Dear All, Fatal Error during: Execution, Target Communication, Control,  Device driver: Lost USB connection...

Dear All, Fatal Error during: Execution, Target Communication, Control,  Device driver: Lost USB connection to emulator. You should ABORT and restart

Hi guys, Presently i am having DM642EVM Board with me. I am having CCS2.2 and also i followed the steps they were present in...

Hi guys, Presently i am having DM642EVM Board with me. I am having CCS2.2 and also i followed the steps they were present in the "dm642evm_QuickStartGuide". After installing the patches and "SdConfig C6000 v2.2x" i am not getting the emulator to run. After all installation i started with "Setup CCS 2", then i imported EVMDM642XDS510USB Emulator. Then while starting the CCS2.2 it is...

Hello everybody. I'm trying to use XDS510PP Jtag emulator with a DM642 EVM. It doesn't work, and the utility sdconfig when I try to reset the...

Hello everybody. I'm trying to use XDS510PP Jtag emulator with a DM642 EVM. It doesn't work, and the utility sdconfig when I try to reset the emulator give me the "Invalid port configuration" signal. The output of Configuration-> port available give me $$ Printer port available at: $$ EmuPortAddr=0x378 $$ EmuPortMode=SPP8 $$ EmuPortSpeed=0 The sdopt.cfg file contains: # ============

Hi to all, I am going to post a question that may sound stupid, but I haven't been able to find out the answer. I have...

Hi to all, I am going to post a question that may sound stupid, but I haven't been able to find out the answer. I have configured correctly my dsk6713 and it works. I also have an XDS560 POD that is correctly connected to the PC. The question is: Is always necessary that the POD cable is connected to the DSK by the JTAG port?? Can the emulator works without this conection...

Hi All, We have designed a custom board with TMS320C6414T processor on board. We are using a JTAG emulator from GAO Tech Canada, for...

Hi All, We have designed a custom board with TMS320C6414T processor on board. We are using a JTAG emulator from GAO Tech Canada, for programimg the processor. The JTAG emulator does not connect to the processor, and gives the following error. ------------------------------------------------------------------------------- Error connecting to the target: Error 0x80000240/-121 Fatal Err...

Hi, I've spectrum digital's XDS560 emulators, that I use for 6416 DSPs. As we know, JTAG is a IEEE standard(IEEE1149.1)....

Hi, I've spectrum digital's XDS560 emulators, that I use for 6416 DSPs. As we know, JTAG is a IEEE standard(IEEE1149.1). Then, why we can't use the same emulator with IDEs of different vendors for different processors? Thanks and Regards, Veeresh

Hello, I was looking for some information about emulators and i found this thread. Just one simply question ¿what is a SEED USB emulator? Thank...

Hello, I was looking for some information about emulators and i found this thread. Just one simply question ¿what is a SEED USB emulator? Thank you, regards Miguel Ángel Jeff, > > Sorry about the top posting. I only have 'very low tech' access at the moment and this is just a pasted text file. > > I will try to make this generic for 'cannot connect problems with NON spectrum digital emul

Miguel- > Hello, I was looking for some information about emulators and i found > this thread. Just one simply question: what is a SEED USB...

Miguel- > Hello, I was looking for some information about emulators and i found > this thread. Just one simply question: what is a SEED USB emulator? http://www.seeddsp.com/default.php#2 -Jeff > > Sorry about the top posting. I only have 'very low tech' access at the moment and this is just a pasted text file. > > > > I will try to make this generic for 'cannot connect problems wit

Hi All!    i have a query , Can i download the code on target Board  with out using the Emulator , is it through Serial port then which...

Hi All!    i have a query , Can i download the code on target Board  with out using the Emulator , is it through Serial port then which Driver Software will be needed for it? thanx in advance swapnali   How much free photo storage do you get? Store your friends n family photos for FREE with Yaho

> http://www.seeddsp.com/default.php#2 I browsed there and had a sudden dejavu attack :) Cheers, Andrew

> http://www.seeddsp.com/default.php#2 I browsed there and had a sudden dejavu attack :) Cheers, Andrew

Hi, I am using a GaoTek USB XDS510 with CCS 3.3 to do development on an Innovative Integration C6713 based board. After following setup...

Hi, I am using a GaoTek USB XDS510 with CCS 3.3 to do development on an Innovative Integration C6713 based board. After following setup instructions in the manual I get the following error in CCS starting up "Fatal Error during : OCS SC_ERR_OCS_PORT " What does this mean? I have run xdsprobe -f gao.cfg -p -x240 -r -v and the emulator claims to reset successfully. I have

Dear all Let me to explain my problem. I want to use JTAG for connect target (C6713 board not C6713DSK) and emulator. I have a big program and I...

Dear all Let me to explain my problem. I want to use JTAG for connect target (C6713 board not C6713DSK) and emulator. I have a big program and I want to save total of program on flash, then by secondary boot loader copy them to IRAM on DSP for running. How can I program flash? Is Gel file programmed on flash? Is it possible to program flash on board by DSP? For have a secondary boot loading, ...

Hi everybody, I am new to dsp. I just received an XDS510 USB JTAG Emulator. I also have a Valde Systems VS1501 Board, which is based on the...

Hi everybody, I am new to dsp. I just received an XDS510 USB JTAG Emulator. I also have a Valde Systems VS1501 Board, which is based on the TMS320DM642 Processor. I installed the XDS drivers and went to CCSv3.3 Setup to Configure the board. I used the following configuration: C64xx Rev 1.1 XDS510-USB Board Driver Location: C:\CCStudio_v3.3\drivers\sdgo6400usb_11.dvr Diagnostic Utilit...

Hi, If anyone using the TI Davinci platform, would you please comments on the development platform. Is it that ccs+ emulator is used for the...

Hi, If anyone using the TI Davinci platform, would you please comments on the development platform. Is it that ccs+ emulator is used for the development. TI wedsite shows that the development board has a harddisk on it. what is the purpose of that. I am looking for a platform to evaluate our dsp algorithm to see if it meets the power and speed requirement. As i am new in this field, i do no...

Hi, I have Video Encoder running on DM6446 Eval board (Downloaded DSP image through xds-560 Blackhawk Emulator). I do file I/O to run my...

Hi, I have Video Encoder running on DM6446 Eval board (Downloaded DSP image through xds-560 Blackhawk Emulator). I do file I/O to run my code on DSP side. Now I am trying to prepare the Davici image to run the codec to take real-time data which is available via EPSI. When I looked into SDK package, they have a dummy video enc code , which does simple copy of input to output. I have p...

Hi all, is it possible to program flash memory without a Jtag Emulator (eg. with PCI Valley Tech driver)? Thanks

Hi all, is it possible to program flash memory without a Jtag Emulator (eg. with PCI Valley Tech driver)? Thanks

Hi Mike, We are using DM640-based custom boards with XDS510 PP Emulator. During production, some of our boards do not seem to connect...

Hi Mike, We are using DM640-based custom boards with XDS510 PP Emulator. During production, some of our boards do not seem to connect with CCS while some of them do. We have checked the hardware connections and JTAG signals of these boards with those that are working and they seem similar. We tested the boards using SDConfig utility and it is able to detect scan path and is able t...

Hi, I am using the processor 6211 on my customized board. Using the emulator XDS510PP Plus at JTAG. I want to get the Chip Select Pulses at the...

Hi, I am using the processor 6211 on my customized board. Using the emulator XDS510PP Plus at JTAG. I want to get the Chip Select Pulses at the CE2. Using the Host port Interfacing by putting HD3:HD4 pins at 0,0 (HD:4 through the pull down resister, 0.3V). No external memory is mounted yet now, Memory presented on board is On-Chip memory Step: 1 I prepared the .cmd file, that is working f...

I am a newbie in DS prcoessors and have been assigned a project on video/image processing using TMS320DM6437(da vinci) processor..after doing...

I am a newbie in DS prcoessors and have been assigned a project on video/image processing using TMS320DM6437(da vinci) processor..after doing the installations that came along with the cds i find that when i click code composer it gives me a message saying error initialising emulator etc...i tried correcting it with my prof by trying ona different machine ,reinstalling but i vain..what cud b...

----- Forwarded Message ---- From: Chsekhar Prattipati To: i...@gmail.com Sent: Friday, May 23, 2008 10:19:58 AM Subject: Re: [c6x] Re:...

----- Forwarded Message ---- From: Chsekhar Prattipati To: i...@gmail.com Sent: Friday, May 23, 2008 10:19:58 AM Subject: Re: [c6x] Re: C6727 bootloader help Hi Peter ? thanks for your reply. im using flexds emulator from DSPR. The EEPROM(SERIAL) we are using is connected to DSP through I2C bus. im having a doubt whether SECTION_LOAD command can be used to load data from