Reply by Michael Dunn April 4, 20082008-04-04
Asif,

On 4/4/08, asif bagwan wrote:
>
> hellow,
> my 16x2 LCD pin config is
> Pin[7:14]a pins
DC_D0 - DC_D7

pin 4,5,6=Register select,
DC_A2

R/W,
>

DC_AWE#

EN respt
DC_CE2#

piin 1 & 16 GND and 2 and 15 +VCC
You will need to furnish +15v externally.

now hoe to connect this control and data pins on GPIO pins of HPI
> port HD[0:15]
You should use the external memory interface [J4] and not the HPI, if
possible. This will allow you to directly read and write from/to the device
in C. If you must use the HPI port, it only has 10 GPIO pins. You can tie
the enable to be true at all times, allowing you to interface with 10
signals. You can choose to connect them in any way that you like. To make
the sw easier, connect GPIO15 to data 7, GPIO14 to data 6, etc. The
remaining 2 will not matter how you connect them. You will then have to
create the write strobe with your sw.

mikedunn
this are my specs plz tell me how to connect lCD
> ASIFBAGWAN
>
> ----- Original Message ----
> From: Michael Dunn
> To: asif bagwan
> Cc: DSPgroup
> Sent: Thursday, April 3, 2008 7:24:59 AM
> Subject: Re: [c6x] 16x2 LCD display interfacing to GPIO
>
> Asif,
>
> On 4/3/08, asif bagwan >
> wrote:
> >
> > if i interface lcd (16x2 ) to HPI port then which connector should
> > used and how to configure it
> > Do you remeber my previous question??
> There is more than one interface for '16x2 LC Display'. Could you identify
> the specs for your interface??
>
> It is a bit difficult to identify pins if one does not know how many that
> you need [and for what].
>
> Please post your request to the group [not directly to me] - you probably
> cannot afford my personal services.
>
> mikedunn
> > ASIFBAGWAN
> >
> > ----- Original Message ----
> > From: Michael Dunn >
> > To: asif bagwan >
> > Cc: c6x@yahoogroups. com
> > Sent: Tuesday, April 1, 2008 4:40:47 AM
> > Subject: Re: [c6x] 16x2 LCD display interfacing to GPIO
> >
> > asif,
> >
> > On 4/1/08, asif bagwan >
> > wrote:
> > >
> > >
> > > hi all,
> > > I want to interface 16x2 LCD display to gpio pins of tms320c6713 dsp
> > > kit
> > > so assist me where to conncet lcd and how to confogure it.
> > > thank you
> > >
> > >
> > There is more than one interface for '16x2 LC Display'. Could you
> > identify the specs for your interface??
> >
> > mikedunn
> >
> > -in advance
> > >
> > > ASIF BAGWAN
> > >
> > > ------------------------------
> > > Special deal for Yahoo! users friends - No Cost. Get a month of
> > > Blockbuster Total Accessnow
> > >
> > >
> >
> >
> > --
> > www.dsprelated. com/blogs- 1/nf/Mike_ Dunn.php
> >
> >
> >
> >
> > ------------------------------
> > You rock. That's why Blockbuster's offering you one month of Blockbuster
> > Total Access,
> > No Cost.
> > --
> www.dsprelated. com/blogs- 1/nf/Mike_ Dunn.php
> ------------------------------
> You rock. That's why Blockbuster's offering you one month of Blockbuster
> Total Access,
> No Cost.
>

--
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
Reply by asif bagwan April 4, 20082008-04-04
hellow,
my 16x2 LCD pin config is
Pin[7:14]a pins
pin 4,5,6=Register select, R/W, EN respt
piin 1 & 16 GND and 2 and 15 +VCC
now hoe to connect this control and data pins on GPIO pins of HPI port HD[0:15]
this are my specs plz tell me how to connect lCD

ASIFBAGWAN

----- Original Message ----
From: Michael Dunn
To: asif bagwan
Cc: DSPgroup
Sent: Thursday, April 3, 2008 7:24:59 AM
Subject: Re: [c6x] 16x2 LCD display interfacing to GPIO

Asif,

On 4/3/08, asif bagwan wrote:
if i interface lcd (16x2 ) to HPI port then which connector should used and how to configure it

Do you remeber my previous question??
There is more than one interface for '16x2 LC Display'. Could you identify the specs for your interface??

It is a bit difficult to identify pins if one does not know how many that you need [and for what].

Please post your request to the group [not directly to me] - you probably cannot afford my personal services.

mikedunn

ASIFBAGWAN

----- Original Message ----
From: Michael Dunn
To: asif bagwan
Cc: c6x@yahoogroups. com
Sent: Tuesday, April 1, 2008 4:40:47 AM
Subject: Re: [c6x] 16x2 LCD display interfacing to GPIO
asif,
On 4/1/08, asif bagwan wrote:

hi all,
I want to interface 16x2 LCD display to gpio pins of tms320c6713 dsp kit
so assist me where to conncet lcd and how to confogure it.
thank you

There is more than one interface for '16x2 LC Display'. Could you identify the specs for your interface??
mikedunn
-in advance

ASIF BAGWAN

Special deal for Yahoo! users friends - No Cost. Get a month of Blockbuster Total Access now

--
www.dsprelated. com/blogs- 1/nf/Mike_ Dunn.php

You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost.

--
www.dsprelated. com/blogs- 1/nf/Mike_ Dunn.php

____________________________________________________________________________________
You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost.
http://tc.deals.yahoo.com/tc/blockbuster/text5.com
Reply by Michael Dunn April 3, 20082008-04-03
Asif,

On 4/3/08, asif bagwan wrote:
>
> if i interface lcd (16x2 ) to HPI port then which connector should
> used and how to configure it
>

Do you remeber my previous question??
There is more than one interface for '16x2 LC Display'. Could you identify
the specs for your interface??

It is a bit difficult to identify pins if one does not know how many that
you need [and for what].

Please post your request to the group [not directly to me] - you probably
cannot afford my personal services.

mikedunn
> ASIFBAGWAN
>
> ----- Original Message ----
> From: Michael Dunn
> To: asif bagwan
> Cc: c...
> Sent: Tuesday, April 1, 2008 4:40:47 AM
> Subject: Re: [c6x] 16x2 LCD display interfacing to GPIO
>
> asif,
>
> On 4/1/08, asif bagwan >
> wrote:
> >
> >
> > hi all,
> > I want to interface 16x2 LCD display to gpio pins of tms320c6713 dsp kit
> >
> > so assist me where to conncet lcd and how to confogure it.
> > thank you
> >
> >
> There is more than one interface for '16x2 LC Display'. Could you identify
> the specs for your interface??
>
> mikedunn
>
> -in advance
> >
> > ASIF BAGWAN
> >
> > ------------------------------
> > Special deal for Yahoo! users friends - No Cost. Get a month of
> > Blockbuster Total Accessnow
> >
> >
> --
> www.dsprelated. com/blogs- 1/nf/Mike_ Dunn.php ------------------------------
> You rock. That's why Blockbuster's offering you one month of Blockbuster
> Total Access,
> No Cost.
>

--
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
Reply by Michael Dunn April 1, 20082008-04-01
asif,

On 4/1/08, asif bagwan wrote:
> hi all,
> I want to interface 16x2 LCD display to gpio pins of tms320c6713 dsp kit
> so assist me where to conncet lcd and how to confogure it.
> thank you
>

There is more than one interface for '16x2 LC Display'. Could you identify
the specs for your interface??

mikedunn

-in advance
>
> ASIF BAGWAN
>
> ------------------------------
> Special deal for Yahoo! users friends - No Cost. Get a month of
> Blockbuster Total Accessnow
>

--
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
Reply by asif bagwan April 1, 20082008-04-01
hi all,
I want to interface 16x2 LCD display to gpio pins of tms320c6713 dsp kit
so assist me where to conncet lcd and how to confogure it.
thank you
-in advance

ASIF BAGWAN
____________________________________________________________________________________
Special deal for Yahoo! users & friends - No Cost. Get a month of Blockbuster Total Access now
http://tc.deals.yahoo.com/tc/blockbuster/text3.com