c6416 pci boards

Started by Shay Avivi in comp.dsp13 years ago

Hi everyone, I'm looking for a pci board for TI's tms320c6416, it's critical that the board will have a PCI interface...

Hi everyone, I'm looking for a pci board for TI's tms320c6416, it's critical that the board will have a PCI interface (not PC104/PCI104) I'll also need 3 McBsp to connect to ADC's an EMIF connection could also be useful... boards with onboard ADC's are also welcomed any recommendation or thoughts on the subject will be appreciated! Thanks, Shay Avivi


DSP with fast A/D

Started by Paul Lovell in comp.dsp15 years ago 7 replies

Hi all, I'm looking for a starter or evaluation DSP board with a fast (> 20Mb/s) A/D converter, for a DSP radio project. This could be either...

Hi all, I'm looking for a starter or evaluation DSP board with a fast (> 20Mb/s) A/D converter, for a DSP radio project. This could be either on-board, or a separate unit, but it would be nice if the two were compatible to start with, rather than requiring a lot of interfacing. The DSP kits I've seen seem to only have audio A/D converters. Would prefer TI or ADI DSP. Any ideas appreciat


3in1 DSP CPLD MCU Demonstration Board ti altera atmel

Started by ssy in comp.dsp11 years ago

Hello everyone, I'd like to learn how to program a TI DSP and came across the following board on eBay for a 3 in 1 combo containing the TI...

Hello everyone, I'd like to learn how to program a TI DSP and came across the following board on eBay for a 3 in 1 combo containing the TI TMS320VC5402: http://item.express.ebay.com/ws/eBayISAPI.dll?ExpressItem&item=290191396087&FROM_MERCHANDIZING=1 QQssPageNameZKP_Merch_CLOSED_ITEM_SIMILAR_LINK It comes with no programming tools, and I have been unable to get more information about the b


Interfacing C6713 DSK

Started by Bakari in comp.dsp13 years ago

I need to interface the C6713 DSK to my own daugter board. In doing that, I will need ECLKOUT which I will use to drive the logics in my daugter...

I need to interface the C6713 DSK to my own daugter board. In doing that, I will need ECLKOUT which I will use to drive the logics in my daugter board (EMIF). How can I get this signal out of the SDK. I expected that this signal is available as soon as the DSP is ready. Thanks for your help. Bakari


ADC Board with DSP

Started by MarcosOmni in comp.dsp13 years ago 2 replies

Hello, I am looking for a ADC Board with DSP . I have been searching through google but unfortunately I have no success. Does anyone know...

Hello, I am looking for a ADC Board with DSP . I have been searching through google but unfortunately I have no success. Does anyone know commercial boards with the following characteristics? Computer bus: PCI At least 2 A/D channel Resolution: 8 bits or higher Sample frequency: 10MHz or higher With DSP (for my own algorithms) Drivers for Linux Thanks in advance, Marcos Vi...


ADSP 21161N ez_kite_lite, english

Started by chris_08 in comp.dsp14 years ago 1 reply

Hello! I am a student of the TGM a technical college in Vienna. I use the ADSP 21161N_ez_kite_lite board with a SHARC processor. I need...

Hello! I am a student of the TGM a technical college in Vienna. I use the ADSP 21161N_ez_kite_lite board with a SHARC processor. I need help because I want to receive some signals (HIGH/LOW) from an external board which is connected to a port from the DSP. The signals will be used by the application. I have problems to address each bus-line from the port separate. I tried this by the ...


Help identifying old DSP board - Motorola DSP56002

Started by Mark Atherton in comp.dsp9 years ago 1 reply

Hi All, Just been given this old DSP dev board http://www.idesignz.org/misc/MotDSPboard.jpg AES/EBU connector bottom right (looks like...

Hi All, Just been given this old DSP dev board http://www.idesignz.org/misc/MotDSPboard.jpg AES/EBU connector bottom right (looks like someone has taken the TX and RX chips) DSP56002, 57C219 EPROM, MCM6290 RAM Any help identifying it also data sheet, schematic most appreciated. Thanks, Mark


Multichannel RF filter

Started by dpkelly in comp.dsp10 years ago

I'm somewhat new to the DSP world and would like some help in recommending a particular board for my application. I would like to filter...

I'm somewhat new to the DSP world and would like some help in recommending a particular board for my application. I would like to filter multiple channels in the RF spectrum. The RF spectrum would be downconverted to the bandwidth of the particular board. The maximum RF spectrum width would be 60MHz. One channel bandwidth would be 12.5kHz with adjustments to 100kHz. I would like to filter...


eZdsp F2812 and PC

Started by pawl in comp.dsp13 years ago 2 replies

Hello, I have an eZdsp F2812 Board connected with a PC through a parallel port. On the DSP there is my program, which is running with a...

Hello, I have an eZdsp F2812 Board connected with a PC through a parallel port. On the DSP there is my program, which is running with a frequency of 20kHz. I would like to send some data from the board to the PC, where there will be a simple GUI to control the behavior of my program. Could you tell me the easiest solution for this? How to write a routine which sends the data from the D...


eZdsp with TMS320F2812 - A/D converters

Started by Anonymous in comp.dsp14 years ago 3 replies

Hello, for my project I've bought the Spectrum Digital board with the TMS320F2812 DSP. I have chosen it because it has A/D converters and PWM...

Hello, for my project I've bought the Spectrum Digital board with the TMS320F2812 DSP. I have chosen it because it has A/D converters and PWM units on board. Yesterday I met a man from a company in Germany and he told me that the converters of the processor are very bad. He would measure the DC signal, and what he got was something that from 12-bit signal only 7 bits were stable. He sa...


TMS320R2811 JTAG communication

Started by Korenje in comp.dsp14 years ago 4 replies

Hello, I have built a board with TMS320R2811 on it. When I power it up oscillator works, and on RS pin I can see the watchdog reset as it...

Hello, I have built a board with TMS320R2811 on it. When I power it up oscillator works, and on RS pin I can see the watchdog reset as it is supposed to, so I assume that the core is alive. But I can not communicate with the DSP, through JTAG with XDS510PP+. I connected all the JTAG pins as they are supposed to (according to ezDSP R2812 schematics). I had no problems with my previous board...


New to EZ-Kit 213xx

Started by Matthieu in comp.dsp14 years ago 2 replies

Hello, I just received my EZ-Kit 21364 evaluation board. I've runned some examples provided with VDSP 4.0, and I looked to the source code,...

Hello, I just received my EZ-Kit 21364 evaluation board. I've runned some examples provided with VDSP 4.0, and I looked to the source code, etc. I'm also currently reading the hardware reference of the 21364 processor. I want to write a simple LPF/HPF to get my hands on with the processor and board, but I have a few questions : - I tried the basic analog audio talktrough C example (whi...


PC to DSP communication

Started by josam in comp.dsp6 years ago 4 replies

Hi All, I am quite new to DSP programming. I am using DSK6416 and need to pass a text file of integers from my pc to the dsp board in order to...

Hi All, I am quite new to DSP programming. I am using DSK6416 and need to pass a text file of integers from my pc to the dsp board in order to do some processing with this data. The result must than be returned from the dsp board to the PC in order to output the result. If any one of you could help me how to just write 1 number do a multiplication on the DSP and return the answer to the ...


DSP-based underwater acoustic modem

Started by Tomeu in comp.dsp11 years ago 1 reply

Hello. first of all I have to present myself, this is my first post on this board. I'm an electrical engineer from Spain. I have very short...

Hello. first of all I have to present myself, this is my first post on this board. I'm an electrical engineer from Spain. I have very short experience with DSPs, that's why I use this discussion board to learn abot that. We need to develop an underwater acoustic modem for data transmission between underwater sensor nodes. I have been investigating different approaches to the problem. The senso...


matlab & ccs interfacing

Started by vasu in comp.dsp13 years ago 2 replies

we are currently working on echo cancellation using adaptive filtering on dsk 6713. we have implemented fir low pass and high pass filters on...

we are currently working on echo cancellation using adaptive filtering on dsk 6713. we have implemented fir low pass and high pass filters on the board using CCS. we have developed L.M.S algorithm in Matlab(Not the Blockset provided in Help. A new one). we want to download that m file on the board(Portability between Matlab and Code Composer Studio). How ?


LF2402 Flash Password

Started by Martin Rose in comp.dsp16 years ago 1 reply

Hi, today I created a prototype board with a TMS320LF2402. After I finally managed to get the serial bootloader running I accidantly changed...

Hi, today I created a prototype board with a TMS320LF2402. After I finally managed to get the serial bootloader running I accidantly changed the password by loading the new hex file into the flash. I wanted to test the board with a very simple prgramm I found on a germany universities website. It was originally writen for the LF2407. Now I have to find out what words have been written to 0x4...


Recommendation for PCI DSP board?

Started by Robert Latest in comp.dsp13 years ago 4 replies

Hello, For a laoboratory measurement control / data acquisition system I'd like to use a DSP board that plugs into a standard PC. A nice,...

Hello, For a laoboratory measurement control / data acquisition system I'd like to use a DSP board that plugs into a standard PC. A nice, low-cost card that fits the bill is this one: http://www.signalogic.com/index.pl?page=pc32 However, it only comes with an ISA slot. All PCI cards that I could find are much more expensive and have tons of additional performance that I don't need. ...


Analog Devices ADAU1761

Started by rickman in comp.dsp10 years ago 5 replies

I am contemplating adding a DSP to a design with very, very little board space. The current design uses a small FPGA and a stereo CODEC to...

I am contemplating adding a DSP to a design with very, very little board space. The current design uses a small FPGA and a stereo CODEC to receive or transmit a time code signal that uses a PWM symbol coding modulated on a 1 kHz carrier. When I was designing the board the customer asked me to make it flexible enough to use it for other work including telephony and "high resolution" audio. ...


Help needed with TI C6711 DSK

Started by L. Bawr in comp.dsp15 years ago 6 replies

Hi everyone, I am looking for a trick to output 6 (binary) signals simultaneously from the C6711 DSK board to feed a RF circuit. To retrieve...

Hi everyone, I am looking for a trick to output 6 (binary) signals simultaneously from the C6711 DSK board to feed a RF circuit. To retrieve these signals from the board I would like to avoid any external module (daughter card or home made circuits) because we have a limited budget for a small demo. I know c6x Dsp's have GPIO registers that might be very useful but I don't how to make a c...


Finding the right DSP evaluation board

Started by Zach R. in comp.dsp16 years ago 2 replies

Hi everyone, I am looking for a floating point evaluation board that has easy audio inputs (such as rca or 3.5mm jacks) and a SAR adc. I...

Hi everyone, I am looking for a floating point evaluation board that has easy audio inputs (such as rca or 3.5mm jacks) and a SAR adc. I have almost exactly what I want in the ADSP BF533 but I am getting a group delay due to the sigma-delta converter. Some of you on here let me know that I needed to use a SAR adc for feedback control applications. So I need to find a new evaluation boar...