Hi, Perhaps this should be a question for TI support... but anyway, I'd appreciated if anyone in the group has experience with...

Hi, Perhaps this should be a question for TI support... but anyway, I'd appreciated if anyone in the group has experience with this. I have a board with some c6203's on it (just one of them in the JTAG chain), but can not get the RTDX diagnostic tests in CCS v2.0 to wor

I'm using c6701 based TI DSP board with JTAG and CCS ver2.0. I'm implementing FX-LMS algortihm;  to do real time debugging I'm...

I'm using c6701 based TI DSP board with JTAG and CCS ver2.0. I'm implementing FX-LMS algortihm;  to do real time debugging I'm trying to use DSP bios, however, I could not make my program run. I compil

Hi, Iam having few installation issues with my TMS320C6701 EVM board. The Board is a PCI slot card which goes into the mother...

Hi, Iam having few installation issues with my TMS320C6701 EVM board. The Board is a PCI slot card which goes into the mother board pci slot with an embedded jtag and not an external one. the issue is that,while the evm board is recognised and installed under emulation in devic

JTAG emulator enables high-speed RTDX? data link at more than two megabytes per second and code download speeds at up to half a ...

JTAG emulator enables high-speed RTDX? data link at more than two megabytes per second and code download speeds at up to half a megabyte per second For more info: http://www.dspvillage.ti.com/emulator8 HOUSTON

freinds we are using TMS320C6211 dsp custom board, and we are feeding programs through JTAG thru XDAS510PP,while working with...

freinds we are using TMS320C6211 dsp custom board, and we are feeding programs through JTAG thru XDAS510PP,while working with CCS its giving some time Little Endian and some time Big Endianmode of operation ,though the dsp has been designed to work under Little Endian Mode by

I have developed the 6701 system as follow: - enable to execute the user code in internal memory using JTAG - when the specific...

I have developed the 6701 system as follow: - enable to execute the user code in internal memory using JTAG - when the specific code is in boot ROM, enable to download the user code through RS232 or USB to SDRAM - when the user code is downloaded, enable to execute that code v

Hi all, How to profile a c-function in the emulation mode?? I am connected to a custom board thro'h Parallel Jtag emulator. ...

Hi all, How to profile a c-function in the emulation mode?? I am connected to a custom board thro'h Parallel Jtag emulator. In DSP/BIOS user's guide, under STS module it is given that how to use it for profiling. I covered my function to be profiled between STS_set

Hi everybody, We made a board with a 6211 dsp. To debug it we use the XDS510PP emulator via JTAG. As a testbed, we used a 6711...

Hi everybody, We made a board with a 6211 dsp. To debug it we use the XDS510PP emulator via JTAG. As a testbed, we used a 6711 dsk. To program the rom on the dsk, ti provides a flash programming utility which downloads the hex file to the rom. Unfortunately it works only with t

Hi, I'm trying to build the video system with framegraber and TI EVM board (C55 or C62). The framegraber must be on the PC PCI...

Hi, I'm trying to build the video system with framegraber and TI EVM board (C55 or C62). The framegraber must be on the PC PCI port and interface to EVM via serial port (McBsp). The debugging of DSP will bi via ISA JTAG. The question is how to interface between fra

Dear c6x: when I run the CCS, it always report "initial CUP error! Detect Reg error!" Someone know what is problem on it? Thanks...

Dear c6x: when I run the CCS, it always report "initial CUP error! Detect Reg error!" Someone know what is problem on it? Thanks a lot. Best Regards Jun.Zhou 2002-12-20

dear all, i am now using tms320c6711 dsk board in my student project. i use spp mode to communicate the paralled port to my...

dear all, i am now using tms320c6711 dsk board in my student project. i use spp mode to communicate the paralled port to my pc printer port. it can not initialize the target cpu when i start to use ccs. error-1101 stated that check the target power and jtag

Following was the problem noticed with the DSK: C6711 DSK - After connecting it with DB15 connector when i try to run code...

Following was the problem noticed with the DSK: C6711 DSK - After connecting it with DB15 connector when i try to run code composer in DSK mode, it does not pop up and report the error as 'can't initialize the target'. But if i plug in the emulator cable on the Jtag of

Hi, I am presently developing under Code Composer (CCS) v2.2. I can compile, load and execute my code under Code Composer via...

Hi, I am presently developing under Code Composer (CCS) v2.2. I can compile, load and execute my code under Code Composer via the JTAG. What options do I need to include for my compiled code so that it boots and runs correctly when the ".out" file is download

Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate...

Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate jumper settings on the board, which gives the video output and LEDs ON as described on the installation guide. (meaning the hardware is connected

Hi, I am building a program which captures data from the PCM3003 audio card, by means of HWIs, and sends it to a PC, via JTAG,...

Hi, I am building a program which captures data from the PCM3003 audio card, by means of HWIs, and sends it to a PC, via JTAG, when 512 samples are available. I am using the TMSC6711 DSP. Do the HWI interfere with the RTDX? When I try to use interrupt- driven RTDX

Hi, I am trying to install the EVM 6201 in a PC (over Win95 and Win98 ). I tested in onboard and offboard motherboard PC but...

Hi, I am trying to install the EVM 6201 in a PC (over Win95 and Win98 ). I tested in onboard and offboard motherboard PC but experiment the same error message for all combinations PC - OS: CAN'T INITIALIZE THE TARGET CPU CAN'T INITIALIZE THE JTAG CONTROLLER PLEASE ENSURE

hello everyone. I have designed a board with 2 C6711B150. But when i startup ccs, it says it can not initialize CPU.Sometimes it...

hello everyone. I have designed a board with 2 C6711B150. But when i startup ccs, it says it can not initialize CPU.Sometimes it can not initialize CPU_2, sometimes it can not initialize CPU_1, and sometime it can not initialize both. My schematic is JTAG.SCH. Bootmode =

I have designed a board around TI's C6711. I am trying to perform emulation under CCS 2.20 using the spectrum's XDS510PP emulation...

I have designed a board around TI's C6711. I am trying to perform emulation under CCS 2.20 using the spectrum's XDS510PP emulation POD. The "SDConfig" finds and passes the Jtag chain with results like: ** Emulator Test ** $$ EmuProductName=XDS510PP $$ Emu

Hi, I have some question about Interface DSK6711 to PC. As I know there are only two ways to interface DSK6711 to PC, One is LPT1 ...

Hi, I have some question about Interface DSK6711 to PC. As I know there are only two ways to interface DSK6711 to PC, One is LPT1 using EPP mode and the other is JTAG which could use XDS510 or XDS560. I have problem that I want to send image frame(640x480) from DSK6711 t

hello !  i got a big problem when emulating my own board. this is my emulating evironment:               CCS2.2 ...

hello !  i got a big problem when emulating my own board. this is my emulating evironment:               CCS2.2        PCI emulator card with JTAG      &nb