DSPRelated.com

[Fwd: Re: [Fwd: Re: can't connect to target after flashburn]]

Started by Jeff Brower in TMS320c6x20 years ago 1 reply

Mike- That's some pretty strong evidence that the JTAG state machine is susceptible to undefined op codes -- maybe that...

Mike- That's some pretty strong evidence that the JTAG state machine is susceptible to undefined op codes -- maybe that situation is harder to deal with for a VLIW device? Another possibility is that the code appears to act normally, but jumps to location ze


ccs can not initialize CPU

Started by Chen Cerdar in TMS320c6x21 years ago 2 replies

hello everyone. I have designed a board with 2 C6711B150. But when i startup ccs, it says it can not initialize CPU.Sometimes it...

hello everyone. I have designed a board with 2 C6711B150. But when i startup ccs, it says it can not initialize CPU.Sometimes it can not initialize CPU_2, sometimes it can not initialize CPU_1, and sometime it can not initialize both. My schematic is JTAG.SCH. Bootmode =


_RTDX interrupt mask error

Started by stuckat7 in TMS320c6x16 years ago

Hi, I am trying to send data to DSK6713 through JTAG and have tried to run many examples....even the ones in the help tutorials. But I...

Hi, I am trying to send data to DSK6713 through JTAG and have tried to run many examples....even the ones in the help tutorials. But I keep on getting the same error msg _RTDX_interrupt_mask C:/CCStudio_v3.1/C6000/rtdx/lib/rtdx.lib > > error: symbol referencing errors - './Debug/RTDX_MATLAB_sim.out' not built I would be be grateful for ny sorta help. Check Out I


MSP430 not recognized by emulator

Started by ahme...@yahoo.com in TMS320c6x14 years ago 2 replies

Hello all, I hv a Lyrtech DM648EVM which has on board MSP430 with a JTAG support for programming. I hv recently purchased TI...

Hello all, I hv a Lyrtech DM648EVM which has on board MSP430 with a JTAG support for programming. I hv recently purchased TI MSP-FET430UIF (USB) programmer for it with the IAR kick start(EWB). The problem is, on board MSP430 controller is not recognised by Emulator although I have followed all the instructions. Is there any other HW/SW needed (in addition to one I hv)to Program on...


giving data from the TMS320C6414 to matlab as input

Started by avam...@yahoo.com in TMS320c6x19 years ago

Can any one please guide me how to input data to a MATLAB file, the data supposed to come from the processor acquiring real time data, I...

Can any one please guide me how to input data to a MATLAB file, the data supposed to come from the processor acquiring real time data, I think i need to pass it from code composer to MATLAB via JTAG. but i am not knowing the exact procedure. Thanks in advance


I2C module of ATEME's IEKLIB

Started by Anand K in TMS320c6x21 years ago

Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate...

Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate jumper settings on the board, which gives the video output and LEDs ON as described on the installation guide. (meaning the hardware is connected


download boot code to rom

Started by fedelegger in TMS320c6x21 years ago 1 reply

Hi everybody, We made a board with a 6211 dsp. To debug it we use the XDS510PP emulator via JTAG. As a testbed, we used a 6711...

Hi everybody, We made a board with a 6211 dsp. To debug it we use the XDS510PP emulator via JTAG. As a testbed, we used a 6711 dsk. To program the rom on the dsk, ti provides a flash programming utility which downloads the hex file to the rom. Unfortunately it works only with t


Neeeeeed help

Started by Anonymous in TMS320c6x19 years ago 2 replies

Hi, I have a problem in ports and JTAG communication error displaying. The DSK was ok and I don\'t Know what is happen (may be...

Hi, I have a problem in ports and JTAG communication error displaying. The DSK was ok and I don\'t Know what is happen (may be due to executes random code), and the user LEDs in C6711 DSK remain on when DSK is powered until open CCS, after that LED flashed and switched off. Actually I spent mor


flashing + booting on 6414 custom target

Started by soma_64x in TMS320c6x20 years ago

hi, i have a couple of question on boot application development for custom target I have a target which uses 6414DSP. with...

hi, i have a couple of question on boot application development for custom target I have a target which uses 6414DSP. with 256kb flash on emifb and 8MB SDRAM on emifa with CCS2.2 with JTAG interface to burn the code. I need a clairification on my approach.


JTAG issue

Started by jsau...@gmail.com in TMS320c6x15 years ago 2 replies

I am using TMS320c6713B custom board along with Spectrum Digital EMulator xds510usb. While Connecting with my custom board using sdconfig utility...

I am using TMS320c6713B custom board along with Spectrum Digital EMulator xds510usb. While Connecting with my custom board using sdconfig utility I got ok results. It can scan pattern and verfiy patterns also . However when i start CCS studio i found a message " An unknown error prevented the Emulator in a timely fashion. " I have checked with Reset also . It seems fine too. I am using TPS70345 a...


Unexplained halt in CCS with XDS510 USB Plus JTAG and TMS320C6713B DSP

Started by kernelbloat in TMS320c6x15 years ago 4 replies

Hello, I'm working on a project for which we have designed a custom board with a TMS320C6713B DSP. We are having some problems with the DSP...

Hello, I'm working on a project for which we have designed a custom board with a TMS320C6713B DSP. We are having some problems with the DSP chip, for which we have not yet tracked down the cause. Code which should be executing fine on the DSP is "blowing up" (PC is getting derailed). We suspect some issue with SDRAM, though my memory tests through the HPI port (from a host CPU) seem to check...


Endian problem

Started by raja nayaka in TMS320c6x22 years ago 1 reply

freinds we are using TMS320C6211 dsp custom board, and we are feeding programs through JTAG thru XDAS510PP,while working with...

freinds we are using TMS320C6211 dsp custom board, and we are feeding programs through JTAG thru XDAS510PP,while working with CCS its giving some time Little Endian and some time Big Endianmode of operation ,though the dsp has been designed to work under Little Endian Mode by


Boot problem

Started by gangadhar80reddy in TMS320c6x19 years ago 4 replies

We need to load an application to DSP memory and, boot and run the application on the DSP board without using JTAG through...

We need to load an application to DSP memory and, boot and run the application on the DSP board without using JTAG through our Test application We are working with TMS 320C6415 The DSP application is created using CCS. This small project has the c


Target Type Matching Problem

Started by jalal_habibi in TMS320c6x19 years ago 1 reply

Hi all, I have a problem with XDS510 USB JTAG emulator that has been connected to my DSP hardware. I use TMS320c6713PYP....

Hi all, I have a problem with XDS510 USB JTAG emulator that has been connected to my DSP hardware. I use TMS320c6713PYP. The CCS could not load the .out file to DSP memory. I've get the following message: "... not loaded. Does not match the target type...&q


jam player for Altera Cyclon on C6205

Started by maozlo in TMS320c6x20 years ago 3 replies

Hi All, I am trying to configure an Altera chip (Cyclon) through the JTAG interface. I need to configure it with a jam...

Hi All, I am trying to configure an Altera chip (Cyclon) through the JTAG interface. I need to configure it with a jam player. Has anyone ported the code for this to C6000? Do you know where I can find something like that? Thanks, Maoz Loants


PLL Control/Status Register

Started by vbehravan in TMS320c6x19 years ago 1 reply

Hi all, We develop a TMS320C6713 board. The C6713 code has been tested using XDS510usb JTAG emulator and everything is O.K....

Hi all, We develop a TMS320C6713 board. The C6713 code has been tested using XDS510usb JTAG emulator and everything is O.K. To finalize our system, we switch to HPI boot loading and load the C6713 code using HPI. In the preliminary stages of our code, we


Profiling in Emulation mode??

Started by simha j in TMS320c6x21 years ago

Hi all, How to profile a c-function in the emulation mode?? I am connected to a custom board thro'h Parallel Jtag emulator. ...

Hi all, How to profile a c-function in the emulation mode?? I am connected to a custom board thro'h Parallel Jtag emulator. In DSP/BIOS user's guide, under STS module it is given that how to use it for profiling. I covered my function to be profiled between STS_set


breakpoint error

Started by mayank agarwal in TMS320c6x19 years ago 2 replies

Hi all, I am fed up seeing this error whenever i load the program.I am using DM642 emulator board.Please suggest something so that i can...

Hi all, I am fed up seeing this error whenever i load the program.I am using DM642 emulator board.Please suggest something so that i can be able to remove this error. Are there changes in memory map,JTAG settings,etc Can't Set Breakpoint: Error 0x00000008/-1076 Error during: Break Point, Cannot set/verify breakpoint at 0x807EB518 Breakpoint Mana


DSK6414 Interface to PC

Started by Henrry Andrian in TMS320c6x20 years ago 1 reply

Dear all, I would like to ask question about DSK6416 interface to PC. In DSK6711, I could using HPI via LPT1 interface to...

Dear all, I would like to ask question about DSK6416 interface to PC. In DSK6711, I could using HPI via LPT1 interface to connect to PC. Since the DSK6416 didnt have any LPT1 interface, I cant use LPT1 interface. But I saw that DSK6416 have USB-JTAG emulation. So I would


Problems using the statistic object of the DSP/BIOS

Started by jari...@indra.es in TMS320c6x18 years ago

Hi All, I am debuging my real time application by using a JTAG emulator and CCS 2.2 on my custom board based on the C6416. My application...

Hi All, I am debuging my real time application by using a JTAG emulator and CCS 2.2 on my custom board based on the C6416. My application consist of an outer infinite loop that waits for data from another module to begin processing, and so i first collect data on target and finally call IDL_run to fetch it to host. What have tried so far is the following is the typical setup to measure perform...