.Anybody can give me some hint. Can't Set Breakpoint at 0x836f4: Error 0x00000008/-1076 E


YUHUA XDS510 USB 2.0 Emulator

Started by scia...@inwind.it in TMS320c6x16 years ago 1 reply

Hi everybody, I'm a newbye in DSP development. I just buyed a XDS510 USB 2.0 "manufactured" by YUHUA Electronics from an ebay Honk...

Hi everybody, I'm a newbye in DSP development. I just buyed a XDS510 USB 2.0 "manufactured" by YUHUA Electronics from an ebay Honk Kong reseller. Furnished windows drivers are from "SEED International" and seems to be installed correctly. But the Emulator Reset Utility can't reset the device, signaling me "SEED USB2.0 XDS510 CARD RESET FAILED, ffff". Repeating the reset command while the emu...


=?x-unknown?B?Q2FuwrR0?= configure the DSP TMS320C6745

Started by lram...@cidesi.mx in TMS320c6x15 years ago 1 reply

Hi Has anyone ever used the TMS320C6745? I can´t configure it? I open the Code Composer Studio Setup and create a board, i choose...

Hi Has anyone ever used the TMS320C6745? I can´t configure it? I open the Code Composer Studio Setup and create a board, i choose the SD510USB Emulator (I´m working with the XDS510 USB PLUS Emulator)and i also choose the processor type c6745 which includes an ICEPICK_C and the TMS320C674XP. When the setup is finished i save and quit and the Code Composer Studio starts. The problem comes ...


Re: Cannot run TI CC 4.10 with Spectrum SPI530 Emulator in Windows XP

Started by Jeff Brower in TMS320c6x15 years ago

Bob- > We are experiencing one major problem when using C3x/C4x Code Composer 4.10 > and the Spectrum Digital SPI530 MPSD Emulator on PCs...

Bob- > We are experiencing one major problem when using C3x/C4x Code Composer 4.10 > and the Spectrum Digital SPI530 MPSD Emulator on PCs running Windows XP. > We have always run under Windows 2000 and never experienced the following > error. > > While we can successfully connect to a target C30 DSP, reset the DSP, view > DSP memory and internal registers, modify memory locations and l


Cannot run TI CC 4.10 with Spectrum SPI530 Emulator in Windows XP

Started by rche...@altrionet.com in TMS320c6x15 years ago 5 replies

Hi All, We are experiencing one major problem when using C3x/C4x Code Composer 4.10 and the Spectrum Digital SPI530 MPSD Emulator on PCs running...

Hi All, We are experiencing one major problem when using C3x/C4x Code Composer 4.10 and the Spectrum Digital SPI530 MPSD Emulator on PCs running Windows XP. We have always run under Windows 2000 and never experienced the following error. While we can successfully connect to a target C30 DSP, reset the DSP, view DSP memory and internal registers, modify memory locations and load symbols, we c...


XDS510-USB2.0 + C6727 - Load Program problem

Started by pco7...@libero.it in TMS320c6x15 years ago 1 reply

Hi all, I have a XDS510-USB2.0 TI DSP Emulator as "http://www.lt430.com/ProductShow.asp?ID=109" and a custom board with dsp C6727. I have...

Hi all, I have a XDS510-USB2.0 TI DSP Emulator as "http://www.lt430.com/ProductShow.asp?ID=109" and a custom board with dsp C6727. I have installed CCS3.3.54.1 and I have used CCS Setup to add "C672x XDS510 Emulator" to my system configuration. This configuration provides a BYPASS_0 processor type and a TMS320C6720_0 processor type with driver "tixds6000.drv". I have changed Property/Configurat...


Code Composer/Emulator error

Started by bogdan in TMS320c6x18 years ago

Dear All, Fatal Error during: Execution, Target Communication, Control,  Device driver: Lost USB connection...

Dear All, Fatal Error during: Execution, Target Communication, Control,  Device driver: Lost USB connection to emulator. You should ABORT and restart


Re: Can't configure the DSP TMS320C6745

Started by lram...@cidesi.mx in TMS320c6x15 years ago

Hi Peter, i´m using the emulator XDS510 USB PLUS from Spectrum Digital. _____________________________________

Hi Peter, i´m using the emulator XDS510 USB PLUS from Spectrum Digital. _____________________________________


DM642 EVM Flash

Started by jeko...@gmail.com in TMS320c6x16 years ago 1 reply

Hi all, is it possible to program flash memory without a Jtag Emulator (eg. with PCI Valley Tech driver)? Thanks

Hi all, is it possible to program flash memory without a Jtag Emulator (eg. with PCI Valley Tech driver)? Thanks


Re: SEED USB emulator with 67xx devices -- will pay for solution

Started by Andrew Nesterov in TMS320c6x17 years ago

> http://www.seeddsp.com/default.php#2 I browsed there and had a sudden dejavu attack :) Cheers, Andrew

> http://www.seeddsp.com/default.php#2 I browsed there and had a sudden dejavu attack :) Cheers, Andrew


Re:++WINTECH+TDS510PLUSE+Jtag+Emulator

Started by J J in TMS320c6x14 years ago 1 reply

Dear All Very thanks for your advises, I can program c6455 DSK with Wintech TDS560 but Wintech TDS510plus does not work.

Dear All Very thanks for your advises, I can program c6455 DSK with Wintech TDS560 but Wintech TDS510plus does not work.


TMS 320c6x evm problem

Started by Asadullah Khan in TMS320c6x20 years ago

Hi there do any of you have any idea how to reprogram the EEPROM in TMS320c6x Evaluation module with using emulator Regards,...

Hi there do any of you have any idea how to reprogram the EEPROM in TMS320c6x Evaluation module with using emulator Regards, _______________________________________________________________ " ....In the province of the MIND, what one BELIEVES to be TRUE


Problem in Writing into peripheral Reg.

Started by simha j in TMS320c6x22 years ago

Hi all, I am using CCS2.0 and spectrum digital driver for xds510pp plus emulator. I am trying to Write into the EMIF...

Hi all, I am using CCS2.0 and spectrum digital driver for xds510pp plus emulator. I am trying to Write into the EMIF registers through HPI. But it is not getting updated. How to do this?? What else I need to care??? In my set up, I have StrongARM as t


TMS320DM6437

Started by arun_narain2005 in TMS320c6x16 years ago 1 reply

I am a newbie in DS prcoessors and have been assigned a project on video/image processing using TMS320DM6437(da vinci) processor..after doing...

I am a newbie in DS prcoessors and have been assigned a project on video/image processing using TMS320DM6437(da vinci) processor..after doing the installations that came along with the cds i find that when i click code composer it gives me a message saying error initialising emulator etc...i tried correcting it with my prof by trying ona different machine ,reinstalling but i vain..what cud b...


Breakpoint error

Started by mayank agarwal in TMS320c6x19 years ago 2 replies

Hi all, I am getting the following error while i am trying to run the program after loading it in memory.Is there any TI document which...

Hi all, I am getting the following error while i am trying to run the program after loading it in memory.Is there any TI document which explains why this error is occuring again and again.I am using DM642 emulator board with CCS version 2.1 Breakpoint Manager: Some breakpoints are not at valid lines. Code Composer has moved these breakpoi


H/W simulator gap

Started by Sri in TMS320c6x19 years ago 3 replies

Hi All, I am trying to run a video codec on c64x How much it is logical to have a gap between emulator and simulator. up to...

Hi All, I am trying to run a video codec on c64x How much it is logical to have a gap between emulator and simulator. up to what order they can be bridged. what are the things need to taken care of to minimise this gap. -- Regards Sri


Booting with Custom Board

Started by shad...@yahoo.com in TMS320c6x16 years ago 1 reply

Hi, all. I'm designing the custom board using TMS320C6416T DSP. I want to run the program on the custom board with JTAG emulator and...

Hi, all. I'm designing the custom board using TMS320C6416T DSP. I want to run the program on the custom board with JTAG emulator and CCS. Is it possible to do this with 'No boot' Mode? My design includes no flash rom, HPI or PCI.


gap between emulator and simulator?

Started by qing_lee73 in TMS320c6x20 years ago 1 reply

Hi there, Just found this forum. Very glad to know there are so many friends discussing C6x DSP. We have been using C6416...

Hi there, Just found this forum. Very glad to know there are so many friends discussing C6x DSP. We have been using C6416 to develop a video encoder for a long time. A problem kept confusing us, which is the execution time on simulator is quite different from the