56F805 EVM

Started by ESubbu in Freescale DSPs16 years ago

Does anybody gives me details of where will I get the DSP 56F805 module immediately.. Thanks, esubbu

Does anybody gives me details of where will I get the DSP 56F805 module immediately.. Thanks, esubbu


EVM for 56801 - where to buy?

Started by Stefan Stenzel in Freescale DSPs16 years ago 1 reply

Hello, Subject says it all, where can I get one of these in germany? Would also consider 803/805/807 types, I just need 6ch...

Hello, Subject says it all, where can I get one of these in germany? Would also consider 803/805/807 types, I just need 6ch ADC,SPI and some Flash. Thanks, Stefan


RE: Motorola DSP comparison

Started by Roelof Oelofsen in Freescale DSPs18 years ago

Hi, Thanks for all the response. I actually did the whole thing the wrong way round! I first bought the 56f807evm with license,...

Hi, Thanks for all the response. I actually did the whole thing the wrong way round! I first bought the 56f807evm with license, and then I asked your opinions. I have only been working with the evm for 2 days now (I am not familiar with Codewarrior, the assistance


DSP56F805EVM rs232

Started by yurubutugralb in Freescale DSPs14 years ago

The evaluation board has RTS connected to CTS. I am using an MSComm ActiveX control to talk to EVM. All is well. The production item...

The evaluation board has RTS connected to CTS. I am using an MSComm ActiveX control to talk to EVM. All is well. The production item will use SCI0, with RTS and CTS represented at GPIO D. I am at a loss for how to emulate this loop-back in software! Thanks


DSP56805 EVM time out on SCI

Started by Manfred Plagmann in Freescale DSPs16 years ago

Hi, I am operating the serial port in blocked mode and wonder if it is possible to set a timeout for this mode of operation? I...

Hi, I am operating the serial port in blocked mode and wonder if it is possible to set a timeout for this mode of operation? I would like the program to resume if no data has arrived for more than say 2 seconds. Many thanks. Manfred


Question about SDK programming.

Started by ritu_eshar in Freescale DSPs17 years ago 1 reply

Hi All, Presently am working with 56807 EVM using codewarrior, but am programming strictly in C. I collected the following...

Hi All, Presently am working with 56807 EVM using codewarrior, but am programming strictly in C. I collected the following example, which functions such that when a timer is fed with an input via the function generator, the GPIO_B_PIN_7 follows suit. I.E. the risi


CAN TX PROBLEM WITH 56F83232EVM

Started by simo...@hotmail.com in Freescale DSPs13 years ago 2 replies

Hi to everybody, I'm a young electronical engeneer and i'm using for the first time an EVM with 56f83232. I try to configure the flexcan...

Hi to everybody, I'm a young electronical engeneer and i'm using for the first time an EVM with 56f83232. I try to configure the flexcan module following the instrustion on the chapter 7 of the 56f8300 peripheral user manual and i also have an example bean to help me in the initialization. My CAN1_Init() function is : void CAN1_Init() { setRegBit(FCMCR, SOFT_RST); /* Soft-res...


Crystal not working

Started by dibosco in Freescale DSPs16 years ago 6 replies

Hi folks, I've just built up my new target board (first one with a 56Fxxx) and am having no joy getting the crystal going -...

Hi folks, I've just built up my new target board (first one with a 56Fxxx) and am having no joy getting the crystal going - which is a bit depressing! I've got a 56F803, with an ACT crystal and 10M across the crystal, just as the manual suggests and the EVM has.


RE: Matlab to Motorola conversion

Started by jeffrey_2211 in Freescale DSPs17 years ago

Hi fellows, I have done a speech processing project using MATLAB. Is there any means of porting the code to MOTOROLA DSP56002...

Hi fellows, I have done a speech processing project using MATLAB. Is there any means of porting the code to MOTOROLA DSP56002 EVM ? Bye


CCI error

Started by gyps...@hotmail.com in Freescale DSPs13 years ago

Hello, We are new to the dsp 56858EVM we have been trying to load a code (not specific) to start working on the EVM but the problem we are...

Hello, We are new to the dsp 56858EVM we have been trying to load a code (not specific) to start working on the EVM but the problem we are facing is the eeror that accurs everytime at the debugging stage ie [CCI cable disconnected] . Believe it or not we have tried every solution that we could think of. Probably there is a problem with the cable, we would be more than thankful if anyone ca...


downloading to flash

Started by VRISHABHADEVA JWALLANA in Freescale DSPs18 years ago

hello, 1.In EVM56805 if I disable the external ram no program works. 2.I have designed card using DSP56805 to which i am ...

hello, 1.In EVM56805 if I disable the external ram no program works. 2.I have designed card using DSP56805 to which i am not able to download my program . I am using code warrior for downloading (through parallel to jtag converter according to EVM schematics)


DSP56858-VoIP

Started by dsp_devil in Freescale DSPs16 years ago 3 replies

I just bought a Motorola 56858 EVM and along with it came the Codewarrior software. I'm trying to implement a VoIP system. However, ...

I just bought a Motorola 56858 EVM and along with it came the Codewarrior software. I'm trying to implement a VoIP system. However, i have not had any prior experience with either the hardware or software. Can anyone give some advice as to a good place to start on such a project. Are


ADC usage

Started by sowmya_gk in Freescale DSPs15 years ago 2 replies

Respected Sir/Madam, we are working on a project which has 56f805 DSP on the EVM kit. we're new to embedded field. we have a...

Respected Sir/Madam, we are working on a project which has 56f805 DSP on the EVM kit. we're new to embedded field. we have a few queries which need to be cleared to start our project. kindly help us by doing the need. The queries are as follows: 1. A basic sample p


FIR FILTER for the Motorola DSP56F826EVM

Started by dceinatel in Freescale DSPs15 years ago 1 reply

Does anybody have (or know where to get) a FIR filter (audio filter) example for the DSP56F826EVM. I used to work with the...

Does anybody have (or know where to get) a FIR filter (audio filter) example for the DSP56F826EVM. I used to work with the DSP56002EVM but now i have this new EVM and need to learn many things again. I would appreciate if someone can help me. Thank you. Daniel C


Using DSPCOMMPARALLEL

Started by Lionel Degoutte in Freescale DSPs16 years ago 2 replies

I have The evaluation board DSP56F807 EVM-1 with codewarrior 5.0. The communication between the computer and the evaluation board is...

I have The evaluation board DSP56F807 EVM-1 with codewarrior 5.0. The communication between the computer and the evaluation board is very slow when I want to run or stop the program. Moreover I can put only on breakpoint in the program. Can someone tell me if there is the same limita


JTAG "Cannot connect to Board"

Started by yurubutugralb in Freescale DSPs14 years ago 2 replies

Hello all, Using CodeWarrior? Development Studio for Motorola DSP56800 version 5.1 targeting the DSP56F805 chip and using Macraigor...

Hello all, Using CodeWarrior? Development Studio for Motorola DSP56800 version 5.1 targeting the DSP56F805 chip and using Macraigor Wiggler for JTAG. I can download to the EVM but not to my project board. Something changed because I used to be able to do both. Please point me to what levels, waveforms to look for in troubleshooting.


PC - DSP56303EVM interface

Started by GuillaumeDesj in Freescale DSPs16 years ago

Hi, I was recently looking into setting up a serial interface between a PC and the EVM board, in order to transfer data...

Hi, I was recently looking into setting up a serial interface between a PC and the EVM board, in order to transfer data generated by a PC application to the DSP. However, the DSP56303 datasheet tells me that the minimum clock speed that the SCI interface can handl


Local variable declaration

Started by hyzhou_14850 in Freescale DSPs17 years ago 1 reply

Hi, everyone: I am experiencing a strange problem with my DSP56803EVM and CodeWarrior 5. My application talks to a PC...

Hi, everyone: I am experiencing a strange problem with my DSP56803EVM and CodeWarrior 5. My application talks to a PC through the EVM??s serial port and the user LED toggles if the 1ms interrupt works fine. The communication was OK when the CodeWarrior target sett


807 SCI1/GPIOD problems

Started by BJ Opp in Freescale DSPs16 years ago

I'm trying to setup SCI1 as a communications port (using the DSP56f807 EVM), but am running into difficulty with it. I have ...

I'm trying to setup SCI1 as a communications port (using the DSP56f807 EVM), but am running into difficulty with it. I have already setup SCI0 and verified it to be working so I know that i'm on the right track for sampling data. I have initialized both ports the same way, 9600 baud,


Re: Evaluation boards UK availability

Started by David in Freescale DSPs16 years ago 2 replies

The 56002EVM is long gone. The SRAM that was on them went obsolete and the board never got redesigned to use something else. And,...

The 56002EVM is long gone. The SRAM that was on them went obsolete and the board never got redesigned to use something else. And, the 56002 device itself has also gone obsolete. The audio EVM is expensive because it accomodates the entire Motorola audio DSP product line on dau