Reply by Herry Imata Sitepu●May 12, 20032003-05-12
On Wed, 7 May 2003, prajumokeri wrote:
>
> Hi,
> I have just started with code composer & dsk5402.I am trying to
> interface an FPGA kit with dsk5402 through rs232 interface.These are
> the problems I,m facing
> 1.I can't include headerfiles such as
"type.h","board.h","uart.h" etc
> Whenever I am trying to include these files the message "cannot
> include file "(filename.h)" " appears
You must specify where is the header files location. You can set this
using build option. If you install CCS in c:\ti then then the header files
are in C:\ti\c5400\dsk5402\include.
> 2.Error "Undefined symbols" appears when
using functions such as
> 'uart_write_reg()','uart_read_reg()' etc
> 3.Warning entry point"_c_int00"
referenced but not defined appears
>
I think your problem is: forgot to add the librariy in the project.
If you want to use DSK library (using functions to access DSK peripherals)
you must include C:\ti\c5400\dsk5402\lib\dsk5402.lib in your project.
The third problem is because you didn't include run time library
C:\ti\c5400\cgtools\lib\rts.lib in your project.
Cheers > Can anyone help me solving these problems?
>
> Thanking in advance..
> Praju
>
> _____________________________________
> Note: If you do a simple "reply" with your email client, only the
author of this message will receive your answer. You need to do a "reply
all" if you want
your answer to be distributed to the entire group. >
> _____________________________________
> About this discussion group:
>
> To Join: Send an email to
>
> To Post: Send an email to
>
> To Leave: Send an email to
>
> Archives: http://www.yahoogroups.com/group/c54x
>
> Other Groups: http://www.dsprelated.com
> ">http://docs.yahoo.com/info/terms/
Reply by collins●May 8, 20032003-05-08
Hi prajumokeri,
Have you set the path for the include files in Project->Options ?
Martin.
On Wednesday 07 May 2003 08:18, prajumokeri wrote: > Hi,
> I have just started with code composer & dsk5402.I am trying to
> interface an FPGA kit with dsk5402 through rs232 interface.These are
> the problems I,m facing
> 1.I can't include headerfiles such as
"type.h","board.h","uart.h" etc
> Whenever I am trying to include these files the message "cannot
> include file "(filename.h)" " appears
> 2.Error "Undefined symbols" appears when using functions such
as
> 'uart_write_reg()','uart_read_reg()' etc
> 3.Warning entry point"_c_int00" referenced but not defined
appears
>
> Can anyone help me solving these problems?
>
> Thanking in advance..
> Praju
>
> _____________________________________
> Note: If you do a simple "reply" with your email client, only the
author of
> this message will receive your answer. You need to do a "reply
all" if you
> want your answer to be distributed to the entire group.
>
> _____________________________________
> About this discussion group:
>
> To Join: Send an email to
>
> To Post: Send an email to
>
> To Leave: Send an email to
>
> Archives: http://www.yahoogroups.com/group/c54x
>
> Other Groups: http://www.dsprelated.com
> ">http://docs.yahoo.com/info/terms/
Reply by prajumokeri●May 7, 20032003-05-07
Hi,
I have just started with code composer & dsk5402.I am trying to
interface an FPGA kit with dsk5402 through rs232 interface.These are
the problems I,m facing
1.I can't include headerfiles such as
"type.h","board.h","uart.h" etc
Whenever I am trying to include these files the message "cannot
include file "(filename.h)" " appears
2.Error "Undefined symbols" appears when using functions such as
'uart_write_reg()','uart_read_reg()' etc
3.Warning entry point"_c_int00" referenced but not defined appears