Does the VxWorks can run on the ADSP-TS201?

Started by darkbluelilas in comp.dsp16 years ago 4 replies

hello, Does anybody know if the VxWorks can support the ADSP-TS201 chip of ADI? Thanks.

hello, Does anybody know if the VxWorks can support the ADSP-TS201 chip of ADI? Thanks.


HELP with ADSP-21161 Ez-Kit !!!

Started by Flavia in comp.dsp17 years ago 3 replies

Hi! Have someone programier a fir filter for this ADSP-21161 EZ-Kit and for 96kHz sample rate? I am new in the DSP world. Have someone...

Hi! Have someone programier a fir filter for this ADSP-21161 EZ-Kit and for 96kHz sample rate? I am new in the DSP world. Have someone worked with the ADSP-21161 EZ-Kit? I need to program a correlation. That?s mean a matched filter, als a fir filter? I need 96kHz sample rate for the AD. That?s mean I2S mode but there is not a lot of examples for I2S mode configuration. I need Help!...


ADSP-14060 Board?

Started by Al Clark in comp.dsp10 years ago

I am potentially working on an existing product that uses an ADI ADSP-14060 (Quad SHARC). My task is strictly software. I might like to...

I am potentially working on an existing product that uses an ADI ADSP-14060 (Quad SHARC). My task is strictly software. I might like to buy a working board that includes this processor and a JTAG connection. Does anyone have something that might work? Al Clark Danville Signal


ADSP-21262 ROM?

Started by Leon in comp.dsp15 years ago 9 replies

I've just got a couple of samples of the new ADSP-21262 SHARC DSP (1200 MFLOPS!) in the LQFP package. It is a masked-ROM device, and I...

I've just got a couple of samples of the new ADSP-21262 SHARC DSP (1200 MFLOPS!) in the LQFP package. It is a masked-ROM device, and I wondered if there was likely to be anything useful in the ROM. I've started designing a simple PCB so that I can play with them, it'll consist basically of the '21626 and a suitable codec. Leon


ADSP-21xx SPORT

Started by Vladimir Vassilevsky in comp.dsp18 years ago 6 replies

Hello All, According to the datasheet, the SPORT of ADSP-21xx is double buffered. There is a need to transmit just two serial words in one...

Hello All, According to the datasheet, the SPORT of ADSP-21xx is double buffered. There is a need to transmit just two serial words in one burst. Is it possible to write two words one immediately after other to TX register? Vladimir Vassilevsky DSP and Mixed Signal Design Consultant http://www.abvolt.com


GNU TOOL Chain for ADSP

Started by ratemonotonic in comp.dsp14 years ago

Hi all , I am just getting started on a project using ADSP-21XX , is there a GNU tool chain for it ? There are GNU toolchain for Blackfin...

Hi all , I am just getting started on a project using ADSP-21XX , is there a GNU tool chain for it ? There are GNU toolchain for Blackfin processors , How dependable are they ? As I have an opportunity to choose the DSP for our new hardware platform. Thanks in advance Rate


ADSP 21160 questions on example

Started by Marc Finet in comp.dsp18 years ago 4 replies

I'm a newbie on DSP, so I got this example on the analog...

I'm a newbie on DSP, so I got this example on the analog site (ftp://ftp.analog.com/pub/dsp/2116x/examples/simd_single_channel/adsp-2116x_vector_maximum.zip): /* [...] Description: Subroutine that records the value and location of the maximum value in a given (real) vector. Equation: MAX_VAL = MAX[INPUT] MAX_INDEX


ADSP-212xxx: Problem with VisualDSP++ 4.0

Started by rob.hutchins in comp.dsp16 years ago 6 replies

Hello list, First off: I apologize if this is not a list to which I should post questions about the ADSP-212xx EZ-KIT lite and its IDDE -...

Hello list, First off: I apologize if this is not a list to which I should post questions about the ADSP-212xx EZ-KIT lite and its IDDE - VisualDSP++. I couldn't find an active Analog Devices related board and this seemed to be the place I could get help at. I had to uninstall VisualDSP++ 3.5 this morning as it would not open a debug session, and I installed VisualDSP++ 4.0 which I down...


ADSP-2189M wizard programmer needed

Started by Me in comp.dsp15 years ago 1 reply

For a very interesting DSP project, we are looking for wizard programmers for Analog Devices, ADSP-2189M DSP Microcomputer. Please leave your...

For a very interesting DSP project, we are looking for wizard programmers for Analog Devices, ADSP-2189M DSP Microcomputer. Please leave your contacts at the newsgroup or email your resume and availability ASAP to DRDSP at hotmail dot com . (Preference to California located people.)


ADSP 21161N ez_kite_lite, english

Started by chris_08 in comp.dsp16 years ago 1 reply

Hello! I am a student of the TGM a technical college in Vienna. I use the ADSP 21161N_ez_kite_lite board with a SHARC processor. I need...

Hello! I am a student of the TGM a technical college in Vienna. I use the ADSP 21161N_ez_kite_lite board with a SHARC processor. I need help because I want to receive some signals (HIGH/LOW) from an external board which is connected to a port from the DSP. The signals will be used by the application. I have problems to address each bus-line from the port separate. I tried this by the ...


ADSP-2116x PC register format

Started by marc-f in comp.dsp18 years ago 1 reply

Hello, I'm working on the ADSP-21160, and I wanted to know what is the format of the PC register. In the Hardware Reference (2nd ed), page...

Hello, I'm working on the ADSP-21160, and I wanted to know what is the format of the PC register. In the Hardware Reference (2nd ed), page A-36, it is written that DM/PM addresses buses have the following format : |31 23|22 20|19 17|16 0| | E Field | M field | S field | address | But the sequencer uses 24 bit addres...


SHARC ADSP-21375

Started by rkn80 in comp.dsp13 years ago 1 reply

HI, I'm using the ADSP-21375 SHARC. Does anybody know how I can write data to external data bus without using the AMI or the SDRAM...

HI, I'm using the ADSP-21375 SHARC. Does anybody know how I can write data to external data bus without using the AMI or the SDRAM controller? The reasoan is that I want to do the cycle delays etc. by myself so simply lets say I want to write the value 0x9090 to D0-D15 and these values shoul remain there as long as I want. Raphael


matrix inverstion on ADSP TS101s

Started by caterpiller in comp.dsp15 years ago 1 reply

hi, there, I am trying to look for a good algorithm for matrix inversion on ADSP ts101s. It is better be the assembler language version. I...

hi, there, I am trying to look for a good algorithm for matrix inversion on ADSP ts101s. It is better be the assembler language version. I have tried the C function matinvf() from Analog device library, It costs me 1.62ms for a 32*32 float matrix. This time is not I want. I hope the computation should be about 100 microseconds. Does anybody know if the C library on VisualDSP++ is optimi...


ADSP 218x AV bit

Started by Ephreal in comp.dsp10 years ago 1 reply

Hi I'm corrently playing around with an 2183 ADSP, and writing some test programs for it. However I fail to understand the logic behind the AV...

Hi I'm corrently playing around with an 2183 ADSP, and writing some test programs for it. However I fail to understand the logic behind the AV bit in the astat register. I have to user guide, and I've read and understand the principle of it however I would like a more indepth knowledge. Can anyone here explain how it works, and/or have som examples how to test the bit. Thank you /Eph...


ADSP-21469

Started by stevenceuppens in comp.dsp6 years ago 2 replies

Hi all, I ordered a evaluation board of the ADSP-21469, which i want to use for learning & exploring sharc programming (Assembly, C, C++). I...

Hi all, I ordered a evaluation board of the ADSP-21469, which i want to use for learning & exploring sharc programming (Assembly, C, C++). I never used a sharc processor before, but i'm expierienced in programming ARM, STM32, ... What is the best way to learn sharc programming, and where can i find usefull help, tutorials etc... I already found lots of info on the analog devices website, but...


AD Support for the ADSP 210XX line of DSPs

Started by Steve Holle in comp.dsp18 years ago 2 replies

Just for general information, I found out today that AD is no longer offering telephone support for any of the ADSP 210XX line of DSPs. The...

Just for general information, I found out today that AD is no longer offering telephone support for any of the ADSP 210XX line of DSPs. The only way to get support is via email. You might want to consider this when choosing a DSP for your next project. Let the buyer beware.


TalkThrough ADSP BF533

Started by SDV in comp.dsp15 years ago 2 replies

Hi, I'm programming an ADSP-BF533 EZ-KIT Board for audio signal processing. In main file of "Talkthrough" (by Analog Device) there's the...

Hi, I'm programming an ADSP-BF533 EZ-KIT Board for audio signal processing. In main file of "Talkthrough" (by Analog Device) there's the following declaration: // array for registers to configure the ad1836 // names are defined in "Talkthrough.h" volatile short sCodec1836TxRegs[CODEC_1836_REGS_LENGTH] = { DAC_CONTROL_1 | 0x000, DAC_CONTROL_2 | 0x000, DAC_VOLUME_0 | 0...


ADSP-21364 Beginners Guide

Started by omal...@gmail.com in comp.dsp16 years ago 6 replies

I have written some Matlab code and am trying to embed it on an Analog Devices adsp-21364 processor. This is my first time using a dsp and I'm...

I have written some Matlab code and am trying to embed it on an Analog Devices adsp-21364 processor. This is my first time using a dsp and I'm having alot of trouble getting started, big lack of documentation on the basics. I am willing to re-write the matlab code in C or assembly. Could anybody supply a link to some good relevant documentation Thanks very much


ADSP-BF-518BSWZ-4F Blackfin processor

Started by Tiffanie Crocker in comp.dsp7 years ago

Hello All, I am looking to purchase Analog Device, Blackfin Processor ADSP-BF-518BSWZ-4F or -4F4. I need any quantity that you can spare, up...

Hello All, I am looking to purchase Analog Device, Blackfin Processor ADSP-BF-518BSWZ-4F or -4F4. I need any quantity that you can spare, up to 5k. My customer can not wait the lead time. Can you refer me to any manufacturers that may use this item, and have excess inventory to spare? Any help that you could provide would be greatly appreciated! Thanks, Tiffanie Crocker Uniquip Plu...


Softcore for ADSP-2181/2191

Started by SpiffyGuy in comp.dsp12 years ago 4 replies

Hello, Does anyone know of a softcore for either the Analog Devices ADSP-2191 or 2181 DSPs? Looks like the 2191's life is only 2 years and I...

Hello, Does anyone know of a softcore for either the Analog Devices ADSP-2191 or 2181 DSPs? Looks like the 2191's life is only 2 years and I need something that is code compatible with the 2181 DSP. Thanks!