The error
#9 is INDICATE_ERROR_PROTECTED_BOOT_SECTION which is stating that the S record
being downlaoded is trying to program the area that the bootloader is running
from. As always it isn ot allowed to program a flash block you are currently
executing from. It does not relate to flash security.
The problem in
v6.0 is not a problem with the CodeWarrior program, but in the way the
defaults for the S record generation are set. To operate properly you need to
set the S record generation to :
- Check Sort By
Address
- Modify Max Record lenght to 80
- Modify EOL Charatcter to DOS from
Mac
This should resolve
the problem. Thanks.
-
Bill
-----Original Message----- From: Jacob Christ
[mailto:j...@pontech.com] Sent: Friday, January 30, 2004 11:05 AM To: 'edinstman' Cc: Motoroladsp Subject: [motoroladsp] RE: CW v6 56F800DEMO Bootloader problems
Andrew,
I'm still
using 5.1 (because I'm afraid to change version in the middle of a project), thanks for the heads up. I can believe that you are the only
one that has this problem right now, I would suspect that you are just the
first person to find the problem. Bleeding edge of technology and
all... I'm going to post this to the message board. I
would suspect that MW will fix the problem with in a week or two (Right
MW?).
Hmmm, what version is the bootloader firmware on you
chips? The version on mine is 1.3.
Jacob
-----Original Message----- From: edinstman [mailto:a...@hotmail.com] Sent: Friday, January 30, 2004 5:51 AM To: Jacob Christ Subject: Re:
CW v6 56F800DEMO Bootloader problems
Jacob,
Thanks for the
link. I have tried the software and my code is being bootloader but then it
returns the error #9, which I believe means that the flash is locked. When
I create my code in CW v5.1 using the SDK libraries it bootloads ok but not
when I use CW v6 with processor expert. Something is missing or was
supported in v5.1 that is no longer in v6 but I don't know what to
change. I contacted Metrowerks and they have put this down as urgent priority to fix but I have no idea as to how long it will take them. I
can't believe that I am the only person that has this problem as
anyone who tries to bootload their board with code written in CW v6 must
have the same problem.
Cheers
Andrew
---
In m...@yahoogroups.com, "Jacob Christ" <jacob@p...> wrote: > I
posted the S-Record loader at the following address: > >
http://www.pontech.com/products/DSP56Fxxx/index.html > >
It's not well documented right now, nor does every feature work, but
it does > upload S-Records quite well. > > Jacob > > P.S. Sorry for the ad in the free program, I couldn't
resist. > > -----Original Message----- > From: Andrew
Tarbert [mailto:andrew.tarbert@e...] > Sent: Thursday, January 29, 2004
9:16 AM > To: 'Jacob Christ' > Subject: RE:
[motoroladsp] CW v6 56F800DEMO Bootloader problems > >
Jacob, > > I'm trying to upload the Flash.elf.s file using
the Motorola boot loader but > Metrowerks have said that CW v6 does
not support this feature. I have been > in contact with them about
this and they have said its high priority for > them to fix this
problem but I have no idea of how long it will take. Please > could
you send me a copy of your program as this would be very much >
appreciated. > > Cheers > > Andrew P
Tarbert > Electronics Engineer > Edinburgh Instruments Ltd > 2 Bain Square > Kirkton Campus > Livingston EH54 7DQ > > Tel: +44 (0) 1506 425300 > Fax: +44 (0) 1506 425320 > www.edinst.com> -- > The information in this email may be
confidential, privileged and/or exempt > from disclosure under
applicable law. If you are not the intended recipient, > you may
not copy or use it, or disclose it to anyone else. Unauthorised use, > copying or disclosure is strictly prohibited and may be unlawful. The views > expressed in this e-mail are personal and may not
necessarily reflect those > of Edinburgh Instruments Ltd. or any of
its divisions, unless explicitly > stated otherwise. We do not
accept any liability or responsibility for: (1) > changes made to
this email after it was sent, or (2) viruses transmitted > through
this email or any attachment. If you have received this >
transmission in error please notify the sender immediately and delete
the > message from your email. > > For further
information on Edinburgh Instruments please visit our website at >
http://www.edinst.com
_____________________________________ Note: If you do a simple
"reply" with your email client, only the author of this message will receive
your answer. You need to do a "reply all" if you want your answer to be
distributed to the entire group.
_____________________________________ About this discussion group:
To Join: m...@yahoogroups.com
To Post:
m...@yahoogroups.com
To Leave: m...@yahoogroups.com
Archives: http://www.yahoogroups.com/group/motoroladsp
More Groups:
http://www.dsprelated.com/groups.php3
Yahoo! Groups Links
To
|