Forums Search for: DSP Boards
Need help for ADSP TS 101S EZ-Lite Board
inhi, greetings, I am doing a project using ADSP TS 101s EZ-Lite board. The problem is like this: I have some data between 0 and 1, and I...
hi, greetings, I am doing a project using ADSP TS 101s EZ-Lite board. The problem is like this: I have some data between 0 and 1, and I will output these data to the linkport on this board. I want to find a device that convert this data to a PWM generator as the duty cycle input. Any input is highly appreciated. thanks paul
ccs problem
inHi everyone, I am having a spectrum digital emulator board with TMS320c5416 dsp. I bought that and i installed the CCS in my desktop. When I...
Hi everyone, I am having a spectrum digital emulator board with TMS320c5416 dsp. I bought that and i installed the CCS in my desktop. When I connect the board and start the CCS, the USB is enumerated but then a error window is coming. It is like this title of the window: CPU_1- DSP DEVICE DRIVER. CONTENT: CAN'T INITIALIZE TARGET CPU I/O PORT : 540 BOARD NAME: SDGO5416DSK (SPECTRUM DIGITA...
EMIF(parallel 16) boot from flash on5502 giving problems
Hi I have a custom 5502 board. I have been able to write code to it's SDRAM and execute form there. My problems (unexpectedly) are...
Hi I have a custom 5502 board. I have been able to write code to it's SDRAM and execute form there. My problems (unexpectedly) are coming from flash. i can access it's flash when i burn my code in it and using flashburn i also compared the flash contents of my board versus the EVM5502 board and i found that they were the same. My GPIOs are always(before reset adn after reset i have ...
Evaluation Board
inHi, I'm looking to buy a DSP evaluation board to play around with in my sparetime. I prefer fixed-point DSPs, but floating-point is also...
Hi, I'm looking to buy a DSP evaluation board to play around with in my sparetime. I prefer fixed-point DSPs, but floating-point is also ok. Audio sampling rate should be minimum 24kHz. The board is primarily going to be used for audio signal processing applications (hearing aids). Requirements: * Algebraic assembly language (like the algebraic assembly syntax of Analog Device...
CCS problem
Hi everyone, I am having a spectrum digital emulator board with TMS320c5416 dsp. I bought that and i installed the CCS in my desktop. When I...
Hi everyone, I am having a spectrum digital emulator board with TMS320c5416 dsp. I bought that and i installed the CCS in my desktop. When I connect the board and start the CCS, the USB is enumerated but then a error window is coming. It is like this title of the window: CPU_1- DSP DEVICE DRIVER. CONTENT: CAN'T INITIALIZE TARGET CPU I/O PORT : 540 BOARD NAME: SDGO5416DSK (SPECTRUM DIGITAL) ...
board protection
indo you guys have any suggestions on how to make a protection circuit for the tms320f2812 ezdsp board so it would be robust when input signals...
do you guys have any suggestions on how to make a protection circuit for the tms320f2812 ezdsp board so it would be robust when input signals are applied? thank you :)
Q: op-amp to protect DSP board?
inHello, I recently got an ADUC831 microconverter board, and am interested in experimenting with DSP applied to an audio input and/or output....
Hello, I recently got an ADUC831 microconverter board, and am interested in experimenting with DSP applied to an audio input and/or output. A friend who is knowledgeable about these boards recommended "passing audio input through an op-amp to protect the board." His meaning appears to be that I should connect my 1/8 in. jack to an op-amp, and the op-amp to the ADC input, in such a way th...
Software PLL
inI'm looking for guidance on writing a software PLL for a signal acquired from a data acquisition board: The daq board will be sampling at...
I'm looking for guidance on writing a software PLL for a signal acquired from a data acquisition board: The daq board will be sampling at 10kSPS. The signals to which I'd like to lock on to are from 5Hz to 1kHz, sine or square wave. The output of the PLL will be used to multiply a signal acquired on an adjacent channel of the daq board. Lock-in amplifier application. The processing of the sig...
Eval Board with SAR ADC
inHello everyone, it's been a while ago since someone asked here for an DSP eval board (for audio processing) that's got a SAR analog-digital...
Hello everyone, it's been a while ago since someone asked here for an DSP eval board (for audio processing) that's got a SAR analog-digital converter. Theoretical it should be possible to reach very low delay between an audio input and the output after processing by a DSP. Does anyone know a device with a fast SAR ADC (that could be used for audio processing)? A board with suiting anti-aliasi...
How can I surpress noise in an ADC board?
inWhile I have only a 40MHz clock connected to a 10 bit ADC, nothing connected to the analog input sockets, the chip is Analog AD9218 (ADC chip)...
While I have only a 40MHz clock connected to a 10 bit ADC, nothing connected to the analog input sockets, the chip is Analog AD9218 (ADC chip) EVM board. On the LA, sampled outputs are 0~16 for one channel, -32~0 for the other channel (400 MHz timing mode). Is my board faulty? According to my simulation in digital design, my sampled inputs (10 bits each) can not have noise higher than 1 ...
looking for DSK C6416 ready to exchang with our DM6437
Hi We have a new evaluation board DM6437 (in the original BOX) We just finished developing a daughter card with LATTICE FPGA...
Hi We have a new evaluation board DM6437 (in the original BOX) We just finished developing a daughter card with LATTICE FPGA machXO2280 connected on the DSK C6416 dither card connectors. (With two UART on it, that work OK) 1. We would like to exchange the evaluation board DM6437 with your evaluation board DSK D6416! 2. we want to buy another DSK C6416 immediately! Is there anybody to sell ...
PCI board with motor control DSP
inDoes anyone make a PCI development board with a motor control DSP? ADI and TI have standalone development boards for the 21992 and F2808,...
Does anyone make a PCI development board with a motor control DSP? ADI and TI have standalone development boards for the 21992 and F2808, respectively, but I'd like something that plugs into a PC's PCI bus. Does anyone have a PCI board with a general purpose DSP and a motor control front-end like the TI ADS7869?
Recommendations on Floating Point DSP Eval Boards w/ Samplers
Hello all, I've been hunting the web for a DSP evaluation board with the following criteria: 1) Floating Point DSP Processor 2) C programming...
Hello all, I've been hunting the web for a DSP evaluation board with the following criteria: 1) Floating Point DSP Processor 2) C programming capabilities 3) On board sampler. 50-100 MSPS (~20MHz bandwidth RF signals) 4) Standard I/O features (USB or Serial, etc) The thing that I find hardest to locate is the on-board sampler. Most eval boards only offer audio samplers. Do these types of...
Re: Flashburn on DM642 EVM board
inHi, I am having difficulties trying to flashburn led.hex (created from led.out) onto DM642 EVM board. From my understanding, it is only...
Hi, I am having difficulties trying to flashburn led.hex (created from led.out) onto DM642 EVM board. From my understanding, it is only after the FPGA is programmed via the fpga_loader program that I will be able to modify the FPGA Flash Page Register to boot my application code from PAGE1. So if I were to flashburn my application onto DM642 EVM board,I would have to: 1.) flashburn my...
Motorola Audio EVM Board with DSP56371 Daughter Board for sale
inHi all, is there anyone who need an 56371 EVM Board for Audio DSP? The Board is originally Motorola. There are 6 x Stereo output (chinch) 2 x...
Hi all, is there anyone who need an 56371 EVM Board for Audio DSP? The Board is originally Motorola. There are 6 x Stereo output (chinch) 2 x Mic input (3.5mm jack plug) 1 x Headphone (3.5mm jack plug) 4 x S/PDIF output el. (chinch) 2 x S/PDIF input el. (chinch) 1 x S/PDIF output opt. (Toshlink) 2 x S/PDIF input opt. (Toshlink) PC connectoers: 1 x serial 1 x parallel 1 x USB Ext. po...
EMAC on DM64x
Hello. Have anybody information, maybe code examples, of implementing EMAC and MDIO modules on DM642 and exchanging data between PC and board...
Hello. Have anybody information, maybe code examples, of implementing EMAC and MDIO modules on DM642 and exchanging data between PC and board by any of the net protocols? PHY device, which being used on board, is LXT972A. I'm now is beginner of the realizing the task, so need help from experts. Best regards, Alexey.
EMAC on DM64x
Hello. Have anybody information, maybe code examples, of implementing EMAC and MDIO modules on DM642 and exchanging data between PC and board...
Hello. Have anybody information, maybe code examples, of implementing EMAC and MDIO modules on DM642 and exchanging data between PC and board by any of the net protocols? PHY device, which being used on board, is LXT972A. I'm now is beginner of the realizing the task, so need help from experts. Best regards, Alexey.
CRO PCI board
inCould anyone suggest me if the is PCI board that acts as CRO. I believe such a product should of low cost. Is there one which is less than...
Could anyone suggest me if the is PCI board that acts as CRO. I believe such a product should of low cost. Is there one which is less than US$200 bala
"Maker board"
inI've recently seen in job listings, contract requirements etc. references to desiring engineers who are "experienced with Maker boards". What...
I've recently seen in job listings, contract requirements etc. references to desiring engineers who are "experienced with Maker boards". What exactly is a Maker board? I gather it's not a brand name, but some general concept ... it sounds a little new-age or something. Is there a specific meaning? Steve
c6711 data transfer
inHello, I am trying to use a c6711 for a controls project. This board does not have a GPIO since it is the first revision. I want to know if...
Hello, I am trying to use a c6711 for a controls project. This board does not have a GPIO since it is the first revision. I want to know if there is any way to input/output to the board (from an analog circuit) without buying any daughter card. Thanks in advance for your response, memo This message was sent using the Comp.DSP web interface on DSPRelated.com