PCMaster doesn't stop quitting

Started by Bruno Tremblay in Freescale DSPs15 years ago

Hi, I try to work with PCMaster. If I just use the watch-grid with or without plain HTML in the control page, PCMaster work...

Hi, I try to work with PCMaster. If I just use the watch-grid with or without plain HTML in the control page, PCMaster work fine. But if I try to display a variable in the control page, PCMaster doesn't stop quitting everytime I navigate in the project tree or resize the windo


PCMaster bug

Started by Bende Georg in Freescale DSPs16 years ago

Hello, Does anyone meet the following bug in PCMaster: If I use a bitfield with one-bit sized variables, and I change one bit...

Hello, Does anyone meet the following bug in PCMaster: If I use a bitfield with one-bit sized variables, and I change one bit in the field, sometimes (not always, about once in 4 times) all the bits on the right side are zeroed out. My PCMaster version is 1.2.0.11, if anyone h


Connecting the pcmaster software

Started by atid2 in Freescale DSPs17 years ago 3 replies

Hi all, I'm trying to connect to my 56F827EVM board using the pcmaster, but I seem to get the following error message when...

Hi all, I'm trying to connect to my 56F827EVM board using the pcmaster, but I seem to get the following error message when running the pcmaster: "Cannot detect the board information ! The communication will be paused." I'm connected to the board using RS232 ser


Combined PCMaster and SCI useage.

Started by cmafatcontroller in Freescale DSPs16 years ago

I am about to try setting up a SDK based program where I use both PCMaster and SCI comms to a display on an 803 (has only 1 SCI...

I am about to try setting up a SDK based program where I use both PCMaster and SCI comms to a display on an 803 (has only 1 SCI port). I want to set it up whereby on powerup/ reset the programme checks the state of a GPIO pin, and then determines whether to enable PCMaster or SCI.


Using the 86F8xx SDK PCMaster ActiveX with JavaScript

Started by Roberts, Drew in Freescale DSPs18 years ago

Using the 86F8xx SDK PCMaster ActiveX with JavaScript I'm trying to implement a demo using the pcmaster and an DSP86F807 eval...

Using the 86F8xx SDK PCMaster ActiveX with JavaScript I'm trying to implement a demo using the pcmaster and an DSP86F807 eval board. I have implemented part of the demo using VBScript, but I need to change to JavaScr


PCMaster problem

Started by in Freescale DSPs13 years ago 3 replies

Hi all, I?m programming the 56F803 and I?m using PCMaster to see the DSP?s variables, but there's a problem: most time, the DSP doesn't...

Hi all, I?m programming the 56F803 and I?m using PCMaster to see the DSP?s variables, but there's a problem: most time, the DSP doesn't transmit anything (I saw that in the oscilloscope). Can somebody help me? Thanks a lot. Francisco S.


pc master crash

Started by Anonymous in Freescale DSPs15 years ago 1 reply

hi, I'm using PC Master (by Motorola) on windows 98 to communicate with a DSP 56F807. When I change panel in PCMaster from...

hi, I'm using PC Master (by Motorola) on windows 98 to communicate with a DSP 56F807. When I change panel in PCMaster from the tree, the programm's crashing and the serial port leaves opened. So I need to restart PC to reopen the PCMaster Project. When I'm using a


AW: PCMaster Baud rate

Started by Bende Georg in Freescale DSPs15 years ago

The maximum speed I was able to use PCMaster was 38400, but in this case the routine was called every 300 microseconds....

The maximum speed I was able to use PCMaster was 38400, but in this case the routine was called every 300 microseconds. Alternatively you can make it interrupt-driven but don't expect too much speed increase because it's pretty tough to process commands and assemble the packets on that spe


.elf.s and .elf files

Started by max_mont in Freescale DSPs16 years ago

Hi, I'm developing an application on PC commnicating with DSP to remplace PCMaster. I'd like to be sure that symbol file...

Hi, I'm developing an application on PC commnicating with DSP to remplace PCMaster. I'd like to be sure that symbol file (.elf) corresponds to the programm in DSP (.elf.S file). That's implemented in PCMaster : when I connect and the elf file in not the good one, P


PCMaster Baud rate

Started by cmafatcontroller in Freescale DSPs15 years ago

I want to up the PCMaster Baud rate from 9600 as it has been supplied. I have found the Baud rate configuration in pmasterdrv.c...

I want to up the PCMaster Baud rate from 9600 as it has been supplied. I have found the Baud rate configuration in pmasterdrv.c in the BSP directory of SDK, and changed it to every standard increment between 9600 and 57600 - e.g. 19200, 38400 etc. I also changed the baud rate


PC Master

Started by Roger Flor in Freescale DSPs17 years ago 2 replies

Hello! Has anybody used the PCMaster application? How does one set the board time using #define PC_MASTER_RECORDER_TIME_BASE ...

Hello! Has anybody used the PCMaster application? How does one set the board time using #define PC_MASTER_RECORDER_TIME_BASE in appconfig.h? Thanks Roger


PC Master with PE?

Started by tomppi01 in Freescale DSPs15 years ago 1 reply

Hi, Does anybody know how to set up the PCMaster with PE and CW6.1? My application stops every time I start the PC Master. ...

Hi, Does anybody know how to set up the PCMaster with PE and CW6.1? My application stops every time I start the PC Master. I get the message: Scope error. Please write if you have an idea. Tamas


Re: Modem Interface to DSP 56807

Started by naidoorn1 in Freescale DSPs16 years ago

Hi, I need to be able to use pcmaster on my desktop to remotely view data that is stored in flash memory of a 56807. The DSP...

Hi, I need to be able to use pcmaster on my desktop to remotely view data that is stored in flash memory of a 56807. The DSP and my desktop pc are each connected to modems. Can anyone please tell me how I should go about this. Any help will be appreciated!


Some problems with FreeMaster and MC56F8345

Started by Bruno Tremblay in Freescale DSPs14 years ago 3 replies

Hi, I have two problems with FreeMaster (new name for PCMaster). The first one, I try to access the ADCA registers in the...

Hi, I have two problems with FreeMaster (new name for PCMaster). The first one, I try to access the ADCA registers in the variable watch section of FreeMaster by setting address's variable to 0xF200. The value returned is 0xFFFF. I should see at least the initialization value. Does somebody know any solution for a direct read of a reg


rfft output

Started by li_xinming in Freescale DSPs16 years ago 1 reply

I am practicing rfft using EVM56807. I know the output is pZ, however, the question is how to get Real Part and Imag Part to ...

I am practicing rfft using EVM56807. I know the output is pZ, however, the question is how to get Real Part and Imag Part to calculate PSD. Furthermore, if showing the result by PCmaster, considering data transmition rate, what' s the largest samples can be done by continuous rfft? A


PCMaster and 56F8345

Started by Bruno Tremblay in Freescale DSPs14 years ago

Hi,  

Hi,