Reply by Vladimir Vassilevsky●October 2, 20082008-10-02
Roman Rumian wrote:
> Hi Vladimir,
>
> Vladimir Vassilevsky pisze:
> (...)
>
>> CS42436 is not a high end codec, it is a consumer quality part.
> and what is your opinion about CS5364/6/8 multichannel A/D converters
> (also TI PCM420x) ?
The magic number is the dynamic range of 120dB or higher. PCM42xx fits
this requirement. Very careful attention should be paid to the
schematics and the layout.
> Have you used them or know a professional audio device based on these
> devices ?
Many audio folks prefer AKM parts. This is the area of beliefs, and the
AKM has the widespread reputation of the unbeatable performance.
Vladimir Vassilevsky
DSP and Mixed Signal Design Consultant
http://www.abvolt.com
Reply by Roman Rumian●October 1, 20082008-10-01
Hi Vladimir,
Vladimir Vassilevsky pisze:
(...)
> I guess I know, since I design them :-)
> CS42436 is not a high end codec, it is a consumer quality part.
> The performance designs use the external front/back end amplifiers if
> the gain matching is required.
and what is your opinion about CS5364/6/8 multichannel A/D converters
(also TI PCM420x) ?
Have you used them or know a professional audio device based on these
devices ?
Kind regards
Roman
Reply by Vladimir Vassilevsky●September 29, 20082008-09-29
Roman Rumian wrote:
> Vladimir Vassilevsky pisze:
> (...)
>
>> I used CS42438 a lot. My advice would be never use any built in
>> features of the codec; do all controls either by DSP or by the
>> external hardware.
>
>
> thanks Vladimir. :-)
>
> It is too late to throw up internal PGA.
Then you have to reconcile to the performance level you that you are
getting. BTW, check the codec errata sheets also; there are few nasty
bugs with the built in features.
> Probably, most of high end multichannel audio devices use stereo codecs
> or even A/D converters only. Do you know how they are designed ?
I guess I know, since I design them :-)
CS42436 is not a high end codec, it is a consumer quality part.
The performance designs use the external front/back end amplifiers if
the gain matching is required.
Vladimir Vassilevsky
DSP and Mixed Signal Design Consultant
http://www.abvolt.com
Reply by Roman Rumian●September 29, 20082008-09-29
Vladimir Vassilevsky pisze:
(...)
> I used CS42438 a lot. My advice would be never use any built in
> features of the codec; do all controls either by DSP or by the external
> hardware.
thanks Vladimir. :-)
It is too late to throw up internal PGA.
Probably, most of high end multichannel audio devices use stereo codecs
or even A/D converters only. Do you know how they are designed ?
Kind regards
Roman Rumian
Reply by Vladimir Vassilevsky●September 29, 20082008-09-29
Roman Rumian wrote:
> Hello,
>
> in a multichannel audio mixer I use two CS42436 codecs. Input and
> outputs are differential.
> When the input PGA is set to more than +12dB then a audible level of
> white noise can be heard at the outputs (codec is passing through input
> signals). Shorting inputs does not change this situation.
>
> Technical support has not sent the answer for more than one week (they
> promise to give one in a three days), so maybe you can help me ?
I used CS42438 a lot. My advice would be never use any built in
features of the codec; do all controls either by DSP or by the external
hardware.
Vladimir Vassilevsky
DSP and Mixed Signal Design Consultant
http://www.abvolt.com
Reply by Roman Rumian●September 29, 20082008-09-29
Hello,
in a multichannel audio mixer I use two CS42436 codecs. Input and
outputs are differential.
When the input PGA is set to more than +12dB then a audible level of
white noise can be heard at the outputs (codec is passing through input
signals). Shorting inputs does not change this situation.
Technical support has not sent the answer for more than one week (they
promise to give one in a three days), so maybe you can help me ?
Regards
Roman Rumian