A/d sdk driver for 56f807 question

Started by Roelof Oelofsen in Freescale DSPs17 years ago 1 reply

Hi group, I just started to explore the A/D SDK driver for the 56f807. My question is this: If I set the A/D up in loop...

Hi group, I just started to explore the A/D SDK driver for the 56f807. My question is this: If I set the A/D up in loop sequential mode, the conversion complete interrupt will be disabled. In the header file the auther states that I must use the ADC_STATE_READ ADC ioctl


Using SDK'd RFFT and RIFFT for Filtering

Started by vo1hl in Freescale DSPs16 years ago

Hi Everyone! I am using SDK 2.4.1 with CW 4 on a DSP56F826 platform without external memory. I have written a program that...

Hi Everyone! I am using SDK 2.4.1 with CW 4 on a DSP56F826 platform without external memory. I have written a program that sucks in a 128 sample vector at a sample rate of 8000 sps, submits this to dfr16RFFT then takes the resulting dfr16_tInplace vector and submits it to


GPIO Macro

Started by Jacob Christ in Freescale DSPs17 years ago 2 replies

Does anyone know the official channel for SDK feature enhancment? I added the following macro to help with initalization of my...

Does anyone know the official channel for SDK feature enhancment? I added the following macro to help with initalization of my gpio port a port at a time... Its a variant of the gpioPin macro it would might be a reasonable addition to the SDK. #define gpioPort(Port) (((


RE: Need CD installation key for Emb. SDK 2.3.5 ( n o more on the web)

Started by Johnson, Jerry in Freescale DSPs18 years ago

I used 4755434B55. This worked for many earlier versions! -----Original Message----- From: sademade [mailto:] Sent:...

I used 4755434B55. This worked for many earlier versions! -----Original Message----- From: sademade [mailto:] Sent: Thursday, February 07, 2002 11:12 PM To: Subject: [motoroladsp] Need CD installation key for Emb. SDK 2.3.5 ( no more on the web)


flashing with jtag and SDK tools

Started by max_mont in Freescale DSPs16 years ago 1 reply

Hi, I'd like to flash a bootloader on the DSP (56807) with jtag and SDK tool (flash_over_jtag.exe) I take the sample for...

Hi, I'd like to flash a bootloader on the DSP (56807) with jtag and SDK tool (flash_over_jtag.exe) I take the sample for the configuration file. Must I keep all the sections to flash just the bootloader ??? Or can I delete all the sections excepted the boot


Help with a SDK application

Started by josalfe2002 in Freescale DSPs17 years ago

Hi again everyone.... I need some help. When you install the SDK cd on your machine, it install an application call "Serial App"...

Hi again everyone.... I need some help. When you install the SDK cd on your machine, it install an application call "Serial App" (it's a VB application).....when you read the help, it says you need to run on your DSP Board the serial.cld program Does anyone know


data flash without sdk

Started by Paul Dalluge in Freescale DSPs16 years ago 8 replies

HI, I am using 56801 with limited memory space and want to save constants into a certain data flash area while flash...

HI, I am using 56801 with limited memory space and want to save constants into a certain data flash area while flash programming. I am able to do it using the sdk, but unfortunately this takes up to much space. Does anyone have an example of writing to the data flash wit


RE: simple project demonstrating how to set-up inte rrupts without the use of SDK

Started by Jarrid Gross in Freescale DSPs17 years ago

I agree with Art here. Daniel sent me (last year) a proto-type project using the simple intrinsic methods for dealing with an...

I agree with Art here. Daniel sent me (last year) a proto-type project using the simple intrinsic methods for dealing with an interrupt. This is what I used for some time, without any significant problem. I had setup direct (NON SDK) vectors and handlers for 4 timers, async TX


DSP56827 Codec

Started by James Ball in Freescale DSPs17 years ago 3 replies

I?m working on a project for school and have been giving a DSP56827. I?ve installed the Motorola SDK 2.41 and have tried to run the...

I?m working on a project for school and have been giving a DSP56827. I?ve installed the Motorola SDK 2.41 and have tried to run the Codec sample project that came with the SDK through CodeWarrior, but it will not work. I have probed all the data lines around the codec (clock, sync and data


Motorola DSP56F807 SDK and Micro C OS integration problem.

Started by Srinivas in Freescale DSPs17 years ago

Hi, I am using motrola DSP56F807 SDK 2.5 and Micro c OS 2.6 Version. I have a task X waiting on event E. The event E is...

Hi, I am using motrola DSP56F807 SDK 2.5 and Micro c OS 2.6 Version. I have a task X waiting on event E. The event E is set in the CanReadCallBack function which is being called by the CANReceiveSuperISR. The event is being set in ISR context.


Linker Error without SDK

Started by arcanebusa in Freescale DSPs16 years ago

Hello, I'm in the process of re-writing my application without the SDK, and am getting a linker error: Link Error :...

Hello, I'm in the process of re-writing my application without the SDK, and am getting a linker error: Link Error : Undefined : "ARTDIVS32UZ" Referenced from "FInterp" in main.c Here's the offending code: ushort Interp(int X


SDK tf16SinPIx

Started by Jacob Christ in Freescale DSPs17 years ago 2 replies

Today I noticed that the Motorola SDK tf16SinPIx() returns unexpected values for the following: tf16SinPIx(0x4000) = 0x8000 //...

Today I noticed that the Motorola SDK tf16SinPIx() returns unexpected values for the following: tf16SinPIx(0x4000) = 0x8000 // expected 0x7fff tf16SinPIx(0x8000) = 0xc5a8 // expected 0x0000 Any one else have similar results? Also, all other values seem to work fin


codec example in Embedded SDK for DSP56800E

Started by Vishal sen Gupta in Freescale DSPs17 years ago

hi I have installed the embedded sdk along with dSP56858EVM. I opened the codec.mcp project. I was able to build the project...

hi I have installed the embedded sdk along with dSP56858EVM. I opened the codec.mcp project. I was able to build the project sucessfully but didn't find the debug and run menu items highlighted. I fould the linker was chosen as none. I changed the linker in target


SDK SPI compile error

Started by Corey, Rick in Freescale DSPs17 years ago 1 reply

Hi I'm trying to use the SDK to configure a 56F803 SPI peripheral. I start with #define INCLUDE_SPI in appconfig.h. (I already...

Hi I'm trying to use the SDK to configure a 56F803 SPI peripheral. I start with #define INCLUDE_SPI in appconfig.h. (I already have #define INCLUDE_IO.) As soon as I #define INCLUDE_SPI, I get the following compile error: (I'm using 5.0.4). I haven't written


Motorola Premier SDK Part Number...

Started by Jacob Christ in Freescale DSPs17 years ago 3 replies

Does anyone know the part number for the Motorola Premier SDK. Motorola Tech Support doesn't but I figured someone here would. ...

Does anyone know the part number for the Motorola Premier SDK. Motorola Tech Support doesn't but I figured someone here would. Jacob


data flash programming without sdk routines

Started by jmgarcia005 in Freescale DSPs16 years ago 1 reply

Hi, i'm new in this list. I'm working now in data flash programming. Can anybody send me (Fabio's) routines for data flash...

Hi, i'm new in this list. I'm working now in data flash programming. Can anybody send me (Fabio's) routines for data flash programming without sdk please? Thanks in advance. Jos? Miguel Garc?a


AW: 56800 SDK CAN driver

Started by Bende Georg in Freescale DSPs16 years ago

Hello, If you are planning tu buy a CanOpen stack, then it has mostly some kind of basic self-made SDK. I know about 3...

Hello, If you are planning tu buy a CanOpen stack, then it has mostly some kind of basic self-made SDK. I know about 3 companies offering it for 56f80x: -Port (www.port.de) -Vector Informatik (www.vector-informatik.de) -Ixxat (www.ixxat.de) Best wishes,


Access Path problem for any newly created project.

Started by Nitin Madhukar Yewale in Freescale DSPs17 years ago 2 replies

Hi, I have installed Codewarrior and SDK on C: drive and I am creating new projects on D: drive. I got following errors after...

Hi, I have installed Codewarrior and SDK on C: drive and I am creating new projects on D: drive. I got following errors after compilation of newly created project [827 using SDK] it gives error like "Could not find or load the file "dspfunc.lib" for target


Need help with Host Port Bootloader for the MotDSP56858

Started by Shahed Rahim in Freescale DSPs15 years ago 2 replies

Hi, I have written a 2nd stage bootloader for the Host Port Interface using polling method. And I have tested that it seems to...

Hi, I have written a 2nd stage bootloader for the Host Port Interface using polling method. And I have tested that it seems to work with the 1st stage bootloader tester supplied with the Motorola SDK. But, if I try to boot directly into the hardware without the SDK 1st stage b


Embedded SDK DSP Function Library Preformance Section

Started by Jacob Christ in Freescale DSPs17 years ago 3 replies

In the Embedded SDK DSP Function Library Preformance Section (12.3) there are charts showing the instruction cycles for a particular...

In the Embedded SDK DSP Function Library Preformance Section (12.3) there are charts showing the instruction cycles for a particular function. Many of these tables have colums labled AS, BFP, and NS. For the life of me, I can't figure out what these mean. I have searched up and down