Hi all, How to profile a c-function in the emulation mode?? I am connected to a custom board thro'h Parallel Jtag emulator. ...

Hi all, How to profile a c-function in the emulation mode?? I am connected to a custom board thro'h Parallel Jtag emulator. In DSP/BIOS user's guide, under STS module it is given that how to use it for profiling. I covered my function to be profiled between STS_set

Hi everybody, We made a board with a 6211 dsp. To debug it we use the XDS510PP emulator via JTAG. As a testbed, we used a 6711...

Hi everybody, We made a board with a 6211 dsp. To debug it we use the XDS510PP emulator via JTAG. As a testbed, we used a 6711 dsk. To program the rom on the dsk, ti provides a flash programming utility which downloads the hex file to the rom. Unfortunately it works only with t

Just in case anyone HAPPENS to be working through the XMas break like me, I have a question concerning multiple-dsp setup. I...

Just in case anyone HAPPENS to be working through the XMas break like me, I have a question concerning multiple-dsp setup. I setup Code Composer Studio 1.23 in a three 6203 DSPs configuration, Im also using Spectrum Digital's SPI515 Parallel Port Emulator. Physically, th

Hi, I need to set up a PC to program the flash on a custom 6711 board using a JTAG emulator. FlashBurn appears to require CCS...

Hi, I need to set up a PC to program the flash on a custom 6711 board using a JTAG emulator. FlashBurn appears to require CCS 2.1 I really don't want to give our production department a full version of CCS. Is there anyway to use FlashBurn without CCS or does TI have a standal

Hi, SOS on followed problem, thanks lot in advance! I am using TMS320C6711B with XDS560 emulator. The problem now is the CCS 2.10...

Hi, SOS on followed problem, thanks lot in advance! I am using TMS320C6711B with XDS560 emulator. The problem now is the CCS 2.10 can't start up,the error message is: Can't initialize the target CPU: 1. Target initialize failed <-1200> 2. Check

Following was the problem noticed with the DSK: C6711 DSK - After connecting it with DB15 connector when i try to run code...

Following was the problem noticed with the DSK: C6711 DSK - After connecting it with DB15 connector when i try to run code composer in DSK mode, it does not pop up and report the error as 'can't initialize the target'. But if i plug in the emulator cable on the Jtag of

Subramanyam_sig- It sounds like CCS is having a hard time to control some signals, maybe the DSP Reset signal. You might...

Subramanyam_sig- It sounds like CCS is having a hard time to control some signals, maybe the DSP Reset signal. You might check the SMC chip (U10) for a bent or loose pin. What you might try is another board, without any change in cable, emulator, software, e

Hi, We have a customer using the C6416 TEB with an emulator and CCS. He is trying to run the first simple DSP/BIOS example and...

Hi, We have a customer using the C6416 TEB with an emulator and CCS. He is trying to run the first simple DSP/BIOS example and use Log_printf() to print "Hello World". The code seems to run OK but nothing is printed to the Message Log. Has anyone got any ideas

Hello: Recently bought a IEKC64x board from ATEME. I would like to use it as stand-alone and connect to the PC's parallel...

Hello: Recently bought a IEKC64x board from ATEME. I would like to use it as stand-alone and connect to the PC's parallel port just as I use the C6711 DSK (i.e. use CCS and download *.out files to the board and run) ; but there is no embedded emulator like in the 6711DS

Hi, We are having problems to download the .out when using XDS560 emulator. We have a C6203 board and when we try to...

Hi, We are having problems to download the .out when using XDS560 emulator. We have a C6203 board and when we try to download the .out to the DSP via XDS560, a message appears warning that the endianess of the target is different from the endianess of the .out. The DSP

Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate...

Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate jumper settings on the board, which gives the video output and LEDs ON as described on the installation guide. (meaning the hardware is connected

I have designed a board which has two C6711 on it.But i can not perform emulation. My emulator is EPP_XDS510. The port is 0x378....

I have designed a board which has two C6711 on it.But i can not perform emulation. My emulator is EPP_XDS510. The port is 0x378. When I detect the board with SDConfig. The result of verify command is: $$ EmuPortAddr=0x378 $$ EmuPortMode=EPP $$ ProductId=90

I have designed a board around TI's C6711. I am trying to perform emulation under CCS 2.20 using the spectrum's XDS510PP emulation...

I have designed a board around TI's C6711. I am trying to perform emulation under CCS 2.20 using the spectrum's XDS510PP emulation POD. The "SDConfig" finds and passes the Jtag chain with results like: ** Emulator Test ** $$ EmuProductName=XDS510PP $$ Emu

Hi there do any of you have any idea how to reprogram the EEPROM in TMS320c6x Evaluation module with using emulator Regards,...

Hi there do any of you have any idea how to reprogram the EEPROM in TMS320c6x Evaluation module with using emulator Regards, _______________________________________________________________ " ....In the province of the MIND, what one BELIEVES to be TRUE

hello !  i got a big problem when emulating my own board. this is my emulating evironment:               CCS2.2 ...

hello !  i got a big problem when emulating my own board. this is my emulating evironment:               CCS2.2        PCI emulator card with JTAG      &nb

Hello friends: I installed the XDS560 emulator (TI) with and ATEME IEKC64x board, and the XDS560 driver is randomly...

Hello friends: I installed the XDS560 emulator (TI) with and ATEME IEKC64x board, and the XDS560 driver is randomly bluescreening my computer. actually it used be more rampant, until I unchecked the 'RTDX' from "Help" -"About" -> "Component Manager&

Hi all: I am using Cx6205 chip, CCS 2.2 and XDS510 Emulator. My program ran correctly on the simulator but it cannot go main ...

Hi all: I am using Cx6205 chip, CCS 2.2 and XDS510 Emulator. My program ran correctly on the simulator but it cannot go main when it comes to the target board. And I found it traps in some asm codes of a function named _memcpy().I had include the rts.lib in my project. Pl

Hi,all: me again! This time I got another question! I am using Emulator XDS510 which is connected with my target board (after...

Hi,all: me again! This time I got another question! I am using Emulator XDS510 which is connected with my target board (after tested on the simulator correctly). When I loaded my program to the target, sometimes I got error message "Data varification failed at address 0x0

Hi there, Just found this forum. Very glad to know there are so many friends discussing C6x DSP. We have been using C6416...

Hi there, Just found this forum. Very glad to know there are so many friends discussing C6x DSP. We have been using C6416 to develop a video encoder for a long time. A problem kept confusing us, which is the execution time on simulator is quite different from the

Hi all, It's nice to see many problems being discussed openly. I'm a new member. Due to some error in simulation, we...

Hi all, It's nice to see many problems being discussed openly. I'm a new member. Due to some error in simulation, we had to uninstall CCS. I would be of great help if you could solve the problem installing CCS 1.0 with XDS 510 emulator for dyat