DSP56858EVM

Started by aljmx in Freescale DSPs15 years ago 4 replies

Hello all of you, I'm new in using MOTOROLA DSPS, so i'd like to get a DSP56858EVM or 52EVM but I don't know who can sell me taht...

Hello all of you, I'm new in using MOTOROLA DSPS, so i'd like to get a DSP56858EVM or 52EVM but I don't know who can sell me taht modules here in Mexico City, so, if someone knows where i've to go tell me. Thank you...


IIR filter usage with DSP56858EVM

Started by rwolfbrandt in Freescale DSPs17 years ago 2 replies

Hello, I am new to the group as well as to the Motorola DSP56858EVM. I am trying to implement a simple IIR filter, but it is...

Hello, I am new to the group as well as to the Motorola DSP56858EVM. I am trying to implement a simple IIR filter, but it is not working properly (i.e. the cutoff frequency is not where it is supposed to be). If someone could help I would very much appreciate it and hope


DSP56858EVM Codec

Started by Kenneth Ciszewski in Freescale DSPs15 years ago

OK. I have the codec running both at the independent and dependent level on a DSP56858EVM. I am really looking to strip this driver ...

OK. I have the codec running both at the independent and dependent level on a DSP56858EVM. I am really looking to strip this driver down to a two sample depth (one left channel and one right channel) per interrupt frame. I'm not sure about how to do this. Any suggestions?


DSP56858EVM bootloading

Started by gen_mak in Freescale DSPs15 years ago

Hi, How do I go about programing the DSP56858EVM board so that I can run a program without using the metroworks debugger? i've...

Hi, How do I go about programing the DSP56858EVM board so that I can run a program without using the metroworks debugger? i've managed to make a .s file but don't know how to get it on the board. I believe i have to program the flash memory somehow and then get it to boot from


CCS: Cable disconneted, codewarrior and dsp56858evm

Started by craxy_m in Freescale DSPs12 years ago 1 reply

We have been trying to connect the dsp56858evm to the computer using codewarrioir via a parallel port cable. We are continuously receiving...

We have been trying to connect the dsp56858evm to the computer using codewarrioir via a parallel port cable. We are continuously receiving the following error: CCS: Cable disconneted. We tried configuring the CCS to 0x378 instead of lpt1 as advised by someone, but that resulted in another error: CCS: Uknown protocol CCS: Invalid parameter The parallel port of the computer i...


DSP56858EVM - Can't get SPI boot to work.

Started by Louis Loving in Freescale DSPs16 years ago 3 replies

DSP56858EVM - Can't get SPI boot to work. Hello all, I am trying to execute the Second Stage SPI Bootloader Demo...

DSP56858EVM - Can't get SPI boot to work. Hello all, I am trying to execute the Second Stage SPI Bootloader Demo in the SDK using a D


Info on Codewarrior USB Tap

Started by hgid...@instantel.com in Freescale DSPs14 years ago 2 replies

Hello: I am looking for a connection to a Freescale 56858 that will work with Codewarrior?s debugger. Currently we are talking to the...

Hello: I am looking for a connection to a Freescale 56858 that will work with Codewarrior?s debugger. Currently we are talking to the DSP56858EVM through its parallel port interface and would like faster download times. Eventually we will need to talk to our own board. Thanks.


ElectricalFeaturesEVM56858

Started by Jean Adame in Freescale DSPs16 years ago 1 reply

Hi all, I?m develping an audio aplicattion using the DSP56858EVM, now I want to connect an amplifier at the line-in of the EVM...

Hi all, I?m develping an audio aplicattion using the DSP56858EVM, now I want to connect an amplifier at the line-in of the EVM to work with voice signals from a microphone. What I need is to know the information about the electrical characteristics of this or where I can


Clock frequency

Started by Vishal sen Gupta in Freescale DSPs17 years ago 1 reply

I guess the operating clock frequency for DSP56858EVM by default is 120MHz. If yes, Can it be increased more than 120Mhz? If no, how...

I guess the operating clock frequency for DSP56858EVM by default is 120MHz. If yes, Can it be increased more than 120Mhz? If no, how can it be operated at maximum frequency available?


DSP56858EVM, CW6.0 & SDK2.0E

Started by thisalfkatz in Freescale DSPs15 years ago 1 reply

Have just received my EVM, copy of CW6.0 (patched to 6.0.1) and SDK2.0E. Following th instructions in the targetting manual, I get ...

Have just received my EVM, copy of CW6.0 (patched to 6.0.1) and SDK2.0E. Following th instructions in the targetting manual, I get to 1.2.4 Step 3 (execute a buildall on the SDK). Now I get loads of errors (e.g. multiply defined symbols), and then the build grinds to a halt compilein


56858 second stage serial bootloader

Started by ian...@glensound.co.uk in Freescale DSPs10 years ago

Hello, I have been trying to get the second stage SPI serial bootloader to work on the DSP56858EVM using the example from Precessor...

Hello, I have been trying to get the second stage SPI serial bootloader to work on the DSP56858EVM using the example from Precessor Expert. After much hair pulling it looks as if the second stage bootloader is loaded and runs but fails to load my application code. The SecondStageSPIBootLoader.pdf document says that the application code should be in s-record format at 0x1C00 in the flash. ...


codec example in Embedded SDK for DSP56800E

Started by Vishal sen Gupta in Freescale DSPs17 years ago

hi I have installed the embedded sdk along with dSP56858EVM. I opened the codec.mcp project. I was able to build the project...

hi I have installed the embedded sdk along with dSP56858EVM. I opened the codec.mcp project. I was able to build the project sucessfully but didn't find the debug and run menu items highlighted. I fould the linker was chosen as none. I changed the linker in target