DSPRelated.com

C6711B emulation/startup help

Started by Sijia LI in TMS320c6x21 years ago 3 replies

Hi, SOS on followed problem, thanks lot in advance! I am using TMS320C6711B with XDS560 emulator. The problem now is the CCS 2.10...

Hi, SOS on followed problem, thanks lot in advance! I am using TMS320C6711B with XDS560 emulator. The problem now is the CCS 2.10 can't start up,the error message is: Can't initialize the target CPU: 1. Target initialize failed <-1200> 2. Check


I2C module of ATEME's IEKLIB

Started by Anand K in TMS320c6x21 years ago

Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate...

Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate jumper settings on the board, which gives the video output and LEDs ON as described on the installation guide. (meaning the hardware is connected


Problem with IT

Started by Mich...@zenitel.biz in TMS320c6x18 years ago

Hi, I work with the TMS320C6711 using CCS2 and a Blackhawk XDS560 USB Emulator. My application is loaded on a SRAM at adress 0x80000000...

Hi, I work with the TMS320C6711 using CCS2 and a Blackhawk XDS560 USB Emulator. My application is loaded on a SRAM at adress 0x80000000 using a second level bootloader. A timer IT (IT14 - Timer 0) is programmed to be executed every 10ms. The interrupt routine adress is in the SRAM plage adress. When I initialize the ISTP base adress at location 0x400, the


6711D memory load

Started by rjed...@gmail.com in TMS320c6x14 years ago 14 replies

hi we have developed an audio application based around the c6711 D dsp. We are using the XDS560 emulator and ccs 2.1. We can successfully...

hi we have developed an audio application based around the c6711 D dsp. We are using the XDS560 emulator and ccs 2.1. We can successfully load the program onto the audio device through load program on ccs. and when loaded the cursor appears at c_int00. But when the program is run it just goes to a series of nops. When we look at the our c code and and asm generated under the view-> mixed as


Device driver needed for xds560 JTAG Emulator

Started by Tahir Mehmood in TMS320c6x16 years ago

Dear All, I am currently working on Black Hawk XDS 560 JTAG Emulator. I recieve error messages while setting up Code Composer Studio (Version...

Dear All, I am currently working on Black Hawk XDS 560 JTAG Emulator. I recieve error messages while setting up Code Composer Studio (Version 2.2 or 3.1 ) that the device driver file (tixds560c6x.dvr )does not exist. I have tried to find it out on blackhawk website and ti.com but there is no such file available there.Please if any one knows where to get this file or someone has this file plea...


RTDX problem

Started by Beh CS :-|| in TMS320c6x21 years ago 9 replies

Hi, I'm using TI's C6415 processor, C6400 xds560 board and CCS 2. When I try the RTDX tutorials, I can't enable the RTDX...

Hi, I'm using TI's C6415 processor, C6400 xds560 board and CCS 2. When I try the RTDX tutorials, I can't enable the RTDX function in CCS. I got the message : "GTI device driver failed to enable RTDX" Has anyone face the similiar problem ? What sho


emulator + dsk

Started by sord...@hotmail.com in TMS320c6x18 years ago

Hi to all, I am going to post a question that may sound stupid, but I haven't been able to find out the answer. I have...

Hi to all, I am going to post a question that may sound stupid, but I haven't been able to find out the answer. I have configured correctly my dsk6713 and it works. I also have an XDS560 POD that is correctly connected to the PC. The question is: Is always necessary that the POD cable is connected to the DSK by the JTAG port?? Can the emulator works without this conection...


Re: Device driver needed for xds560 JTAG Emulator

Started by Michael Dunn in TMS320c6x16 years ago

Tahir, On 10/19/07, Tahir Mehmood wrote: > > Dear All, > I am currently working on Black Hawk XDS 560 JTAG Emulator. I recieve error...

Tahir, On 10/19/07, Tahir Mehmood wrote: > > Dear All, > I am currently working on Black Hawk XDS 560 JTAG Emulator. I recieve error messages while setting up Code Composer Studio (Version 2.2 or 3.1 ) that the device driver file (tixds560c6x.dvr )does not exist. I have tried to find it out on blackhawk website and ti.com but there is no such file available there.Please if a


Booting problem of C6416T custom board

Started by shad...@yahoo.com in TMS320c6x16 years ago 2 replies

Hi. I've made a custom board using TMS320C6416T. Boot mode is host boot and the board has no HPI or PCI. When I connected the target...

Hi. I've made a custom board using TMS320C6416T. Boot mode is host boot and the board has no HPI or PCI. When I connected the target board to the CCS with XDS560 JTAG emulator, the following error message showed up: ------------------------------------------------------------------- Error connecting to the target: Error 0x80000240/-1147 Fatal Error during: Initialization, OCS, I...


TMS320C6203 cannot boot correctly

Started by mike...@yahoo.com.cn in TMS320c6x14 years ago 2 replies

Hi everyone, Now I have a problem about TMS320C6203 boot in my project. We design a C6203 DSP system, with a fifo connecting to the DSP and...

Hi everyone, Now I have a problem about TMS320C6203 boot in my project. We design a C6203 DSP system, with a fifo connecting to the DSP and the external interface by XBUS.Sometiems TMS320C6203 cannot boot correctly.Power on 20 times,one time TMS320C6203 cannot boot . when not boot,I connected the target board to the CCS with XDS560 JTAG emulator.Flash data read by CCS all are 0XFF.I have a re...


(spectrum digital ) xds560r or xds510 for divinci tms320dm6446?

Started by Khawar Shahzad in TMS320c6x15 years ago 2 replies

Hi, I will have to work on a custom board with davinci tms320dm6446 processor on it. I am a bit confused regarding the emulators which i will...

Hi, I will have to work on a custom board with davinci tms320dm6446 processor on it. I am a bit confused regarding the emulators which i will have to use. My questions are following : 1) Will i need an emulator (spectrum digital, 20 pin cti, xds510 or xds560) for downloading my code for the processor and also for burning the flash? I am a bit confused that are these emulators ( xds56...


Failed Software Reset: Error 0x00000028/-1076

Started by z_11...@yahoo.com in TMS320c6x15 years ago 2 replies

In a new design with C6713, connecting to CCS is successful, Oscillator and capacitors, some required resistor and EMI filter and buffer of...

In a new design with C6713, connecting to CCS is successful, Oscillator and capacitors, some required resistor and EMI filter and buffer of emulator assembled on board due to test and debug be easier. No external flash or SDRAM assembled and emulator is xds560. during a simple program, when loading .cinit to 0x2960 one error occurred:? data verification failed at 0x2960 please verify targ


the problem of TMS320C6203 boot

Started by mike...@yahoo.com.cn in TMS320c6x14 years ago

Dear All, Now I have a problem about TMS320C6203 boot in my project. We design a C6203 DSP system, with a fifo connecting to the DSP and the...

Dear All, Now I have a problem about TMS320C6203 boot in my project. We design a C6203 DSP system, with a fifo connecting to the DSP and the external interface by XBUS.Sometiems TMS320C6203 cannot boot correctly.Power on 20 times,one time TMS320C6203 cannot boot . when not boot,I connected the target board to the CCS with XDS560 JTAG emulator.Flash data read by CCS all are 0XFF.I have a reset...


Emulator

Started by swapnali patil in TMS320c6x19 years ago 2 replies

HI! All Can any 1 tell what is diff between  510 & 560 emulators both are suggested for DM64X family then what is diff. 2. We have 1...

HI! All Can any 1 tell what is diff between  510 & 560 emulators both are suggested for DM64X family then what is diff. 2. We have 1 licenced version of CCS with Emulator XDS560, can this CCS can be  loaded on other PC which is not having h/w Emulator, will work as simulator. is there any s/w is required   pls help for this


Reg:JTAG Debug Problem

Started by venkat arvapalli in TMS320c6x17 years ago 4 replies

Hi All, I am using XDS560 PCI emulator inorder to debug the DSP code running on DM642. By using Parallel Debug Manager I was able to connect...

Hi All, I am using XDS560 PCI emulator inorder to debug the DSP code running on DM642. By using Parallel Debug Manager I was able to connect the DSP Board which consists of four DM642's and after that i was able to load my DSP.out file into each DM642 Processor. But While running the dsp code i am facing the following error Error: Error 0x00000022/-1154 Error during: Memory, Execution, ...


CCS 3.1 Emulator problems

Started by danikenig in TMS320c6x18 years ago

Hi, I am trying to migrate to CCS 3.1 from 2.2. I have been using GEL files for unit testing my different libraries and it's been very...

Hi, I am trying to migrate to CCS 3.1 from 2.2. I have been using GEL files for unit testing my different libraries and it's been very stable with CCS 2.2, however I have problems using the same emulator (TI XDS560) with CCS 3.1. The emulator seems to lose connection with the target from time to time while loading / running my program, loading files etc. I did change the GEL files as ...


DM6446 debug ARM

Started by wang...@126.com in TMS320c6x15 years ago 1 reply

I am using DM6446 and xds560 emulator. Can I use ARM's assemble language to debug ARM in CCS?? I write a simple program in CCS ...

I am using DM6446 and xds560 emulator. Can I use ARM's assemble language to debug ARM in CCS?? I write a simple program in CCS using ARM's assemble language. But when compile it , I get mang errors in the output window of CCS. I just want to use ARM's assemble language to read and write ARM's register. Is there some document I can refer to?? _______...