DSPB56367AG150 problem

Started by Roman Rumian in comp.dsp7 years ago

Hello Friends, this summer I bought from big distributor in USA 14 pieces of Freescale DSPB56367AG150 signal processor chip, and last week...

Hello Friends, this summer I bought from big distributor in USA 14 pieces of Freescale DSPB56367AG150 signal processor chip, and last week they were soldered to small PCB module. First simple tests showed that all of them are dead: no debug communication(JTAG), no external activity (booting). Distributor support says, that parts were shipped directly from silicon fab in Malesia. So, I...


Low pass MAC Filter incorrect response

Started by Bryan in comp.dsp13 years ago 2 replies

Hi all, thanks to your help, I have managed to solve the JTAG problem on my XTREME DSP Development Kit. However I had a response which...

Hi all, thanks to your help, I have managed to solve the JTAG problem on my XTREME DSP Development Kit. However I had a response which attenuates all frequencies even though my design is low pass filter.. Anybody can help me with that because i checked through my design n it seems fine. It is a MAC based FIR 43 tap filter though.


[F2812 EZDSP] Inaccurate timing executing code relocated from Flash

Started by seankuay in comp.dsp12 years ago 2 replies

Hi Expers I am now using the eZdsp board to perform some tasks on the GPIO of TMS320f2812 dsp controller, 150 mhz. PROBLEM...

Hi Expers I am now using the eZdsp board to perform some tasks on the GPIO of TMS320f2812 dsp controller, 150 mhz. PROBLEM SCNENARIO: =================== 1. When i run from JTAG emulator (execute completely in RAM), i am able to control the output timing of GPIO pin very accurately by 6.7ns per NOP operation (1 isntruction). This means i can get the 150 Mhz as state by the. HO...


Unable To Clear TMS320LF2406A

Started by Kris Paciura in comp.dsp15 years ago 1 reply

Hi there if sombody could help me with this problem. I was using my pcb with TMS320LF2406A processor and everything was ok suddenly the...

Hi there if sombody could help me with this problem. I was using my pcb with TMS320LF2406A processor and everything was ok suddenly the error Unable To Clear stoped me and now I can not program it anymore. I was try using Jtag and RS232 Processor still works but I can not upload new software I try to unlock password with numbers in 0x0040 0x0041 0x0042 0x0043 but it does not work. If anybod...


SHARC debug

Started by Anonymous in comp.dsp15 years ago 14 replies

I'm having a hard time trying to find documentation on how to use SHARC's JTAG port for debugging. I'm evaluating the ADSP-21363. Do I have...

I'm having a hard time trying to find documentation on how to use SHARC's JTAG port for debugging. I'm evaluating the ADSP-21363. Do I have access do all internal memory. What are the commands to do it? How so set a break point? Can I check for memory invasion? What's the tranfer rate (for reading/writing the internal memory)? I don't want to use an ADI emulation pod. Luiz Carlos.


CCStudio fatal error OCS during connection

Started by eeh in comp.dsp15 years ago 1 reply

Hi, Recently a DSP project is assigned to me which uses one TMS320C6711 DSP chip to do filtering work. However, a problem is encountered...

Hi, Recently a DSP project is assigned to me which uses one TMS320C6711 DSP chip to do filtering work. However, a problem is encountered which makes me very trouble when connect the target board to CCS. The emulator I used is XDS510PP plus from Spectrum Digital. SDConfig can detect there is one JTAG device in the target side. Then I setup the CCS to use sdgo6x driver. But a fatal error i...


Problem with the communication between DSP and JTAG

Started by sunn...@126.com in comp.dsp14 years ago 9 replies

Hello,everyone! My question is : When I click CCS, I can not enter into it.At the same time,I checked 1. the signal of TDI only changed...

Hello,everyone! My question is : When I click CCS, I can not enter into it.At the same time,I checked 1. the signal of TDI only changed once,then it kept high. 2. the signal of TDO did not change at all. 3. TRST changed from low to high, then kept high. 4. RESET had no changes, but kept high all the time. I try it again and again, everytime I got the same result. Can you tell me why, thank...


Q: Ad's VisualDSP (for Blackfin) with VMWare ?

Started by Karl M. Prager in comp.dsp15 years ago 4 replies

Hi! I am planning to use VisualDSP for a Blackfin project. Now, as we are working only with Linux - have one of you gurus today...

Hi! I am planning to use VisualDSP for a Blackfin project. Now, as we are working only with Linux - have one of you gurus today running the VDSP with W2000 by VMWare under Linux _and_ is able to use the USB-JTAG emulator? I googled only one negative report of this group five years ago. Is it working now? Thanx, Charlie


I can't link ccs with my c6713 board by JTAG

Started by sunn...@126.com in comp.dsp14 years ago 1 reply

After I have setup the ccs in the condition of c671x XDS510 Emulator and want to enter into the enviroment of ccs , but it failed .It...

After I have setup the ccs in the condition of c671x XDS510 Emulator and want to enter into the enviroment of ccs , but it failed .It give me the error message as follows : Can't Initialize Target CPU: Error 0x80000200/-1031 Fatal Error during : 0CS, Device Driver: Problem with Emulation Controler. It Recommended to RESET Emulator.This will disconnect each target from the emulato...


CCS 3.0 symbol table change

Started by Anonymous in comp.dsp15 years ago 1 reply

We have a third party tool which reads the symbol table and communicates to the DSP over different interfaces (serial, JTAG, etc..) This tool...

We have a third party tool which reads the symbol table and communicates to the DSP over different interfaces (serial, JTAG, etc..) This tool has been in use for approximately 10 years and has worked with many versions of the TI tools. (C2x, 3x, 4x, 54, 55, 67...) Using the CCS 3.0.0.21 tools for the C67, the structure information we need is no longer in the symbol table but the watch...


5402 External flash Programming

Started by Dinesh Rode in comp.dsp11 years ago

Hi All, I am facing one problem while downloading code into 5402 using XDS510PP Plus. I have interfaced AM29LV160DB, 1Mx16 Flash to 5402 and I...

Hi All, I am facing one problem while downloading code into 5402 using XDS510PP Plus. I have interfaced AM29LV160DB, 1Mx16 Flash to 5402 and I have connected MP / MC pin Vcc (Microprocessor Mode). Can anybody tell me how to download code into external flash using CCS and JTAG emulator? Thanks, Dinesh


Problem running the examples on EVMDM642 board

Started by arichard in comp.dsp14 years ago

Dear Experts, I am having problems running the examples provided with the EVMDM642 board together with the USB XDS510 JTAG emulator. I tried...

Dear Experts, I am having problems running the examples provided with the EVMDM642 board together with the USB XDS510 JTAG emulator. I tried to run the executables as it came with the product and I already tried to compile the examples under CC 3.1 (with no errors), but in either cases every time I run an example the screen becomes pink/grey and the color bars disappear, instead of viewing...


JTAG emulator doesn't work on target board! Please help!

Started by Christian in comp.dsp16 years ago 4 replies

Hi there! I've got a problem with my DSP target board. I'm currently using an XDS510PP plus Emulator (from spectrum digital) and a target...

Hi there! I've got a problem with my DSP target board. I'm currently using an XDS510PP plus Emulator (from spectrum digital) and a target board with one single TMS320VC5409 CPU. Also changed to C5416 without affect. I'm currently using CCS free evaluation tool v.2.21 from texas on a Win 2000 machine. When the emulator is connected to the C5416DSK, all functions well. But when I conn...


Oops! Analog Devices AD14060 Board

Started by Al Clark in comp.dsp9 years ago

(Oops!, Actually AD14060 or AD14060L, last post was wrong part number ) I am potentially working on an existing product that uses an ADI...

(Oops!, Actually AD14060 or AD14060L, last post was wrong part number ) I am potentially working on an existing product that uses an ADI AD14060 (Quad SHARC). My task is strictly software. I might like to buy a working board that includes this processor and a JTAG connection. Does anyone have something that might work? Al Clark Danville Signal


TMS320F28335 Flash Programming

Started by polpet in comp.dsp12 years ago 4 replies

Dear all, I have developed a firmware application for my TMS320F28335 with the help of Code Composer Studio and the eZdspf28335. The...

Dear all, I have developed a firmware application for my TMS320F28335 with the help of Code Composer Studio and the eZdspf28335. The application works (quite) well in debug mode, thus I want to finally program the flash on-chip memory in order to have the dsp working immediately after a reset without the need of the jtag interface and debug. Now I'm trying to understand how to program the...


LF240xA hardware: JTAG debugging from flash

Started by Tony McKay in comp.dsp17 years ago 1 reply

Hello I am using CCS 2.2 to create a program for the LF240xA from TI. I have made a blinking LED program to test my own target board with,...

Hello I am using CCS 2.2 to create a program for the LF240xA from TI. I have made a blinking LED program to test my own target board with, the "hello world" of embedded. I compiled it and then used the "flash programmer" plugin to load it to a board with a LF2402A on. With out doing anything else I can now "reset cpu" and "run". I tried a suggestion from Trampas to use the "load program"...


Setup Code Composer Studio for TMS320F2808? (HELP)

Started by Moppe in comp.dsp14 years ago 2 replies

How do I setup Code Composer Studio v2 to compile for the TMS320F2808? And how do I setup my XDS510PP PLUS JTAG Scan Path Emulator to work...

How do I setup Code Composer Studio v2 to compile for the TMS320F2808? And how do I setup my XDS510PP PLUS JTAG Scan Path Emulator to work with this DPS? I suspect that I must download a lot of updates?


Visual DSP JTAG connect / disconnect will switch source files in editor

Started by Andre in comp.dsp9 years ago

Hi all, this may be a bit off topic, however: Has anybody found a way to prevent that ADIs Visual DSP switches the source files opened in...

Hi all, this may be a bit off topic, however: Has anybody found a way to prevent that ADIs Visual DSP switches the source files opened in the editor when connecting / disconnecting with a target? I find this quite annoying, I often switch between online and offline but want to keep the same files open... best regards, Andre


RTDX Interupt Problem (Probably)

Started by jcockburn in comp.dsp14 years ago 1 reply

Hi, I'm doing a student project and I have made a simple graphic equalizer using a c6711 DSK. I am trying to write a host application to put a...

Hi, I'm doing a student project and I have made a simple graphic equalizer using a c6711 DSK. I am trying to write a host application to put a pretty user interface on the equalizer using RTDX (JTAG, not HSRTDX) to send the positions of several sliders to the DSK. I have successfully written the host program, and a corresponding target application that reads the values that are written and p...


Code composer Studio 2 and Windows 2000 pro

Started by Lotfi in comp.dsp11 years ago 4 replies

Hi We have many licences of Code Composer 4.1x and now the CCS 2 for TMS320 F240. When installing CCS2 and Spectrum digital drivers (F24x...

Hi We have many licences of Code Composer 4.1x and now the CCS 2 for TMS320 F240. When installing CCS2 and Spectrum digital drivers (F24x EVM with JTAG interface) on Microsoft W2000 pro systems, it lets only the administrator to use them. Normal Users (privilege) can not start CCS2. Can you help us and tell me how to install the CCS2 tool for users that have restricted privileges on th...