Unable to simulate INT0 interrupt in Code composer studio

Started by gane...@gmail.com in comp.dsp9 years ago

hi all, im unable to generate INT0 interrupt in simulator after doing the "PIN CONNECT" specified in help (Tools --> Pin connect) and...

hi all, im unable to generate INT0 interrupt in simulator after doing the "PIN CONNECT" specified in help (Tools --> Pin connect) and the input .dat file has 55 85 99 rpt 111|EOS data,i could not see the INT0 ISR being served while Timer_ISR is being served as xpected how could generate the INT0 interrupt in simulator mode and cross check it..? Thanks, Ganesh


TI's USCIF driver

Started by mamad13e in comp.dsp8 years ago 1 reply

hello when i try to connect to a "F28335" an error appear in code composer studio that says: Error connecting to the target: Error...

hello when i try to connect to a "F28335" an error appear in code composer studio that says: Error connecting to the target: Error 0x80000240/-604 Fatal Error during: Initialization, OCS, This error was generated by TI's USCIF driver. SC_ERR_LIB_ANY_LOAD A required dynamic library could not be installed. The attempt to load or install the library failed. what should i do? would


Code Composer Studio Code for A Law MU Law implementation

Started by anup_navy in comp.dsp8 years ago 4 replies

Dear ALL I would be thankful to all if anyone can kindly guide me with the coding of A Law and MU Law compander for TMS320C5510 in Code...

Dear ALL I would be thankful to all if anyone can kindly guide me with the coding of A Law and MU Law compander for TMS320C5510 in Code Composer Studio. I have been stuck on this with quite a few days. Also if anyone can please let me know whether some MATLAB code exists for DOA estimation using Acoustic Vector Sensor where the inputs are pressure and particle velocity from 3 axes. Thank...


need AGC algoritm source code using DSK TMS320C6713

Started by Heni Rianti in comp.dsp8 years ago 1 reply

I need AGC algoritm source code using DSK TMS320C6713 like : : "if ( signal_too_big() ) decrease_gain_quickly; else { if (...

I need AGC algoritm source code using DSK TMS320C6713 like : : "if ( signal_too_big() ) decrease_gain_quickly; else { if ( signal_below_threshold() and gain_not_too_high_already() ) { increase_gain_slowly; } }" I've been source code AGC with Matlab and it was implemented in CCS (Code Composer Studio) but it still can't. CCS is software for my board DSK TMS320C6713. ...


Code Composer Studio

Started by Steffen Koepf in comp.dsp8 years ago 1 reply

Hello, i try to compile a old project with the CCS 3.3 It fails with a linker error: --------------------------- abc_flash.pjt - Debug ...

Hello, i try to compile a old project with the CCS 3.3 It fails with a linker error: --------------------------- abc_flash.pjt - Debug --------------------------- [Linking...] "C:\CCStudio_v3.3\C2000\cgtools\bin\cl2000" -@"Debug.lkf" > > E:\work\ABC Prog\32 - V2_1\Quellcode\code\abc\abc_flashcfg.cmd, line 218: error: can't find input file 'biosi.a28l' > > C


DSP project

Started by freedom 85 in comp.dsp7 years ago

i doing the project AM-SSB modulator using code composer studio TMS320C6713. And is almost finish but the output samples have some problem and i...

i doing the project AM-SSB modulator using code composer studio TMS320C6713. And is almost finish but the output samples have some problem and i found the problem is how to make the input samples read from the AIC23 codec ADC to the AIC23 codec DAC as the output samples ....


CCS v5 Error

Started by leomhb in comp.dsp7 years ago 6 replies

Dear Folks, I am working with Code Composer Studio v5 and TMS320F2812. I am facing with the following errors, even for Hello World sample...

Dear Folks, I am working with Code Composer Studio v5 and TMS320F2812. I am facing with the following errors, even for Hello World sample program. Thanks, Amir ................. **** Build of configuration Release for project ssr **** C:\Program Files (x86)\TI\ccsv5\utils\bin\gmake -k all 'Building target: ssr.out' 'Invoking: C2000 Linker' "C:/Program Files (x86)/TI/ccsv5/tools...


FFT calculation problem using TMS320C6416

Started by chokry in comp.dsp4 years ago

Hello to all , I am pretty new to this subject so please bare with me ..I am just trying to do a basic FFT calculation code using the Code...

Hello to all , I am pretty new to this subject so please bare with me ..I am just trying to do a basic FFT calculation code using the Code Composer Studio (CCS v5) my goal is to see the number of clock cycles to compute a Radix-2 FFT; the input is a 256 points sine wave, now if i try to see the FFT magnitude which is supposed to be a dirac impulse, the plot comes out to be random..i'll put my ...


Using TMDX5505EZDSP Processor

Started by nishantprakash in comp.dsp4 years ago 2 replies

I recently bought a TMDX5505EZDSP processor and installed code composer studio for DSP algorithm implementation purpose. I do have very...

I recently bought a TMDX5505EZDSP processor and installed code composer studio for DSP algorithm implementation purpose. I do have very good experience in the Software side of Signal Processing but don't have much exposure in using the DSP Processors so go this processor. Please suggest me some resources to start with. I want to implement the common DSP algorithms in processors and then build upo...


DSK6713/CCS3.1 on Windows Vista

Started by frq789 in comp.dsp4 years ago 9 replies

I bought DSK6713 some time ago, to use with my Windows XP laptop. The DSK came with Code Composer Studio v3.1. I also have a desktop PC with...

I bought DSK6713 some time ago, to use with my Windows XP laptop. The DSK came with Code Composer Studio v3.1. I also have a desktop PC with Windows Vista. Due to work and family life, I couldn't find time to use it for several years. In the meantime, I wiped XP from my laptop and installed Ubuntu. Now I intend to use the DSK once again for my personal learning but can't do it because of th...