HAI GUYS IAM USING C6202 AND CCS1.2 FOR MY APPLICATION. I FLASHED MY APPLICATION, IT WLL BOOT WELL AND WORKS FINE WHEN U...

HAI GUYS IAM USING C6202 AND CCS1.2 FOR MY APPLICATION. I FLASHED MY APPLICATION, IT WLL BOOT WELL AND WORKS FINE WHEN U CONNECT JTAG AND RUN, IF U REMOVE JTAG AND RESET THE BOARD IT WON'T WORK. THERE IS NO PROBLEM IN RESET AND BOOTING PROCEDURE........ , any idea?

I am using a JTAG connector to program the C6711BGFN DSP chip situated as a module on the PC-104 data acquisition board our company ...

I am using a JTAG connector to program the C6711BGFN DSP chip situated as a module on the PC-104 data acquisition board our company developed. When I step through a program using TI Code Composer, the program hangs whenever the EMIF registers are accessed. Is this problem

Dear c6x: I am a grad student working on TMSC6202. And I design a 6202 PCB. The PCB can not work. The main problem is the JTAG can...

Dear c6x: I am a grad student working on TMSC6202. And I design a 6202 PCB. The PCB can not work. The main problem is the JTAG can not work correctly. I use ALVC16245 as JTAG buffer. And I use pullup resistance on EMU0(pin 13), EMU1(pin 14),TMS(pin 1),TDI(pin 3),TDO(pin 7). Th

Gagan- > I guess better put the TI device as first > CPU in the boundary scan chain. This might help. I > only run homogenous...

Gagan- > I guess better put the TI device as first > CPU in the boundary scan chain. This might help. I > only run homogenous mix of 8 TI DSPs in single chain. > But havn't try on the hetrogenous mix of other CPUs > Other thing is to slow the JTAG clock fr

The JTAG port is used both for debugging software in development and for boundary scan hardware test in production. Most of the PLD...

The JTAG port is used both for debugging software in development and for boundary scan hardware test in production. Most of the PLD vendors provide support in their programming software for other devices in the scan chain. But I have received mixed advice on putting TI DSPs in a scan chain

Hi C6x DSP group, I am looking for Spectrum Digital XDS510 USB JTAG Emulator (Used). Please let me know where can I get used emulator. I...

Hi C6x DSP group, I am looking for Spectrum Digital XDS510 USB JTAG Emulator (Used). Please let me know where can I get used emulator. I searched eBay, but could not find it. If anyone is planning to sell it at low price, then please let me know. Thanks and Regards, jigs_dsp India.

Hello everybody, I use a XDS510PP plus JTAG emulator by Spectrum Digital, but the diagnostic give me the following erro: ** Emulator Scan...

Hello everybody, I use a XDS510PP plus JTAG emulator by Spectrum Digital, but the diagnostic give me the following erro: ** Emulator Scan Test -- WriteVal1 0001, ReadVal1 ffff -- WriteVal2 fffe, ReadVal2 ffff -- WriteVal1 0002, ReadVal1 ffff -- WriteVal2 fffd, ReadVal2 ffff -- WriteVal1 0004, ReadVal1 ffff -- WriteVal2 fffb, ReadVal2 ffff -- WriteVal1 ...

Hello experts, I am listing below a problem that I am stuck with for 4-5 days now. Could you please go through it and give suggestions or lead...

Hello experts, I am listing below a problem that I am stuck with for 4-5 days now. Could you please go through it and give suggestions or lead me to someone in your contact list who might have experience in related issues? Our target board is based on the DM640 and we have designed its JTAG circuitry exactly as in the DM642 EVM. We are using the 14- pin JTAG connector connected to a XDS5...

Hello experts, I am listing below a problem that I am stuck with for 4-5 days now. Could you please go through it and give suggestions or lead...

Hello experts, I am listing below a problem that I am stuck with for 4-5 days now. Could you please go through it and give suggestions or lead me to someone in your contact list who might have experience in related issues? Our target board is based on the DM640 and we have designed its JTAG circuitry exactly as in the DM642 EVM. We are using the 14- pin JTAG connector connected to a XDS5...

Our company has a DSP board based the C67x DSP. I did the work on the Software about a year ago. We are now starting up a new project to augment...

Our company has a DSP board based the C67x DSP. I did the work on the Software about a year ago. We are now starting up a new project to augment the functionality of the software. When I did the original work we used a modified DSK to talk to our board. It was never extremely reliable, one only have one, and the guy who did the modifications has moved on. We are now looking at buying a JTag e...

Hi In bringing up a dsp TI320C6201 board with 32 MByte SDRAM MT48LC4M16A2(8 MByte each) on board I am facing some problems. ...

Hi In bringing up a dsp TI320C6201 board with 32 MByte SDRAM MT48LC4M16A2(8 MByte each) on board I am facing some problems. First of all when I power up the board I used spectrum digital XDS510PP to dump my code on chip through Jtag. I used internal memory map BOO

Hi everybody, Did anyone experienced connection problems with CCS 3.0? My board is a third party board from Innovative...

Hi everybody, Did anyone experienced connection problems with CCS 3.0? My board is a third party board from Innovative Integration (Toro), including the C6711 dsp. I use the xds510pp-plus JTAG. Actually, I can connect the emulator to the board with

Hi,everyone. I am debugging a board with 4 C6701 in a JTAG chain. Some days ago,I could get into the CCS and access the onboard...

Hi,everyone. I am debugging a board with 4 C6701 in a JTAG chain. Some days ago,I could get into the CCS and access the onboard resources. Later,I couldn't bring up the CCS when the CPU2 is in the JTAG chain. So I have to BYPASS it in the CCS Setup to go on my debugging and in the

Hi Calvin, I would like to have some help from your side. I am using USB JTAG for debugging the board having TI6415 processors. ...

Hi Calvin, I would like to have some help from your side. I am using USB JTAG for debugging the board having TI6415 processors. But the JTAG is from company called Signum. When i start the CCS 2.2 i am getting the following error. "Error Code : 0x80000240/-180, This was ge

hi i have a 6201 BGA device connected wih lot of problems to the pcb.now i want to check if all of its pins  realy connected or...

hi i have a 6201 BGA device connected wih lot of problems to the pcb.now i want to check if all of its pins  realy connected or not, i have an XDS510 jtag emulator and i heard that it is possible to check the pins with that, do i need a special soft ware or code composer can do it for me?

Hi all, I?m trying load a COFF file (.out) since PC using hpi, but an error in Code Composer Studio is showed. The error is...

Hi all, I?m trying load a COFF file (.out) since PC using hpi, but an error in Code Composer Studio is showed. The error is "JTAG Communication error". To load the COFF file I?m using 'dsk6xldr' application provided by dsk 2.0 in 'C:\ti\examples\dsk6711\board_u

Hi everybody, I am new to dsp. I just received an XDS510 USB JTAG Emulator. I also have a Valde Systems VS1501 Board, which is based on the...

Hi everybody, I am new to dsp. I just received an XDS510 USB JTAG Emulator. I also have a Valde Systems VS1501 Board, which is based on the TMS320DM642 Processor. I installed the XDS drivers and went to CCSv3.3 Setup to Configure the board. I used the following configuration: C64xx Rev 1.1 XDS510-USB Board Driver Location: C:\CCStudio_v3.3\drivers\sdgo6400usb_11.dvr Diagnostic Utilit...

Peter- > Anyone have any tips on production testing techniques for pc boards > using the C64xx BGA chip? Several years ago my company...

Peter- > Anyone have any tips on production testing techniques for pc boards > using the C64xx BGA chip? Several years ago my company used to make DSP module functional test systems for Sanmina Viking-InterWorks... here are a few comments. I apologize in advance if my comments are redundant with Mike Dunn's. > i.e. is Xray inspection of the BGA contacts standard? No. Only if a nu

Hi all, i have 3 questions about the way target transfer data to host. First im want to know how to send floating point data to matlab and...

Hi all, i have 3 questions about the way target transfer data to host. First im want to know how to send floating point data to matlab and also how to recive data in the tms320c6713 target using matlab.I was trying to run some example of CCS where send any kind of data but always send integer data, i only can´t send this kind of data? Second how can i use the jtag interface to send data...

Yes Michael, Now my board is connecting, via JTAG, using the Gao xds510. I was pulldown (by wrong) a EMU pin. I read the SPRA584C Application...

Yes Michael, Now my board is connecting, via JTAG, using the Gao xds510. I was pulldown (by wrong) a EMU pin. I read the SPRA584C Application Report (TI) and revises may design. Thanks. Ricardo ________________________________ De: Michael Dunn [mailto:m...@gmail.com] Enviada: qua 31/10/2007 16:29 Para: Ricardo Jose de Oliveira Carvalho Cc: c...@yahoogroups.com Assunto: Re: [c6x] Er...