Question about PC Host and DSK Communication with 6416 DSK

Started by dann in comp.dsp15 years ago 2 replies

Hi, everyone. I need some help from you, guys. I have 6416 DSK of SpectrumDigital co., which is connected to my PC (Window XP based) with USB...

Hi, everyone. I need some help from you, guys. I have 6416 DSK of SpectrumDigital co., which is connected to my PC (Window XP based) with USB connect (not JTAG XDS510 USB). The 6416 DSK itself supports USB connection. I also have Code Composer Studio v2.2 and MS Visual C++ v6. The prgogram that I wanna make is a PC and DSK communication program. The file (bigger than 1MB) is loaded in P...


Not a DSP Question

Started by k in comp.dsp16 years ago 2 replies

I am trying to source level debug my embedded code thru a JTAG emulator. I am using gcc. At the moment I am generating a motorola hex file format...

I am trying to source level debug my embedded code thru a JTAG emulator. I am using gcc. At the moment I am generating a motorola hex file format that does not contain any debug information. What type of file I need to generate with gcc that allows me to source level debug and how do I generate this file. Thanks Carl


[F2812 EZDSP] Inaccurate timing executing code relocated from Flash

Started by seankuay in comp.dsp11 years ago 2 replies

Hi Expers I am now using the eZdsp board to perform some tasks on the GPIO of TMS320f2812 dsp controller, 150 mhz. PROBLEM...

Hi Expers I am now using the eZdsp board to perform some tasks on the GPIO of TMS320f2812 dsp controller, 150 mhz. PROBLEM SCNENARIO: =================== 1. When i run from JTAG emulator (execute completely in RAM), i am able to control the output timing of GPIO pin very accurately by 6.7ns per NOP operation (1 isntruction). This means i can get the 150 Mhz as state by the. HO...


Connect XDS510PP with C6713

Started by Jaradi Rohan in comp.dsp10 years ago

Hello, I am trying to connect XDS510PP with C6713 but it is not connecting with it. I am getting an this message Error connecting to the...

Hello, I am trying to connect XDS510PP with C6713 but it is not connecting with it. I am getting an this message Error connecting to the target Error 0x80000200/-1063 Fatal Error during OCS, Bad Target Silicon Revision Number...........Please check your multi-processor configuration. The number od the devices in the JTAG scan path............. SO, what should I do now.. Please give me sol...


Way to Download DSP .out file without Code Composer

Started by Ben Nguyen in comp.dsp15 years ago 2 replies

Im looking for a way to just download the dsp .out file from a pc to the dsp via the JTAG emulator pod. Once downloaded, the code can...

Im looking for a way to just download the dsp .out file from a pc to the dsp via the JTAG emulator pod. Once downloaded, the code can flash itself into flash memory. This is for the production people, which dont have the need to compile, debug, simulate, or anything else... they just need to download the executable to the target. The only software that I know can do this (Code Composer...


Help Over Flash programming using XDS510

Started by vijaykumar1981 in comp.dsp11 years ago 2 replies

Hi, I am using XDS510 USB PLUS JTAG Emulator for programming flash inside TMS320F2810. Currently I am achieving this by selecting "Tools->...

Hi, I am using XDS510 USB PLUS JTAG Emulator for programming flash inside TMS320F2810. Currently I am achieving this by selecting "Tools-> F28XX On-chip Flash programmer" option from code composer studio. I am planning to automate programming. I think I can use command line arguements for programming through DOS prompt. I didn't find any help over programming through command line for XDS510 U


Problems programming TMS320F2811

Started by mxcom in comp.dsp11 years ago

can someone please provide some feedback, I have been trying to program TMS320F2811. On my board I have 2 DSP chained together, I am using...

can someone please provide some feedback, I have been trying to program TMS320F2811. On my board I have 2 DSP chained together, I am using code composer 3.1 and JTAG method to program I have downloaded the plugin for the Flash programming. My problem is once I get a new board and open up the Falsh programmer under code composer it says device is locked. I have not locked the device as it is a new ...


Problem with Code composer studio connecting with big endian.

Started by Benne in comp.dsp10 years ago 5 replies

Hi. I have a board with a TMS320C6727. My other equipment is JTAGjet from Signum and Code composer studio 3.3. I can connect with the board...

Hi. I have a board with a TMS320C6727. My other equipment is JTAGjet from Signum and Code composer studio 3.3. I can connect with the board easily. But sometimes it connects with little endian, and sometimes big endian. Both the DSP and the JTAG supports both. However, my piece of firmware which I need to install is only little endian. So sometimes I can't download this piece of firmwa...


Reading file on DM642 with CSS 3.0.0.21

Started by keigo in comp.dsp13 years ago 7 replies

Hi, I need to read in a sequence of raw video file (300 frames, 400MB), and perform video encoding on the C6000 dsp board for benchmarking with...

Hi, I need to read in a sequence of raw video file (300 frames, 400MB), and perform video encoding on the C6000 dsp board for benchmarking with known sequences. I tried using 'fopen' and 'fread' to read/encode frame by frame, however the encoding is far too slow. 10 seconds of video took me hours to encode which should not be the case. Is this mainly due to the file I/O thru JTAG? (as i read...


Problems Booting TMS320VC5509A from serial EEPROM

Started by Felix Collins in comp.dsp15 years ago 1 reply

Hi All, I am having difficulties getting my TMS320VC5509A to boot from serial eeprom. I can successfully boot from USB. I can write and read...

Hi All, I am having difficulties getting my TMS320VC5509A to boot from serial eeprom. I can successfully boot from USB. I can write and read the EEPROM and it appears that the data is being stored in it correctly. I can use the same boot table to boot from USB. When I try to boot from the EEPROM the application does not start properly. Using a Flexds JTAG emulator I have read out part ...


Error Configuring CCS for Mistral Solutions OMAP3530 EVM

Started by tel12345# in comp.dsp10 years ago

Hi, I have a Mistral solutions OMAP3530 board and a XDS510PP jtag Emulator(From digital Spectrum). When I try to configure the board...

Hi, I have a Mistral solutions OMAP3530 board and a XDS510PP jtag Emulator(From digital Spectrum). When I try to configure the board in "CCStudio Setup", using the specific configuration for the mistral board (which is included with the XDS510PP drivers), it gives an error: "Error automatically generating board file. An invalid router family was specified". I am Using Code_Com...


XDS510PP problem

Started by Mike Shonle in comp.dsp16 years ago 1 reply

Target DSP: TMS320LF2407A Target board: eZdsp TMS320lf2407a & custom 1 device in chain. emulator model: XDS510PP Software: Code Composer...

Target DSP: TMS320LF2407A Target board: eZdsp TMS320lf2407a & custom 1 device in chain. emulator model: XDS510PP Software: Code Composer 4.12, sdconfig 1.35 OS: windows 2000 sp 4 PC: Dell Hi, I'm trying to use our XDS510PP JTAG module, initially on the Spectrum Digital eZdsp TMS320LF2407a, and then on our custom board. When I use sdconfig and have the parallel cable plugged dir...


CCS 3.2

Started by mehran_655 in comp.dsp13 years ago 1 reply

Dear all, I have some boards from sundance (SMT310Q: carrier board with JTAG-xds510 SMT361A: DSP TMS320C6416D10), I installed CCS 2.2 but it...

Dear all, I have some boards from sundance (SMT310Q: carrier board with JTAG-xds510 SMT361A: DSP TMS320C6416D10), I installed CCS 2.2 but it couldn't connect to the boards. I installed CCS 3.2(beta 2), It has sundance modules in Code Composer Setup, but the i didn't found modules SMT310Q & SMT361A among them. I want to know, if these boards can work with this version of CCS and if yes, how i ca...


TMS320C5x DOS emulator

Started by Guillaume Zin in comp.dsp13 years ago

Hello, I'm working on an old project containing TI TMS320C50 DSPs, using the very old TMS320C5x debugger for DOS version 6.50. I had a doubt...

Hello, I'm working on an old project containing TI TMS320C50 DSPs, using the very old TMS320C5x debugger for DOS version 6.50. I had a doubt on my XDS510 emulator ISA card health so I developped, based on the work of Blaise Gassend ( http://www.mit.edu/people/gassend/software/xds510/index.html ) a special version of DOSBox for Windows simulating a XDS510 card using a simple JTAG par...


F240 Flash pbs using prg2xx

Started by Lotfi in comp.dsp16 years ago 1 reply

Hi I am trying to flash a prog (im.out) between 1000h and 4000h on F240, on a Technosoft IMMF240 device which use 0-1000h flash and don't...

Hi I am trying to flash a prog (im.out) between 1000h and 4000h on F240, on a Technosoft IMMF240 device which use 0-1000h flash and don't want to overwrite that zone. My CMD is ok, because I can flash using technosoft prog via Serial... But I want to use JTAG interface and the prg2xx prog the test is fine but the writing gives errors : API Error 109, Processor Timeout OTIS Error 0...


For sale: PADK - C6727 Professional Audio Development Kit

Started by jmascini in comp.dsp9 years ago

Hi, I have an hardly used Lyrtech PADK for sale. Also have a XDS510 USB JTAG interface that goes with it. For more info on the PADK...

Hi, I have an hardly used Lyrtech PADK for sale. Also have a XDS510 USB JTAG interface that goes with it. For more info on the PADK see: http://focus.ti.com/docs/toolsw/folders/print/tmdspdk6727.html and http://www.lyrtech.com/Products/PADK.php It's a great Development kit with all possible audio and digital interfaces included (24-bit four-channel ADCs (2×) and DACs (2×) up to 192 kHz, Co...


File IO functions in DSP simulation

Started by liqi...@gmail.com in comp.dsp12 years ago

It is amazing that the file IO subroutines still work in DSP simulation even in JTAG emulation. But when my programme becomes large, it seems...

It is amazing that the file IO subroutines still work in DSP simulation even in JTAG emulation. But when my programme becomes large, it seems that fread and fwrite functions have some problems. Sometimes, fread can not read data from the file locating at the PC side, and sometimes fwrite can not write data into the file. Can anyone tell me what happens when I call fread and fwrite functions...


Tigersharc TS203 and visualDSP 4 issue

Started by jerome0613 in comp.dsp13 years ago 3 replies

Hello I'm having some problems to make my code running on 2 x TS203 rev 1.2 and VisualDSP 4.0. My small code toggles FLAG0 output pin, here are...

Hello I'm having some problems to make my code running on 2 x TS203 rev 1.2 and VisualDSP 4.0. My small code toggles FLAG0 output pin, here are my results : 1- When simulating using TS203 : OK : I can see register FLAGREG toggling according to the code. 2- When running on TS201 eval board with the same code (via JTAG) : OK : I can see both register FLAGREG and FLAG0 pin toggling according ...


DSP/BIOS : IDL Thread : CPU Usage

Started by seb in comp.dsp14 years ago 1 reply

Hello, I writing an application using the full TI kit : Code composer studio, DSP/BIOS,... and i need to know the CPU usage. The TI's...

Hello, I writing an application using the full TI kit : Code composer studio, DSP/BIOS,... and i need to know the CPU usage. The TI's DSP/BIOS include an IDL thread which can be used to see CPU usage using RTDX (jtag, debugger...). But the application i made run on a proprety acquisition board. So the idea is to uses this IDL thread in order to monitor the CPU usage. Unfortunatly, the T...


VisualDSP, HEX op-codes from LDR file

Started by DB in comp.dsp16 years ago 2 replies

Hello everybody, I would like to post-proccess output LDR file that contains description of my program (and hex code as well). This...

Hello everybody, I would like to post-proccess output LDR file that contains description of my program (and hex code as well). This post-proccessed file will be used by VisualDSP to FILL L2 memory space of BF535, or by JTAG debugger to fill external memory (SDRAM). Since LDR file stores HEX op-codes as they are (Intel HEX-32 format), and memory FILL command uses little endian format, thing...